Metz Clarus 32 Ml Operating Instructions

81
• Use the - +key to select the desired scope of
operation and press the OK key to save the
new setting.
2 & & & 
This menu permits you to configure the
use of the TV set to a certain degree.
All of the functions listed for the 1&
menu are available and are supple-
mented by the following functions:
- Childlock
- Timer control (sleep timer)
- Automatic station search
- Transfer of the TV station
table from the TV set to a
Data Logic video recorder.
- Editing functions in the sta-
tion table
3 & & &...

82
30. Operation without the 
Remote Control
Operation without the remote control is provided
as an emergency measure in case the batteries of
your remote control are exhausted or the remote
control is not readily available.
The local controls and the power switch are loca-
ted on the left side at the back of the TV set.
Switching on
Press the main power switch on the TV set. After
about five seconds, the TV set is switched on with
programme position 1 or the programmed initial
programme position...

83
When receiving a dual-language pro-
gramme, you can switch between the
two sound channels.
In TV mode, press and hold the yellow
key  until the sound function Sound
mode is selected.
Then use the 
-+
key to select Sound 1
or Sound 2.
32. Sound 1, Sound 2
Headph. Vol.
Sound mode Cannel 2
Spatial
Spatial 
Sound mode Cannel 2
Balance 
31. Connecting Headphones
The headphone socket is located on the right side
at the back of the TV set.
Tilt the flap on the Milos up with your fingernail.
On the Puros or...

84
33. Cleaning the TV Set
Before cleaning the set, always switch it off
with the mains switch!
Incorrect treatment and cleaning of the screen sur-
face can cause irreparable damage to it. You
should therefore always observe the following
instructions for treatment and cleaning of the set.
T
reatment:
Always treat the screen surface very carefully.
Take care not to damage it mechanically by
shocks, impact, scratching or scraping.
Keep sharp, pointed and hard objects away from
the surface of the screen....

85
34. Connections
 S-VHS or. Y/C in (e.g. camcorder)
 FBAS/Video in (e.g. digital camera or camcorder)
 Audio in   R/L (e.g. camcorder)
( Headphone socket, diameter 3.5 mm
(  
right side

Service socket for
use by your dealer
Antenna socket
35. Connectionson the rear side
Viewed from below
607 47 2042.A1 Clarus GB  04.12.2007  9:59 Uhr  Seite 85
 

86
35. Connections on the Rear of the Set
(covered by a flap)
Viewed from below
With the aid of an optical audio cable (Toslink cable, available from your
dealer), the digital audio signal (AC3) provided by the TV set can be extracted
for external processing.
HDMI connector 
Signal type
HDMI 
(Video/Audio
digital IN)
OUT
Digital
Audio
Power connection
Video IN
YCbCr in
YUV in
OUT
Audio
EURO sockets for connection of
external AV devices
Video and audio IN/OUT
Video IN 
DVI-I connector 
Signal type DVI-D...

87
35.1 Connecting a Hifi Amplifier/AV Receiver
Metz LCD-TV
HiFi-amplifier
AV-Receiver

Digital audio signal formats (depending on the source)
analogue audio signal R+L (stereo)
!Centre IN is always possible if the AV receiver offers this.
Can be used in combination with or if this option is available.
It is always possible to use the TV speakers as the centre speaker if the AV receiver
has this output available. The advantage of this is that the TV speakers can be used
as the centre speaker, thus...

88
35.1 Connecting a Hifi
Amplifier/AV Receiver
Registering the AV Device with the TV
• Enter the TV menu by pressing MENU.
• Press the yellow key  to open the AV Devices
menu.
• Use the cursor control key to select Hifi
Amplifier in the device selection.
• Press OK twice, use the cursor control key to
select Signal Types, and press OK..
• For connection type , select the signal type
Signal IN - SPDIF“.
For connection type , select the signal type
Signal IN – Stereo.
Confirm the setting by pressing...

89
36. Copying between AV Devices
Direct recording
Opening the menu
If you wish to copy a recording from one of the
AV devices connected to your TV set (such as a
DVD player) to another connected AV device (such
as a video recorder), you must do this by means
of a direct recording operation. In this case, the
signal arriving at one of the EURO sockets is redi-
rected to the other EURO socket, from where it
can be recorded.
Example: you have a DVD player and a
video recorder connected to
the EURO sockets...

90
• Use the cursor control key to select the line
Recording device.
If only one such device exists, it is then display-
ed. If further recording devices exist, you can
select the desired device with the aid of 
the 
-+
key.
• Press the OK key to save the settings.
• On the playback device (in this example, the
DVD player) start the film which is to be copied.
• On the recording device (in this example, the
video recorder), select the AV programme posi-
tion (in most cases AV1).
• On the recording...