Miele G 8066 Manual

							Changing a program
If the selected program has not yet
been started:
Press the desired wash program
button.
Press the "Start"button.
Cancelling a program
Once a program is running it should
only be cancelled in extreme cases,
e.g. when items in the machine rattle or
bump against each other and have to
be rearranged.
Press the "Start"button for approx.
3 seconds. The program is
cancelled.
Open the door.
Caution! Water and items in the
machine may be hot. There is a
danger of burning or scalding.

Arrange the load securely.

Close the door.

Restart the wash program.
Turning off
Select theDRAIN program.
The water will be drained away. At the
end of the program.
Press thebutton.
Use
31 
						

							Program 1) Use Powder detergent 2)
Follow manufacturers
instructions

INTENSIVE
3 minFor heavily soiled dishes with dried
on food40 gon the inside of the door
Add 20 g (1 ½ tablespoon)
after every five programs.

STANDARD
2 minFor normally soiled dishes 40 gon the inside of the door
Add 20 g after every five
programs.

SHORT
1.5 min"Quick program" for lightly soiled
dishes.40 gon the inside of the door
Add 20 g after every five
programs.

DRAINTo drain the wash water also for
cleaning the inside of the cabinet,
e.g. at the end of a workday.
1) The short program durations are only possible when the machine is connected
to hot water.
2) Liquid detergent is dispensed automatically.
Program guide
32 
						

							Program 1) Program cycle
Main wash
3) 4)Run-off Final rinse
3) 5)

INTENSIVE
3 min149°F/65°C
160 sec5 sec 194°F/90°C
10 sec

STANDARD
2 min149°F/65°C
100 sec5 sec 194°F/90°C
10 sec

SHORT
1.5 min149°F/65°C
70 sec5 sec 194°F/90°C
10 sec

DRAIN2 min 45 sec
3) To change the wash and rinse temperatures and rinse duration, see
"Programming special functions".
4) Durations may vary
5) Times will depend on drain and rinse durations.
For applications where high temperature sanitizing is required according to
Provincial Food Code, only use a minimum temperature of 82°C with a holding
time of 10 seconds.
Program guide
33 
						

							Every change of a factory setting
should be documented.
Record any changes in the field
"Value set: ___________".
When special function settings are
changed or the dispensing systems are
primed, the dishwasher will
automatically be drained. To save
energy and time, these tasks should be
done when the dishwasher tank is
empty.
1. DOS 1 Detergent dosage
concentration level and
venting the dispensing system
(Programming level 2)
G 8066
The models G 8066 and G 8066 WES
DOS are designed for use with powder
detergents. The powder detergent is
placed directly on the inside of the
door.
The models G 8066 and G 8066 WES
DOS can also be connected to an
optional DOS Module G 60 if you wish
to use liquid detergent.
In this caseOption 2needs to be
programmed into programming level 2.
G 8066 WES DOS
The models G 8066 DOS and G 8066
WES DOS are equipped with a built-in
dispensing pump and a reservoir for
liquid detergent.
In this caseOption 1needs to be
programmed into programming level 2.
A conversion kit is available for
connecting an external detergent
container to the built-in detergent
dispensing pump.
In this caseOption 3needs to be
programmed into programming level 2.
Programming special functions
34 
						

							Accessing Programming level 2
Turn the machine off by pressing.
Press and hold theandbutton,
at the same timeturn the machine
on with the main switch.
The display shows the current
program statusP....
Theindicator lights.
Press thebutton twice. The
display shows2(programming
level 2).1.1 Setting the detergent dispensing
method
Press thebutton once.
The display shows2.01
Pressonce. The display shows
either0, 1, 2or3.
0=powder detergentplaced on the
inside of the door (G 8066)
1=liquid detergentdispensed via the
built-in dispensing pump,Option 1
(G 8066 WES DOS)
2=liquid detergentdispensed via an
external DOS Module,Option 2
(G 8066)
3=liquid detergentdispensed via the
built-in dispensing pump connected to
an external container,Option 3
(G 8066 WES DOS)
Press thebutton until the desired
option is displayed.
If you do not want to make any other
setting changes in this programming
level, proceed to step1.4.
Programming special functions
35 
						

							1.2 Setting the detergent dosage
concentration level
If the dispensing method has been
programmed for liquid detergent, you
can adjust the dispensing
concentration.
Set the dispensing concentration
according to the detergent
manufacturer’s recommendations
and the applications.
Example: If the manufacturer
recommends a detergent concentration
of 0.5%, a value of 0.50 should be set.
Select programming level 2.
Pressuntil2.02is displayed.
Press thebutton. The liquid
detergent dosage concentration is
displayed in %.
0.00-1.00=0.0%-1%dosage
concentration level
(factory default setting0.20= 0.2 %).

Press and holduntil the desired
value appears in the display.
The dosage concentration level has
been set.
Value set:
If you do not want to make any other
setting changes in this programming
level, proceed to step1.4.
1.3 Venting the dispensing system
Select programming level 2.
Pressuntil2.03is displayed.
Press. The display showsdo1.
Press thebutton.
The dispensing system will be vented
automatically.0will appear in the
display when the venting process is
completed.
If you do not want to make any other
setting changes in this programming
level, proceed to step1.4.
1.4 To save your changes
Press thebutton. The display
showsSP.

Press thebutton again. The
change has been saved.

Turn the machine off with the
button.
Programming special functions
36 
						

							2. DOS 2 Rinse aid dosage
concentration level and
venting the dispensing system
(Programming level 3)
Accessing programming level 3
Turn the machine off by pressing.
Press and hold theandbutton,
at the same timeturn the machine
on with the main switch.
The display shows the current
program statusP....
Theindicator lights.
Press thebutton 3 times. The
display shows3(programming
level 3).
2.1 Selecting the rinse aid dispensing
method
Press thebutton once. The
display shows3.01.
Pressonce. The display shows
either0or1.
0= Built-in pump, container external
(G 8066)
1= Built-in pump and container
(G 8066 WES DOS)

Press thebutton until the desired
option is displayed.
If you do not want to make any other
setting changes in this programming
level, proceed to step2.4.2.2 Setting the rinse aid dosage
concentration level
Set the dosage concentration
according to the detergent
manufacturer’s recommendations
and the application.
Example: If the manufacturer
recommends a detergent concentration
of 0.03 %, a value of 030 should be
set.
Select programming level 3.
Pressuntil3.02is displayed.
Press thebutton. The liquid
detergent dosage concentration
shows in the display in %.
000-100= 0.0 % - 0.1 % dosage
concentration level
(factory default setting030=
0.030 %).
Press and holduntil the desired
value appears in the display.
The dosage concentration level has
been set.
Value set:
If you do not want to make any other
setting changes in this programming
level, proceed to step2.4.
Programming special functions
37 
						

							2.3 Venting the dispensing system
Select programming level 3.
Pressuntil3.03is displayed.
Press. The display showsdo2.
Press thebutton.
The dispensing system will be vented
automatically.0will appear in the
display when the venting process is
complete.
If you do not want to make any other
setting changes in this programming
level, proceed to step2.4.2.4 To save your changes
Press thebutton. The display
showsSP.
Press thebutton again. The
change has been saved.
Turn the machine off with the
button.
Programming special functions
38 
						

							3. Setting the main wash or
final rinse temperature and/or
final rinse duration
(Programming level 4)
Any changes to the wash
temperature and/or the temperature
holding time should be recorded in
the appropriate section of the
"Program guide".
The factory default settings for the main
wash and final rinse temperatures and
for the final rinse duration are given in
the "Program guide".
A main wash temperature of 68 - 149 °F
(20 °C - 65 °C) can be set in
Programming level 4. The final rinse
temperature depends on the wash
temperature and is by standard 68°F
(20 °C) above the wash temperature
(Offset). It can be altered to a range of
59°F to 77°F (15 °C to 25 °C).
The final rinse duration for all wash
programs can be set between 3 and
10 seconds.
For applications where high
temperature sanitizing is required
according to Provincial Food Code,
only use a minimum temperature of
82°C with a holding time of 10
seconds.Accessing programming level 4
Turn the machine off by pressing.
Press and hold theandbutton
andat the same timeturn the
machine on with the main switch.
The display shows the current
program statusP....
Theindicator lights.
Press thebutton 4 times. The
display shows4(programming
level 4).
3.1 Setting the main wash
temperature
Pressuntil4.01is displayed.
Pressonce, the display shows
the current setting65. The machine
is factory set to 65 °C.
Press and holduntil the desired
value appears in the display.
If you do not want to make any other
setting changes in this programming
level, proceed to step3.4.
Programming special functions
39 
						

							3.2 Setting the offset range of the
final rinse temperature
Select programming level 4.
Pressuntil4.02is displayed.
Pressonce, the display shows
the current setting20. The machine is
factory set to 20 °Cabove the main
wash temperature.
It means, if the factory set wash
temperature is 65 °C, the final rinse
temperature is 85 °C.
Press thebutton until the desired
temperature is displayed.
The final rinse temperature should
be set approximately 20 °C higher
than the main wash temperature. For
applications where high temperature
sanitizing is required according to
Provincial Food Code, only use a
minimum temperature of 82°C with a
holding time of 10 seconds.
If you do not want to make any other
setting changes in this programming
level, proceed to step3.4.3.3 Selecting the final rinse duration
Select programming level 4.
Pressuntil4.03is displayed.
Pressonce, the display shows
the current setting10. The display will
appear in tenths of a second. The
factory setting is 10 seconds.
Press and holduntil the desired
value appears in the display.
If you do not want to make any other
setting changes in this programming
level, proceed to step3.4.
3.4 To save your changes
Press thebutton. The display
showsSP.
Press thebutton again. The
change has been saved.
Turn the machine off with the
button.
Programming special functions
40