Marantz Vp 12s2 DLP Projector User Manual

							ENGLISH
17
•Press the ZOOMkey, the NORMALkey or the FULLkey on the remote controller for the 4:3 aspect ratio video source.
•Press the FULLkey on the remote controller for 16:9 aspect ratio video source, such as 1080i, 1035i, and 720p video systems.
•Press the FULLkey on the remote controller for the squeezed video source.
See “Setting”. (
P.24)
The Screen Images in a 16:9 screen
❖Original Source Image
❖Full mode
The 16:9 squeezed image is displayed with the correct
aspect.
❖Normal mode
❖Zoom mode
The 4:3 image is enlarged horizontally.
The picture in normal ratio 4:3 is displayed.
The picture in normal ratio 4:3 is enlarged vertically and
horizontally (with same ratio) to the screen size
4 : 3  video source16 : 9  video source
❖Through mode
It shows an image when the video source has the same resolution to RGB/video signal with 720 or less vertical pixel number. 
						

							ENGLISH
18
•Press the ZOOMkey, the NORMALkey or the FULLkey on the remote controller for the 4:3 aspect ratio video source.
•Press the FULLkey on the remote controller for 16:9 aspect ratio video source, such as 1080i, 1035i, and 720p video systems.
•Press the FULLkey on the remote controller for the squeezed video source.
See “Setting”. (
P.24)
The Screen Images in a 4:3 screen
❖Original Source Image
❖Full mode
The 16:9 squeezed image is displayed with the correct
aspect.
❖Normal mode
❖Zoom mode
The 4:3 image is enlarged horizontally.
The picture in normal ratio 4:3 is displayed.
The picture in normal ratio 4:3 is enlarged vertically and
horizontally (with same ratio) to the screen size
4 : 3  video source16 : 9  video source
❖Through mode
It shows an image when the video source has the same resolution to RGB/video signal with 720 or less vertical pixel number. 
						

							ENGLISH
19
1.Press the STANDBYkey on the remote controller or the POWERkey on the projector.
2.The fan continues to run for a while to reduce internal heat. The POWER ON indicator flashes in blue and no key will be
active. After about one minute of cooling has been done, the unit turns off and the STANDBY indicator lights up.
Notice: Do not pull out the AC power cord until the projector turns in standby mode.
Notice :
- Do not pull out the power cord suddenly in the state of “POWER ON. It can cause a breakdown.
- When a WARNING indicator lit up or blinks in red, pull out the AC power cord after checking that the fan has stopped.
- The projector will not be turned on if the POWER ONkey on the remote controller or the POWERkey on the projector is
pressed immediately after turning off.  Press the POWER ONkey on the remote controller or POWERkey on the projector
after the projector turns into standby mode.
To Turn off the Power 
						

							ENGLISH
20
Picture Adjust
Contrast Main Menu
Item
Main Menu
Item 0 100
Brightness 0 63
Color 0 100
Sharpness 0 31
Tint R50 G50
Noise Reduction 0 63
Color Temp.  (Temperature) L M H
Fine Menu
Setting
Aspect
Lamp modeHigh / Low
Cinema Auto / Off
Black Setup 0IRE / 7.5IRE
High Bright On / Off
Component
Video System
RGB System
Full
Normal
Through
Zoom
Auto
NTSC
PA L
480p
540p
576p
720p
1035i
1080i
Auto
NTSC
PA L
480p
540p
576p
720p
1035i
1080i
Auto
NTSC
PA L
SECAM
Display
Keystone V  (Vertical)
Keystone H (Horizontal)
Auto Adjust
Picture Shift V (Vertical) Down Up
Size V  (Vertical) Small Large
Picture Shift H (Horizontal) Left Right
Small LargeSize H (Horizontal)
Backward ForwardPhase
LuminanceH Detail Gain
H Detail Threshold
H Edge Gain
H Edge Threshold
V Detail Gain
V Detail Threshold
V Edge Gain
V Edge Threshold
Sub ControlContrast Red
Contrast Green
Contrast Blue
Brightness Red
Brightness Green
Brightness Blue
ChrominanceH Edge Gain
H Edge Threshold
V Edge Gain
Enhancement
Delay
MiscellaneousDCDi
FRC
CCS
VCR Mode
DVI SystemRGB
Y PB PR
Y CB CR
Config (Configuration)
OSD Position
Ceiling On / Off
Rear On / Off
Reset Lamp Life Yes / No
Reset All Yes / No
Language
16 : 9
4 : 3
English
German
French
Spanish
Italian
Portuguese
Trigger 2Full On / Off
Normal On / Off
Through On / Off
Zoom On / Off
MemoryTheater 1 / 2 / 3 / Default
1 / 2 / 3 / Default
1 / 2 / 3 / Default
Standard
Dynamic
1 / 2 / 3 / Default
User
Yes / No
Fine Menu
031
031
031
031
031
031
031
063
031
031
031
031
0 255
0 255
0 255
0 255
0 255
0 255
0+3 –3
On / Off
Auto / On
On / Off
On / Off
Menu Structure
OPERATIONS 
						

							Refer to the on-screen menu for making various adjustments and settings. (P.20)1.Press the MENUkey. The MENU appears.
2.Use 3/4/1/2keys to select a menu item.
3.Make adjustments in Picture Adjust, Setting, Display, Configuration, Trigger2, or Memory.
4.Press the MENUkey to exit. The MENU disappears.
Adjust the picture to suit own preference by using the Picture Adjust feature.
❖For a video signal input, the following adjustments can be made:
NOTE:
- You cannot adjust Tint in Component signal (YC
BCR/YPBPR)
or PAL format signal.
- If User Memory is set to default, Picture Adjust cannot be
selected. To select Picture Adjust, set User Memory to
either 1 to 3.
See “Memory”. (
P.28)
❖Setting the Picture Adjust Menu
1.Use 1/2key to adjust.
2.Use 3key to go back to the menu item.
❖Contrast
❖Color Temp. (Temperature)
H : Make white color bluer.
M : Make white color less blue. This setting is approximately 6500 Kelvin.
L : Make white color redder.
Color Temp.LowMiddleHigh
Contrast 50
2.
1.2.
1.
Picture Adjust
2.
1, 4
1, 4 2.
Picture Adjust
Setting
Display
Config
Trigger 2
MemoryContrast
Brightness
Color
Sharpness
Tint
Noise Reduction
Color Temp.
Fine Menu50
44
64
6
0
0
Middle
Using On-Screen Menu
ENGLISH
21
Item
Contrast
Brightness
Color
Sharpness
Tint
Noise Reduction
Color Temp. (Color Temperature)
Adjustments
0 100
Weak Strong
063
Dark Bright
0 100
Light Deep
031
Soft Sharp
R50 G50
Purple Green
063
Weak Strong
LMH
Red Blue 
						

							ENGLISH
22
By adjusting this Fine Menu, you can make fine picture adjustment.
Note: There are some parameters can not adjust according to input signal.
❖Luminance
H Detail Gain(Horizontal Detail Processing Gain)
: This menu allows the users to set the horizontal detail processing gain.
H Detail Threshold(Horizontal Detail processing Threshold)
: This menu allows the users to set the lower threshold for horizontal detail processing.
H Edge Gain(Horizontal Large Edge Enhancement Gain)
: This menu allows the users to set the horizontal large edge enhancement.
H Edge Threshold(Horizontal Large Edge Enhancement Threshold)
: This menu allows the users to set the lower threshold for horizontal large edge enhancement.
V Detail Gain(Vertical Detail Processing Gain)
: This menu allows the users to set the vertical detail processing gain.
V Detail Threshold(Vertical Detail Processing Threshold)
: This menu allows the users to set the lower threshold for vertical detail processing.
V Edge Gain(Vertical Large Edge Enhancement Gain)
: This menu allows the users to set the vertical large edge enhancement.
V Edge Threshold(Vertical Large Edge Enhancement Threshold)
: This menu allows the users to set the lower threshold for vertical large edge enhancement.
Note :If it is hard to see the effect, make the sharpness higher and adjust it.
❖Chrominance
H Edge Gain(Horizontal Large Edge Enhancement Gain)
: This menu allows the users to set the horizontal large edge enhancement.
H Edge Threshold(Horizontal Large Edge Enhancement Threshold)
: This menu allows the user to set the lower threshold for horizontal large edge enhancement.
V Edge Gain(Vertical Large Edge Enhancement Gain)
: This menu allows the users to set the vertical large edge enhancement.
Enhancement(Enhancer Gain)
: This menu allows the users to set the over all enhancement level.
Delay
: This menu allows the users to set the delay.
Luminance
Chrominance
Sub Control
MiscellaneousH Edge Gain
H Edge Threshold
V Edge Gain
Enhancement
Delay3
6
8
6
0
Luminance
Chrominance
Sub Control
MiscellaneousH Detail Gain
H Detail Threshold
H Edge Gain
H Edge Threshold
V Detail Gain5
11
5
9
5
V Detail Threshold
V Edge Gain
V Edge Thresh.6
4
5
Fine Menu
Item
H Detail Gain
H Detail Threshold
H Edge Gain
H Edge Threshold
V Detail Gain
V Detail Threshold
V Edge Gain
V Edge ThresholdAdjustments
031
031
031
031
031
031
031
063
Item
H Edge Gain
H Edge Threshold
V Edge Gain
Enhancement
DelayAdjustments
031
031
031
031
– 30+ 3 
						

							ENGLISH
23
❖Sub Control
Contrast Red
: This menu allows the users to set the contrast for red.
Contrast Green
: This menu allows the users to set the contrast for green.
Contrast Blue
: This menu allows the users to set the contrast for blue.
Brightness Red
: This menu allows the users to set the brightness for red.
Brightness Green
: This menu allows the users to set the brightness for green.
Brightness Blue
: This menu allows the users to set the brightness for blue.
❖Miscellaneous
DCDi
: This menu allows the users to control DCDi.
FRC (Frame Rate Conversion)
Auto : Frame Rate Conversion function is basically off. However FRC turns on automatically depending on vertical
frequency of input signal.
ON : Frame Rate Conversion function is “ON”. (60Hz fixed)
CCS (Cross Color Suppressor Function)
ON : Cross color suppressor enabled.
OFF : Cross color suppressor disabled. For like progressive scan DVD players, where most of the source material does
not contain any cross color, use this mode.
VCR Mode
ON : A projector is forced into the intra-field only deinterlacing mode.
OFF : A projector is used with external field memories and operates in the full set of deinterlacing modes, i.e., motion
adaptive video deinterlacing and full frame film source deinterlacing using 3:2 pulldown detection (2:2 pulldown
for 625/50 sources).
Luminance
Chrominance
Sub Control
MiscellaneousDCDi
FRC
CCS
VCR ModeOn
Auto
Off
Off
Luminance
Chrominance
Sub Control
MiscellaneousContrast Red
Contrast Green
Contrast Blue
Brightness Red
Brightness Green
Brightness Blue128
128
128
128
128
128Item
Contrast Red
Contrast Green
Contrast Blue
Brightness Red
Brightness Green
Brightness BlueAdjustments
0 255
0 255
0 255
0 255
0 255
0 255
Item
DCDi
FRC
CCS
VCR ModeAdjustments
On Off
Auto On
On Off
On Off 
						

							The following settings can be made:
Aspect Full, Normal, Through, Zoom
Cinema Auto, Off
Cinema mode : The 3-2 pull down for NTSC
and the 2-2 pull down for PAL
Black Setup 0IRE, 7.5IRE
Black level adjustment, for adjusting black
level by a video source.
NOTE : Black Setup is not available for
IEEE1394 signal : AUX in signal.
Component Auto, NTSC, PAL, 480p, 540p, 576p,
720p, 1035i, 1080i
Video System Auto, NTSC, PAL, SECAM
RGB System Auto, NTSC, PAL, 480p, 540p, 576p,
720p, 1035i, 1080i
DVI System RGB, YPBPR, YCBCR
Color space conversion select for DVI input.
RGB: Color Space Conversion is skipped.
YP
BPR: This mode is suitable for HD TV
signal such a 720p, 1080i.
YC
BCR: This mode is suitable for SD TV
signal such a 480i, 480p.
❖Setting the Setting Menu
1.Use 3/4key to adjust.
2.Use 1key to go back to the menu item.
1.
2.1.
2.
Picture Adjust
Setting
Display
Config
Trigger 2
MemoryAspect
Cinema
Black Setup
Component
Video System
RGB System
DVI SystemFull
Auto
0 IRE
Auto
Auto
Auto
RGB
Setting
ENGLISH
24
NTSC(NTSC-3.58): Conventional analog broadcasting used
mainly in USA, Canada, Taiwan, Korea, and
Japan.
PAL(PAL-4.43): Conventional analog broadcasting used
mainly in United Kingdom and Germany.
SECAM: Conventional analog broadcasting used
mainly in France and Russia.
480p: Standard digital broadcasting
540p: Special digital broadcasting 
(for example: RCA DTC100)
576p: Standard digital broadcasting
720p, 1080i: High Definition digital broadcasting
1035i: Japanese Hi-Vision broadcasting 
						

							ENGLISH
25
The following adjustments can be made:
–Keystone H, V
Adjust trapezoid image to rectangle image.
–Auto Adjust
Yes : For RGB IN signal, Picture Shift V and H, Size V and H, and Phase are adjusted automatically.
No : If something wrong with AUTO Adjust, select No, and adjust Size V, Size H, Picture Shift H, Picture Shift V, and/or Phase
manually.
Use 
1/2key to select “Yes”, and press the ENTERkey.
–Picture Shift V, H
Adjust the position of the picture. H adjusts the horizontal position of the picture. V adjusts the vertical position of the picture.
–Size V, H
Adjust the vertical and horizontal size of the picture. 
–Phase
Adjust the phase of the DMD
TMdots and the computer signal input from the RGB IN. Adjust the picture to where it looks
clearest.
NOTE:
- If User Memory is set to default, Picture Shift V, H cannot be selected. To select Picture Shift V, H, set User Memory to either 1 to 3.
See “Memory”. (
P.28)
❖Setting the Display Menu
1.Use 1/2key to adjust.
2.Use 3key to go back to the menu item.
2.
1.2.
1.
Keystone-V (Electronic vertical 
keystone correction)
Keystone-H (Electronic horizontal 
keystone correction)
Auto Adjust
Picture Shift V
Size V
Picture Shift H
Size H
Phase
  
  
  
 
    Item Adjustments
Down
 Small
Left
Small
Backward
Up
Large
Right
Large
Forward
Yes / No
Picture Adjust
Setting
Display
Config
Trigger 2
MemoryKeystone V
Keystone H
Auto Adjust
Picture Shift V
Size V
Picture Shift V
Size H
Phase0
0
50
50
50
50
12
Display 
						

							The following adjustments can be made:
–OSD Position (16:9 / 4:3)
Select OSD position from 16:9 or 4:3.
–Reset Lamp Life
Lamp Life must be reset immediately if the lamp is replaced. Select “Reset Lamp Life” from Config menu. The menu shown
below is displayed.
Again, select “Yes”, and press the ENTERkey. Then the lamp life is initialized.
–Reset All
All settings are reset to the factory default settings except the lamp life.
When the user selects “Yes”, the following message appears:
Again, select “Yes”, and press the ENTERkey.
Ye s N o
Reset All ?
Ye s N o
Reset Lamp Life ?
4 : 3  OSD position16 : 9  OSD position
Picture Adjust
Setting
Display
Config
Trigger 2
MemoryContrast
Brightness
Color
Sharpness
Tint
Noise Reduction
Color Temp.
Fine Menu50
44
64
6
0
0
MiddlePicture Adjust
Setting
Display
Config
Trigger 2
MemoryContrast
Brightness
Color
Sharpness
Tint
Noise Reduction
Color Temp.
Fine Menu50
44
64
6
0
0
Middle
Picture Adjust
Setting
Display
Config
Trigger 2
MemoryLamp Mode
High Bright
OSD Position
Language
Ceiling
Rear
Reset Lamp Life
Reset AllHigh
Off
16:9
English
Off
Off
Configuration
ENGLISH
26
Lamp mode High, Low
High Bright On, Off
High Bright On : Display brightest image.
OSD Position 16:9, 4:3
Language English, German, French, Spanish,
Portuguese, Italian
Ceiling On, Off
On: The picture is reversed horizontally
and vertically.
Rear On, Off
On: The picture is reversed horizontally.
Reset Lamp LifeYes, No
Reset All Yes, No