Home > Marantz > Projector > Marantz Vp 12s2 DLP Projector User Manual

Marantz Vp 12s2 DLP Projector User Manual

Here you can view all the pages of manual Marantz Vp 12s2 DLP Projector User Manual. The Marantz manuals for Projector are available online for free. You can easily download all the documents as PDF.

Page 11

ENGLISH
7
1.Open the Battery cover.
2.Insert two AA size batteries.
Make sure the polarities match the + and – marks inside
the battery compartment.
3.Close the battery cover.
Preparing the Remote ControllerCAUTION
–The available battery types are limited: manganese dry cell
and alkaline dry cell.
–Do not mix different battery types.
–Do not mix old and new batteries.
–Only batteries of the same type are to be used.
–Remove exhausted batteries from the Remote Controller.
–Do not attempt to recharge...

Page 12

ENGLISH
8
❖When making connections be sure to:
•Turn off all equipment before making any connections.
•Use the proper cables for each connection.
•Insert the plug properly. Any plugs that are not fully inserted often generate a noise.
❖When pulling out a cable:
•Be sure to grab the plug, not the cable itself.
Connect the supplied AC power cord into the AC IN socket of
the projector.
The STANDBY indicator lights up and the projector goes into
the standby mode.
Note :Make sure the AC power cord is firmly...

Page 13

ENGLISH
9
You can connect this projector to HD-Video /PC using RGB IN port, or Satellite /Cable Tuner /PC using DVI-D IN port.
1.Connect one end of the RGB cable to the RGB IN port, or one end of the DVI-D cable to the DVI-D IN port on the projector.
2.Connect the other end to the corresponding port on a HD-Video, Satellite, Cable Tuner or personal computer.
Note :When projecting a video image from a device connected to the DVI-D terminal, follow the procedure below.
1. Turn on power of this unit. (...

Page 14

ENGLISH
10
1.Connect the supplied AC power cord. (P.8)
2.Press the POWER ONkey on the remote controller or the POWERkey on the projector.
The POWER ON indicator lights up.
Project an image on the screen roughly at first.
1.Turn the Zoom ringand adjust to the desired size within
the zoom range.
2.Turn the Focus ringuntil the image on the screen
becomes clear.
You can adjust the image position with the Lens Shift knob.
❖Turn the Lens Shift knob to clockwise : The image goes up.
Adjusting the Image...

Page 15

ENGLISH
11
❖Turn the Lens Shift knob to counterclockwise : The image goes down.
Adjust the height of the image by raising the projector with the adjustment lever.1.Operate the adjustment lever for releasing the adjustable feet.  And lift the projector up carefully.
2.Remove your hands from the lever. Once the adjustable feet have locked in position, release the projector.
3.If the screen is at an angle, the adjusters can be used to adjust the angle of the image.
❖Returning the Projector to its Initial...

Page 16

ENGLISH
12
2.Turn the Focus ringto make an adjustment.
Adjust the focus for the sharpest image possible to obtain, using focus pattern.
3.Press the FOCUSkey again to clear off the pattern.
When the projecting image is a trapezoid, correct it in Keystone-V and/or Keystone-H in the Display Menu.
See “Display”. (
P.25)
Keystone Correction
❖Keystone-V
(Electronic vertical keystone correction)❖Keystone-H
(Electronic horizontal keystone correction)
Note :Electronic horizontal keystone correction works...

Page 17

ENGLISH
13
❖Installing on a tabletop
❖Mounting on the ceiling
CAUTION
–For ceiling installation, consult with Marantz authorized dealer.
–Do not look into the lens when the projector is turned on.  It could damage your eyesight.
EXT-81
MOUNT12
Recommended Setting
INSTALLATION
Screen
Screen upper end
Screen
Range from light axis to upper end
Light axis (center)
Height from installing level to light axis
Installing level
Screen size (vertical)
Screen lower end
Projection distance
lens head
Lens shift range...

Page 18

ENGLISH
14
❖16 : 9 Screen
In case of displaying the 16:9 picture on
the whole of the 16:9 screen.
❖4 : 3 Screen
In case of displaying the 16:9 picture on
the whole of the 4:3 screen.
Diagonal Width Height Minimum Maximum
inch inch inch inch inch
4032 24
6048 36
7056 42
7257 5/8 43 3/16
8064 48
8467 3/16 50 3/8
9072 54
10080 60
11088 66
12096 72
150120 90
170136 102
180144 108
200160 120
250200 150
To calculate the installation measurement (unit : inch)
Minimum = (30.49 x Screen Size - 47.6) x 1000...

Page 19

ENGLISH
15
❖16 : 9 Screen
In case of displaying the 16:9 picture on
the whole of the 16:9 screen.
❖4 : 3 Screen
In case of displaying the 16:9 picture on
the whole of the 4:3 screen.
Diagonal Width Height Minimum Maximum
inch mm mm m m
40
60
70
72
80
84
90
100
110
120
150
170
180
200
250
To calculate the installation measurement (unit : m)
Minimum = (30.49 x Screen Size - 47.6) 
Maximum= (35.31 x Screen Size - 47.6)
Note : Tolerance 5% 4:3 Screen Size (1.33:1 Aspect Ration) Projection Distance
± 813...

Page 20

ENGLISH
16
Press the POWER ONkey on the remote controller or the POWERkey on the projector.
The POWER ON indicator lights up.
Switch to the equipment connected to the projector.
Press the INPUT SELECTkey on the projector or the COMPONENTkey, S-VIDEOkey, VIDEOkey, RGBkey or AUXkey on the
remote controller.
You can select 4 kinds of ASPECT mode using remote controller.
Press the FULLkey, NORMALkey, ZOOMkey, or THROUGHkey on the remote controller.
You can select the mode using on-screen menu, too.
Select a...
Start reading Marantz Vp 12s2 DLP Projector User Manual

Related Manuals for Marantz Vp 12s2 DLP Projector User Manual

All Marantz manuals