Midway Cruis N Exotica Operations Manual For 39 Dedicated Game With Motion Seat

Service - 7
 
 
 
 
 
Viewing Glass Service
To service Monitor Bezel…
¾  Switch off the power to the game machine and unplug the AC line cord.
¾  Lift open the Marquee Housing. Refer to service instructions for Marquee.
¾  Grasp the monitor bezel at the bottom and lift it out of cabinet.
¾  Perform the desired repair or equipment replacement.
¾  Wipe the bezel clean before reinstallation.
To service the Monitor (CRT)…
We recommend that you read the WARNINGS thoroughly before beginning this procedure....

Service - 8
To service the Control Cabinet…
Refer to the Control Cabinet Service illustration.
¾  Switch off the power to the game machine and unplug the AC line cord.
¾  Remove the tamper resistant screws from either side of the control cabinet used to fasten it to
the cabinet brackets in the main cabinet.
¾  Slide the control cabinet halfway back along the rails to expose wiring. Label and disconnect
all wiring.
¾  Continue to slide the cabinet away from the main cabinet until it clears the mounting...

Service - 9
Dashboard Service
To service the Center Control Pod…
Refer to the Center Control Pod Service illustration.
¾  Switch off the power to the game machine and unplug the AC line cord.
¾ Remove the Dashboard. Refer to service instructions for Dashboard.
¾  Remove the steering mechanism. Refer to service instructions for steering mechanism.
¾  Disconnect the light bulbs from the sockets for both the Radio and Start buttons, and set aside.
¾  Remove 5 hex head screws that form the outline of the pod...

Service - 10 Dashboard PCB Service, continued
¾  Perform the desired repair or equipment replacement.
¾  Connect the ribbon and power cable to a Dashboard PCB. NOTE:
 The red stripe on the ribbon
cable must be lined up with pin 1 on the PCB, and the black wire on the power cable must line
up with pin 1 on the power connection for the Dashboard.
¾  Reattach the PCB to the pod, and then fasten the pod to the dashboard.
¾  Check for pinched wires.
¾  Reinstall the Dashboard and fasten in place with the...

Service - 11
Control Pod, Buttons and Shifter Service
To service View Buttons…
Refer to the Control Pod, Buttons and Shifter Service illustration.
¾  Switch off the power to the game machine and unplug the AC line cord.
¾  Remove the 4 tamper-resistant buttons used to fasten the faceplate.
¾  Pull the plate forward enough to expose the switches.
¾  Label and disconnect the wiring for the pod(s) being serviced.
¾  Lift assembly completely out of the pod and set aside.
¾  Perform the desired repair or...

Service - 12
To service Steering Assembly…
Refer to the Steering Assembly Service illustration.
¾  Switch off the power to the game machine and unplug the AC line cord.
¾ Remove the Dashboard. Refer to service instructions for Dashboard
.
¾  Remove 6 screws used to fasten the cover plate to the center of the steering wheel. Remove
the cover plate and set aside.
¾  Remove the 3 screws used to fasten the wheel hoop to the shaft. Pull the wheel hoop off of the
dashboard.
¾  If present, remove 4 flange nuts...

Service - 13 Keypad Service, continued

 Lift the keypad out.

 Perform the desired repair or equipment replacement.
¾  Reinstall keypad, seat the spacers and fasten in place with the nuts provided.
¾  Reinstall Dashboard and fasten with hardware provided.
Keypad Service
To service Control Cabinet Speaker…
    
This speaker is located just above the pedal assembly.
¾  Switch off the power to the game machine and unplug the AC line cord.
¾  Remove the Control Cabinet. Refer to service instructions for...

Service - 14
To service Coin Meter…
¾  Switch off the power to the game machine and unplug the AC line cord.
¾  Unlock the cash door and swing it open.  Remove the cash tubs.
¾  The meter is located on a plate at the bottom of the vault. Remove the screws and lift the plate
just enough to disconnect the meter wires from the harness.
¾  Record the meter count before testing or replacement.
¾  Perform the desired repair or equipment replacement.
To service Coin Mechanism…
¾  Switch off the power to the...

Service - 15
To service CPU Board Assembly…
¾  Switch off the power to the game machine and unplug the AC line cord.
¾  Unlock and remove the rear door to expose the electronics assembly.
¾  Locate the CPU Board assembly.
¾  Carefully note the orientation of the JAMMA connector and the other cables.  Extract the
harness and other cables from the board connectors.
¾  Remove CPU board assembly mounting screws.  Lift the board out of the cabinet and set in a
safe place.  Use anti-static bags and protective...

Service - 16
To service the Power Supply…
¾  Switch off the power to the game machine and unplug the AC line cord.
¾  Unlock and remove the rear cabinet door.
¾  Unplug the IEC AC connector from the rear of the supply and the DC connector from the front.
¾  Remove the two front and two rear screws from the supply, then lift it off of the power chassis.
Note voltage setting.
¾  Perform the desired repair or equipment replacement.
¾  Be sure to set the voltage switch to the correct value prior to...