Midway Cruis N Exotica Operations Manual For 39 Dedicated Game With Motion Seat

Wiring - 7
CPU DIP Switch 2 Settings
DIP Switch 2 Settings SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8
COUNTRY CODE
    USAOFF*OFF*OFF*OFF*OFF*
 GERMANYONOFFOFFOFFOFF
FRANCEOFFONOFFOFFOFF
CANADAONONOFFOFFOFF
SWITZERLANDOFFOFFONOFFOFF
ITALYONOFFONOFFOFF
UKOFFONONOFFOFF
SPAINONONONOFFOFF
AUSTRALIAOFFOFFOFFONOFF
JAPANONOFFOFFONOFF
TAIWANOFFONOFFONOFF
AUSTRIAONONOFFONOFF
BELGIUMOFFOFFONONOFF
SWEDENOFFOFFOFFOFFON
FINLANDONOFFOFFOFFON
NETHERLANDSOFFONOFFOFFON
NORWAYONONOFFOFFON
DENMARKOFFOFFONOFFON
HUNGARYONOFFONOFFON...

Wiring - 8
NOTES 

	


70
70


	


	

CAUTION
This Video Game Machine (VGM) uses complex electronic components that are very sensitive to
static electricity. Observe the following precautions before handling electronic assemblies.
Failure to do so may void your warranty and could damage electronic assemblies.
♦  Before servicing electronics, turn off AC power to the VGM. Wait for capacitors to discharge.
♦  Before touching or handling electronic assemblies, discharge static electricity...

Troubleshooting - 2
Coin Mechanism and Pricing Troubleshooting Table
SYMPTOM CAUSE REQUIRED ACTION
Improper settings at
Pricing Menu1.  Press and hold TEST MODE switch inside coin
door to enter Menu System. Select SWITCH
TEST from Diagnostics menu. Conduct test to
confirm operation of game switches.
2.  Select either the STANDARD 
or CUSTOM
PRICING MENU from Game Adjustments Menu.
Verify units and credits are set correctly.•  Video Game Machine (VGM)
accepts currency or tokens,
but number of credits per...

Troubleshooting - 3
Coin Switch and Meter Wiring
FACTORY STANDARD
OPTIONAL WIRING
INCORRECT WIRING
A connection between JAMMA coin input pins will cause twice the desired credits for each coin inserted.
A coin meter with a defective or missing diode may eventually damage driver circuits on the CPU Board. 

Troubleshooting - 4
Startup Troubleshooting Table
SYMPTOM CAUSE REQUIRED ACTION
Power problem1. Check power is switched on.
2. Make sure fans are turning. If not: Is the power
supply connected to its power cable? Is power
supply turned on?
3.  Plug cord into AC power outlet. Verify presence
of AC line voltage.
Improper line voltage
switch settingTurn off power. Unplug AC line cord. Check line
voltage switch. If necessary, set it to agree with
local AC line voltage. Retest game.
Open fuse1. Turn off...

Troubleshooting - 5
Startup Troubleshooting, continued
SYMPTOM CAUSE REQUIRED ACTION
Power problem1.  Inspect circuit boards under low-light conditions.
The LED’s glow and the fan turns when
processor circuits receive voltage and indicate
presence of DC from power supply. However,
voltages or signals may not be normal.
2.  Turn on power. Set the digital voltmeter to the
20-volt DC setting and measure DC voltages at
power connector pins. Adjust the +5V source if
necessary. Refer to the Cabinet Wiring...

Troubleshooting - 6
Startup Troubleshooting, continued
SYMPTOM CAUSE REQUIRED ACTION
Faulty coin
mechanism1.  Unlock and open coin door. Check each currency
acceptor to assure proper mounting. Verify each
release latch is closed and locked.
2.  Test mechanism with good and bad coins to see
if mechanism accepts and rejects currency
correctly.
3.  Inspect to see if external acceptor indicators
(Pricing, Flashing Arrows, etc.) are lit.
4.  Verify each acceptor operates properly by
placing it in working...

Troubleshooting - 7  
Linking Problem Troubleshooting Table
SYMPTOM CAUSE REQUIRED ACTION
Faulty wiring 1.  Do not extend linking cables supplied with VGM.
2. Do not use standard telephone type couplers or
wiring for linking.• Cannot connect multiple
Video Game Machines
(VGMs)  together
Improper linking
hardwareUse required Fire Wire Cable. Array completion
requires basic kit brackets and spacers.
Improper settings1.  Record any error messages that occur during
self-test.
2.  From the Diagnostic Menu...

Troubleshooting - 8
Player Control Troubleshooting Table
SYMPTOM CAUSE REQUIRED ACTION
Faulty switches or
lamps1.  Press and hold TEST MODE switch inside coin
door to enter Menu System. Select SWITCH
TEST from Diagnostic Menu. Conduct tests to
confirm switch operation.
2.  Press and hold TEST MODE switch inside coin
door to enter Menu System. Select LAMP TEST
from Diagnostic Menu. Conduct tests to confirm
lamp operation.
3.  Check for loose parts or wires caught in switch
contacts.
4.  Check continuity...