Metz Clarus 32 Ml Operating Instructions

101
DiSEqC makes it possible to control the satel-
lite antenna digitally via the existing antenna
cable and is a prerequisite for the reception of
signals from more than two satellites (e.g.
Astra, Eutelsat, Hotbird).
If you wish to receive signals from at least three
satellites (e.g. ASTRA 19.2°, Eutelsat 16°, Hot-
bird 13°) the antenna system can be controlled
only with the aid of DiSEqC.
This menu item is not available in a 2**
menu.
Switching DiSEqC on and of
f
• Press the MENU key to open
the TV...

102
You can set up to four satellites in the menu Con-
figuration. No satellite is set in the factory.
The LNB frequency is used to switch between the
high and low frequency bands. The default fre-
quencies Low band 9.75 GHzand High band
10.60 GHzare set in the factory.
Selecting satellites
• Press the MENU key to open the TV menu.
• Press the red key  to open the menu Confi-
guration.
• Press the appropriate nume-
ric key (in this example 
to
select DVB-S.
• Press the appropriate nume-
ric key (in this...

103
The DVB-S station search scans the entire recep-
tion band for TVand radio stationsand stores
them in separate TV and radio station tables. For
details of the DVB radio mode, see Section 29 in
the operating instructions for the TV set.
If you are not satisfied with the order in which the
stations are stored, you can move stations to other
positions in the table or delete them. For further
details, see Section 24, Sorting stations in the
operating instructions for the TV set.
The station search will...

104
For the manual search, you must know the fre-
quency, the symbol rate and the polarisation of
the station for which you want to search.
Executing the manual search
• Press the MENU key to open the TV menu.
• Press the red key  to open the menu Confi-
guration
• Press the appropriate numeric key (in this exam-
ple 
to select DVB-S.
• The cursor is located on the line LNB supply
voltage.
• Press the appropriate nume-
ric key (in this example 
 to
select Manual search.
• The cursor then moves to...

105
With the menu item, General settings, you can
specify whether or not the data are to be saved in
the non-volatile memory of the TV set when trans-
mission parameters are changed.
This update function applies to stations which use
different transmission parameters at different times
of the day, such as when they transmit regional
programmes.
Setting the data update function
• Press the MENU key to open the TV menu.
• Press the red key  to open the menu Confi-
guration.
• Press the appropriate nume-...

106
ProblemPossible causeRemedy
TV set does not react
to commands from
the remote control• No line of sight between the
remote control and the TV set.
• Sunlight is shining directly on
the infrared window of the TV
set.
• Batteries of the remote control
are exhausted.
• TV set has been switched off
with the main power switch.
• Fault in the internal processor.• Remove any obstacles
between the units.
• Prevent sunlight from
shining on the set.
• Replace the batteries.
• Switch on the TV set
with the main...

107
Data Logic does not
work.
AV device (video
rec.) independently
breaks off recording• The Data Logic video recorder
with data transfer has not been
registered correctly.
• The Scart cable does not have
all pins connected through.
• Wrong data logic setting (see
also ch. 19.1)• Open the menu AV
devices and register
the Data Logic video
recorder as video recor-
der 1 with Data Logic
On.
• Use a Scart cable in
which all pins are con-
nected through.
• Set the data logic setting
to Mode 2 from Mode 1...

108
Various programs are transmitted with several
audio channels (e.g. multilingual or Digital
Audio).
If you are receiving a multilin-
gual programme the informa-
tion box on the bottom left of
the screen features the
logo.
Press F2to see the list of available languages.
Open menu:
• Press F2.
Press F2 briefly to run the
function programmed for
the key (see Chapter 18.
Programming function
keys).
Press F2 for approx. 3
seconds and the max. possi-
ble selection is displayed.
• Press numeric key 
and...

109
To connect a PC to the LCD TV, you must first regi-
ster the PC with the LCD TV; see Chapter 25
Registering AV Devices.
Set the signal type for the PC to DVI-A (analogue
with VGA cable) or DVI-D (digital with DVI cable),
depending on the connection type. Use a suitable
connection cable to connect the PC to the LCD TV.
Power on the LCD TV, press AV, and select the
PC connection with the respective number key.
Power up the PC and wait. Usually, the LCD TV
will recognise the PC and display the image....

110
Various pay TV stations broadcast portal stations.
These portal stations are filled with sub-stations or
optional channels.
In station search (see ch. 22) in Search settings
the setting all, only free or free+CICAM
must be set so that these stations can be found
too.
After a station search, the portal sta-
tions and the accompanying optional
channels (may also be identified in the
station table as SID=xy) will be shown
in the station table on various program
places.
We have programmed a simple way...