Miele G 8066 Manual

							4. Buzzer
(Programming level 5)
Programming level 5 allows you to
activate a buzzer to sound at the end of
a program or when a fault has
occurred.
To turn the buzzer off:
–Press
(Fault confirmation for F0E, F2E).
–Press
(turning off the power).
–Open the door at the end of the
program.
If the fault has not been fixed, the
buzzer will start again after power
has been restored.
Accessing programming level 5
Turn the machine off by pressing.
Press and hold theandbutton,
at the same timeturn the machine
on with the main switch. The
display shows the current program
statusP....
Theindicator lights.

Press thebutton 5 times. The
display shows5(programming
level 5).4.1 Setting the buzzer
Pressuntil5.01is displayed.
Pressonce, the display shows
the current setting0. The machine is
factory set to 0.
Pressuntil the desired setting0,
1, 2or3is displayed.
0= Buzzer is turned off (factory setting)
1= Program end
2= Fault display
3= Fault display and Program end
The warning buzzer "Door open"
cannot be deactivated.
Value set:
4.2 To save your changes

Press thebutton. The display
showsSP.

Press thebutton again. The
change has been saved.

Turn the machine off with the
button.
Programming special functions
41 
						

							5. Altering the program
duration (Programming level 6)
The program duration can be set
between 75 and 480 seconds.
Lengthening the program duration
cannot alter how the programs relate to
each other in terms of time, e.g. the
SHORT program will always be the
shortest program.
It is only possible to set a program
duration which is shorter than or equal
to the value set for the STANDARD
program.
To lengthen the program duration of
every program, start with the
INTENSIVE program.Accessing programming level 6
Turn the machine off with the
button.
Press and hold theandbutton,
at the same timeturn the machine
on with the main switch.
The display shows the current
program statusP....
Theindicator lights.
Press thebutton 6 times. The
display shows6(programming
level 6).
5.1 Altering the SHORT program
duration
Pressuntil6.01is displayed.
Pressonce, the display shows
the current setting90. The factory
setting is 90 seconds.
Press and holduntil the desired
value appears in the display. The
duration is set in 5 second
increments.
If you do not want to make any other
setting changes in this programming
level, proceed to step5.4.
Programming special functions
42 
						

							5.2 Altering the STANDARD program
duration
Select programming level 6.
Pressuntil6.02is displayed.
Pressonce, the display shows
the current setting120. The factory
setting is 120 seconds.
Press and holduntil the desired
value appears in the display. The
duration is set in 5 second
increments.
If you do not want to make any other
setting changes in this programming
level, proceed to step5.4.5.3 Altering the INTENSIVE program
duration
Select programming level 6.
Pressuntil6.03is displayed.
Pressonce, the display shows
the current setting180. The factory
setting is 180 seconds.
Press and holduntil the desired
value appears in the display. The
duration is set in 5 second
increments.
If you do not want to make any other
setting changes in this programming
level, proceed to step5.4.
5.4 To save your changes
Press thebutton. The display
showsSP.
Press thebutton again. The
change has been saved.

Turn the machine off with the
button.
Programming special functions
43 
						

							6. Resetting the factory default
settings
All settings can be reset to the factory
default settings in Programming level 7.
To do this you must first select the
factory setting and then confirm them.
After confirming the factory settings, all
adjustments are reset. Any changes
must be reentered if required.
Accessing programming level 7
Turn the machine off by pressing.
Press and hold theand
buttons,at the same timeturn the
machine on with the main switch.
The display shows the current
program statusP....
Theindicator lights.
Press thebutton 7 times. The
display shows7(programming
level 7).
6.1 Activating the factory setting

Pressuntil7.01is displayed.

Press. The display shows the
current setting:
00factory setting, or
PPcustomized settings.

Pressuntil the setting00(factory
setting) is displayed.
The factory settings are now selected.
If you have selected00by mistake

Pressto toggle between00and
pp.6.2 To save your changes
Press. The display showsSP.
Press thebutton again. Values
which had been changed are now
reset.
Turn the machine off with the
button.
All values which can be changed, are
now reset to the factory setting.
If the water hardness setting had
been changed this will reset to the
factory setting of 19 gr/gal (340 ppm
CaCO3). Please readjust to the
hardness level in your area.
IfPPwas selected and confirmed, the
customized settings were not reset.
Programming special functions
44 
						

							Cleaning the wash cabinet,
tank and filters
Wash cabinet and tank
Once a day
The tank should be checked and
cleaned regularly depending on the
soiling or number of wash programs.
Always check and clean at the end of
each workday.
Pressto start the DRAIN program.
See the "Program guide".
If the cleaning result is not
satisfactory, restart the program. It
will run again but for a shorter
duration.
Pressto restart the DRAIN
program.Filters
The water in the tank may be
hot. Before taking the filters out, the
water in the tank must be drained
away.
Be careful - glass splinters in the
filters could cause injury.
The machine must not be used
without all the filters in place!
The filters should be checked and
cleaned regularly depending on the
soiling or number of wash programs.
Always check and clean at the end of
each workday.
Cleaning and Care
45 
						

							Flat filter
Take the front filter out first, by lifting
it up a little at the front.
Remove the rear filter, by lifting it up
a little at the rear.
Clean the filters thoroughly under
running water.
Reinsert the filters in the reverse
order. Make sure that you reinsert the
filters correctly. Ensure that the filters
sit flat in the base of the wash
cabinet.Fine filter
Remove the flat filters.
Turn the fine filter counterclockwise
to remove it from the drain.
Spin the propeller of the drain pump
few turns in both directions and feel
for resistance.
Clean the filter thoroughly under
running water.

Reinsert the fine filter into the drain
and turn it clockwise to secure it.

Replace the flat filters in the reverse
order. Ensure that the filters sit flat in
the base of the wash cabinet.
Cleaning and Care
46 
						

							Cleaning the control panel
Only clean the control panel with a
damp cloth, a plastic cleaner or
disinfectant.
Do not use too much water when
cleaning the controls. Water could
penetrate into the electronics and
cause damage.
Never use abrasive cleaners,
scouring pads, steel wool, thinners,
caustic (oven)-, glass-, all purpose
cleaners or cleaners containing
ammonia on the dishwasher.
They will damage the surface.
Cleaning the exterior
Clean the exterior with a solution of
warm water and liquid dishsoap
applied with a soft sponge. Wipe dry.
Cleaning the spray arms
Sometimes particles get stuck in the
spray arm jets.
The spray arms should be inspected
and cleanedevery4-6months.
Unscrew theupperspray arm.
Remove the lower basket.
Unscrew thelowerspray arm.
Use a sharp pointed object to push
particles into the spray arm jets and
rinse thoroughly under running water.
To rinse out particles easier, open the
caps of thelowerspray arm. After
cleaning close the caps tightly.
Replace the spray arms and check
that they rotate freely.
Check placement of flat filters - they
should have good contact to wash
chamber, else bigger particles may
clog the spray arms.
Cleaning and Care
47 
						

							Cleaning the drain pump and
non-return valve
If water has not been drained at the
end of a program the drain pump and
the non-return valve may be clogged.
The water in the tank may be
hot. Allow the water to cool.
Remove the flat and fine filters from
the wash cabinet.

Turn the non-return valve to the front
and take it out.

Rinse the non-return valve thoroughly
under running water.

Make sure that the vent hole is not
clogged.

Clean the vent hole if necessary with
a pointed object.The non-return valve is beneath the
drain pump.
Before returning the non-return valve,
check that the drain pumpand
filterare not clogged.
Clean the filters and if necessary
remove any objects from the pump.
Reinsert the non-return valve.
Replace the filters in the reverse
order. Ensure that the flat filter sits
flush in the base of the wash cabinet.
Cleaning and Care
48 
						

							Cleaning the water inlet filters
To protect the water inlet valve, filters
are incorporated in the intake hose
attached to the water supply. If the
filters are soiled they must be cleaned
to ensure sufficient water intake to the
wash cabinet.
The plastic valve housing on the
intake hose contains electrical
components and should not be
submerged, or run through water.
Cleaning the filter
Disconnect the machine from
electricity (unplug it or "trip" the
circuit breaker).
Close off the water supply and
unscrew the water inlet valve.Carefully remove the rubber seal.
Take out the filters with needle nose
pliers.Rinse the large area filter (1)
and fine filter (2) under running water,
and replace if necessary.
Return the filters and seal. Make sure
they are seated correctly.
Screw the intake hose back on the
water valve, checking that it is not
cross-threaded.

Open the water supply. Check for
leaks. Tighten the connections if
necessary.
Cleaning and Care
49 
						

							With the aid of the following guide, minor problems can be fixed without a service call.
Repairs should only be carried out by Miele Service in accordance with local
and national safety regulations. Unauthorized repairs could cause personal
injury or machine damage.
Technical faults
Issue Possible fault Solution
Dishwasher does not
startThe door is not properly
closed.Close the door firmly.
The machine is not
plugged in.Insert the plug.
The fuse has tripped. Reset the circuit breaker.
Dishwasher stops
during a programThe fuse has tripped. Reset the circuit breaker.
See the data plate for
minimum Ampere.
The door is not properly
closed.Close the door firmly.
A few minutes after
starting a program, the
indicator flashes
(fault code F..E
appears in the display)The water supply is
closed.Open the water supply.
The water inlet filter is
clogged.Before fixing the fault:
–
Turn the machine off
with thebutton.
Then:
–
Clean the water inlet
filter, see "Cleaning and
Care".
The waterproof system has
activated.Call the Miele Technical
Service Department.
The water pressure at the
water inlet is lower that
14.5 psi.Consult a plumber.
Frequently asked questions
50