Miele G 8066 Manual

Issue Possible fault Solution
The wash cycle finishes
too early and the
indicator flashes
(fault code F..A appears
in the display)Before fixing the fault:
–Turn the machine off
with thebutton.
The filters in the wash
cabinet are clogged.Clean the filters. See
"Cleaning and Care".
The drain pump or the
non-return valve may be
blocked.Clean the drain pump and
the non-return valve, see
"Cleaning and Care".
The drain hose is kinked. Remove any kinks in the
drain hose.
Knocking noise in the...

Poor cleaning results
Issue Possible fault Solution
Dishes are not cleanThe dishes were not
loaded correctly.Load items so water can
reach all surfaces.
See "Use - Loading the
machine" for more
information.
The program was not
powerful enough.Select a more powerful
program. See the
"Program Guide".
Not enough detergent
was dispensed.Use more detergent, see
"Programming special
functions".
The spray arms are
blocked by tall items.Check if the spray arms
rotate freely. Rearrange...

Issue Possible fault Solution
White residue is visible
on cutlery and dishes,
clouding occurs on
glassware and film can
be wiped offNot enough rinse aid was
used.Use more rinse aid, see
"Programming special
functions".
The salt reservoir is
empty.Replenish reactivation
salt, see "Water softener".
The salt reservoir cap was
not properly screwed on.Reseat and screw the cap
on firmly.
Smears on glasses and
cutlery, bluish sheen on
the surface of glasses
and film can be wiped
offThe rinse aid...

Further fault codes
If fault codes are displayed which are
not described in the table:
Turn the machine off by pressing.
Turn the machine on again with.
Start the DRAINprogram.
Select a wash program to fill the
dishwasher’s boiler and tank.
If the DRAINprogram cannot be
started or if a fault is displayed again,
contact Technical Service.
Frequently asked questions
54 

In the event of a fault which you cannot
correct yourself or if the fault code "F..."
shows in the display field please
contact the Miele Service Department
at the phone number on the back of
these instructions.
Please quote the model and serial
number of your machine.
This information can be found on the
data plate (see also "Electrical
connection").
After sales service
55 

Installation Instructions
To prevent accidents
and machine damage
read these instructions
before
installation or use.
56 

Installation options
–Free-standing
–Undercounter
The machine can be installed under a
continuous counter or sink drain. The
recess must be at least 23
5/8" (60 cm)
wide, 235/8" (60 cm) deep and 321/4"
(82 cm) high.
Installation
Furniture and fittings installed
near the machine must be of a
commercial standard (able to
withstand the effects of steam) (e.g.
stainless steel).
Please refer to the installation
diagram supplied with the machine.
Leveling the machine
The dishwasher needs to...

Removing the lid
If necessary, remove the lid from the
machine to make installation possible.
Open the door.
Remove the fixing screws on the left
and right sides using a Phillips head
screwdriver.
Pull the machine lid approx. 5 mm
forwards, lift it upwards and remove.
Installation
58 

All electrical work must be
performed by a qualified person in
accordance with local and national
safety regulations.
The machine is equipped witha6ft.
(1.8 m), 12/4 AWG power cord, and a
NEMA L15-20 plug. It should be
connected to the main power supply
according to national requirements.
For technical data see the data plate
or wiring diagram supplied.
The machine must only be operated
with the voltage, frequency and fusing
shown on thedata plate.
Thedata plateis located on the rear of
the machine and...

Water inlet
Water in the machine must not
be used as drinking water.
The machine must be connected to
the water supply in accordance with
local and national regulations.
If the iron content in the water is too
high, there is a risk of corrosion
damage to the machine and its load.
If the chloride content of the water
exceeds 100mg/l, the risk of
corrosion damage to the load will
increase considerably.
The washer is constructed so it may
be connected to a water supply
without an extra non-return...