Marantz Vp 12s2 DLP Projector User Manual
Here you can view all the pages of manual Marantz Vp 12s2 DLP Projector User Manual. The Marantz manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 21
ENGLISH 17 •Press the ZOOMkey, the NORMALkey or the FULLkey on the remote controller for the 4:3 aspect ratio video source. •Press the FULLkey on the remote controller for 16:9 aspect ratio video source, such as 1080i, 1035i, and 720p video systems. •Press the FULLkey on the remote controller for the squeezed video source. See “Setting”. ( P.24) The Screen Images in a 16:9 screen ❖Original Source Image ❖Full mode The 16:9 squeezed image is displayed with the correct aspect. ❖Normal mode ❖Zoom mode The...
Page 22
ENGLISH 18 •Press the ZOOMkey, the NORMALkey or the FULLkey on the remote controller for the 4:3 aspect ratio video source. •Press the FULLkey on the remote controller for 16:9 aspect ratio video source, such as 1080i, 1035i, and 720p video systems. •Press the FULLkey on the remote controller for the squeezed video source. See “Setting”. ( P.24) The Screen Images in a 4:3 screen ❖Original Source Image ❖Full mode The 16:9 squeezed image is displayed with the correct aspect. ❖Normal mode ❖Zoom mode The...
Page 23
ENGLISH 19 1.Press the STANDBYkey on the remote controller or the POWERkey on the projector. 2.The fan continues to run for a while to reduce internal heat. The POWER ON indicator flashes in blue and no key will be active. After about one minute of cooling has been done, the unit turns off and the STANDBY indicator lights up. Notice: Do not pull out the AC power cord until the projector turns in standby mode. Notice : - Do not pull out the power cord suddenly in the state of “POWER ON. It can cause a...
Page 24
ENGLISH 20 Picture Adjust Contrast Main Menu Item Main Menu Item 0 100 Brightness 0 63 Color 0 100 Sharpness 0 31 Tint R50 G50 Noise Reduction 0 63 Color Temp. (Temperature) L M H Fine Menu Setting Aspect Lamp modeHigh / Low Cinema Auto / Off Black Setup 0IRE / 7.5IRE High Bright On / Off Component Video System RGB System Full Normal Through Zoom Auto NTSC PA L 480p 540p 576p 720p 1035i 1080i Auto NTSC PA L 480p 540p 576p 720p 1035i 1080i Auto NTSC PA L SECAM Display Keystone V (Vertical) Keystone H...
Page 25
Refer to the on-screen menu for making various adjustments and settings. (P.20)1.Press the MENUkey. The MENU appears. 2.Use 3/4/1/2keys to select a menu item. 3.Make adjustments in Picture Adjust, Setting, Display, Configuration, Trigger2, or Memory. 4.Press the MENUkey to exit. The MENU disappears. Adjust the picture to suit own preference by using the Picture Adjust feature. ❖For a video signal input, the following adjustments can be made: NOTE: - You cannot adjust Tint in Component signal (YC...
Page 26
ENGLISH 22 By adjusting this Fine Menu, you can make fine picture adjustment. Note: There are some parameters can not adjust according to input signal. ❖Luminance H Detail Gain(Horizontal Detail Processing Gain) : This menu allows the users to set the horizontal detail processing gain. H Detail Threshold(Horizontal Detail processing Threshold) : This menu allows the users to set the lower threshold for horizontal detail processing. H Edge Gain(Horizontal Large Edge Enhancement Gain) : This menu allows...
Page 27
ENGLISH 23 ❖Sub Control Contrast Red : This menu allows the users to set the contrast for red. Contrast Green : This menu allows the users to set the contrast for green. Contrast Blue : This menu allows the users to set the contrast for blue. Brightness Red : This menu allows the users to set the brightness for red. Brightness Green : This menu allows the users to set the brightness for green. Brightness Blue : This menu allows the users to set the brightness for blue. ❖Miscellaneous DCDi : This menu...
Page 28
The following settings can be made: Aspect Full, Normal, Through, Zoom Cinema Auto, Off Cinema mode : The 3-2 pull down for NTSC and the 2-2 pull down for PAL Black Setup 0IRE, 7.5IRE Black level adjustment, for adjusting black level by a video source. NOTE : Black Setup is not available for IEEE1394 signal : AUX in signal. Component Auto, NTSC, PAL, 480p, 540p, 576p, 720p, 1035i, 1080i Video System Auto, NTSC, PAL, SECAM RGB System Auto, NTSC, PAL, 480p, 540p, 576p, 720p, 1035i, 1080i DVI System RGB,...
Page 29
ENGLISH 25 The following adjustments can be made: –Keystone H, V Adjust trapezoid image to rectangle image. –Auto Adjust Yes : For RGB IN signal, Picture Shift V and H, Size V and H, and Phase are adjusted automatically. No : If something wrong with AUTO Adjust, select No, and adjust Size V, Size H, Picture Shift H, Picture Shift V, and/or Phase manually. Use 1/2key to select “Yes”, and press the ENTERkey. –Picture Shift V, H Adjust the position of the picture. H adjusts the horizontal position of the...
Page 30
The following adjustments can be made: –OSD Position (16:9 / 4:3) Select OSD position from 16:9 or 4:3. –Reset Lamp Life Lamp Life must be reset immediately if the lamp is replaced. Select “Reset Lamp Life” from Config menu. The menu shown below is displayed. Again, select “Yes”, and press the ENTERkey. Then the lamp life is initialized. –Reset All All settings are reset to the factory default settings except the lamp life. When the user selects “Yes”, the following message appears: Again, select “Yes”,...