Lucent Technologies Remote Port Security Device Users Guide

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
RPSD System Administration 
Page 3-41 Command Functions 
3
If the [-] and [ALL] parameters are not used, the messages are displayed in 
ascending order by message sequence number, 20 to a page. “- More to Come 
-” appears at the bottom of the each page except the last page, and “- End of 
List -” appears at the bottom of the last page. Press   to move from page 
to page. When you reach the last page (indicated by “- End of List...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
RPSD System Administration 
Page 3-42 Command Functions 
3
Sample Command and Response
The fields of the Log History screen are:
In the example, KEY20 is a user ID. Where the user ID is followed by information 
in square brackets (as in the fifth message shown above), the information is the 
RPSD User ID number.Message 
Authenti-
cation Code/ 
Sequence 
NumberThe Message Authentication code is generated for each 
entry on the...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
RPSD System Administration 
Page 3-43 Command Functions 
3
When a user’s attempt at access fails (see the fifth message in the example 
above), an access failure status message is generated, indicating the reason for 
the failure. Ta b l e  3 - 2
 lists the codes and status messages and the meaning of 
each failure message. The List Statistics command can also be used to get a 
very brief description for each code (see...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
RPSD System Administration 
Page 3-44 Command Functions 
3
Q—Quit
Syntax and Parameters
Q 
Description
Use the Quit command to terminate an administrative session and return the 
RPSD system to a secure mode. Administrative users must press   twice 
and use a password or passkey to begin a new administrative session.
!Security Alert:
It is recommended that you use the Quit command to terminate all 
administrative sessions to...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
RPSD System Administration 
Page 3-45 Command Functions 
3
R—Remove User
Syntax and Parameters
r  
Description
The Remove User command removes a user from the user table. This prevents 
that user from accessing the Lock or the attendant RMATS channel. The 10 
permanent Lucent Technologies users cannot be removed. If the user is added 
again, the user must reinitialize the Key with new secret information. The user can 
also be...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
RPSD System Administration 
Page 3-46 Command Functions 
3
RS—Reset Statistics
Syntax and Parameters
rs 
Description
Use the Reset Statistics command to reset the access attempts statistics to zero. 
This command does not reset cumulative totals. Use the List Statistics command 
to obtain the access attempts statistics (see instructions on page 3-34).
Sample Command and Response
Parameter Description
rsReset Statistics command...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
RPSD System Administration 
Page 3-47 Command Functions 
3
SC—Set Communications Parameters
Syntax and Parameters
sc  
Description
Use the Set Communications Parameters command to set the communications 
link speed, character length, and parity on the serial port. The default setting is 
9600 baud, eight-bit, no parity. 
Sample Command and Response
Parameter Description
scSet Communications Parameters command
The communications...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
RPSD System Administration 
Page 3-48 Command Functions 
3
ST—Status Display
Syntax and Parameters
st 
Description
Use the Status Display command to display the version, date, time, 
communications parameters, and current status of the RPSD Lock.
Sample Command and Response
The fields of the Status Display screen are:Parameter Description
stStatus Display command
Lucent 
Technologies
 RPSD
/JPLock01The version number of the...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
RPSD System Administration 
Page 3-49 Command Functions 
3
Log IDThe Log ID of the RPSD Lock. To set a Log ID, use the ID Set 
command (see instructions on page 3-31).
Comms Set 
toThe setting of the communications parameters. To change 
the communications parameters, use the Set 
Communications Parameters command (see instructions on 
page 3-14). The default setting is 9600 baud at eight bits, no 
parity.
Current 
StatusThe...

Remote Port Security Device
User’s Guide  555-024-402  Issue 1
October 1996
RPSD System Administration 
Page 3-50 Command Functions 
3
T—Test User
Syntax and Parameters
t  
Description
The Test User command shows the following information:
nA seven-digit pseudo-random code to be matched by a code from the 
specified RPSD Key user 
nWhether the user is currently blocked and/or restricted
Use the seven-digit test response code to check whether the Key has been 
seeded properly with the secret information....