Lucent Technologies Definity Enterprise Communications Server (ECS) CALLMASTER IV Voice Terminal Instructions Manual

  CALLMASTER® IV Voice Terminal User and Installation Instructions
10
Installation Procedures
Use the following procedures to install your CALLMASTER IV voice terminal.
See Figure 3 for the location of the jacks mentioned below.
1Lay the voice terminal face down so the bottom slopes toward you.
2Plug the line cord into the 4-wire LINE jack for 4-wire operation; for 2-wire 
operation, plug the line cord into the 2-wire LINE jack. Press firmly until 
you hear the line cord click.
NOTE: If you plug the line...

  CALLMASTER® IV Voice Terminal User and Installation Instructions
11
FIGURE 3 The LINE Jack, Adjunct Jack, and Routing Channels
Operating Range Requirements
·The total distance between the CALLMASTER IV voice terminal with 
recorder interface active and the recording device should not exceed 200 
feet/60.96 meters.
·The distance between the CALLMASTER IV voice terminal and the PBX 
must NOT exceed the following:
—In 4-wire mode, with 22-gauge or 24-gauge wire, the distance 
between the CALLMASTER IV and...

  CALLMASTER® IV Voice Terminal User and Installation Instructions
12
The 2-Wire/4-Wire Line Adapter
The 2-wire/4-wire line adapter (PEC: 32302; Comcode: 407124114 for a single 
adapter; PEC: 32303 for a package of 25 adapters) is available to 
accommodate situations in which customers need to upgrade from an analog-
type RJ11C jack to an 8-wire RJ45X-type jack. This adapter eliminates the 
need to remove RJ11C jacks which are presently being used and install new 
RJ45X jacks in their place. 
Please read...

  CALLMASTER® IV Voice Terminal User and Installation Instructions
13
     * U-T = “Tip”
       U-R = “Ring”The DCP Line Interface
CONNECTOR BLOCK DCP JACK INTERFACE
Conn. 
Block Pin 
NumberD Inside 
Wire ColorPin Name Signal Description
3 W-O 1 OD1 Balance output from 
telephone (power –48V)
4-wire application
REC-1 Output to Recorder
2-wire application
4 O-W 2 OD2 Balance output from 
telephone (power –48V)
4-wire application
REC-2 Output to Recorder 
2-wire application
5 W-G 3 ID1 Balance input from...

  CALLMASTER® IV Voice Terminal User and Installation Instructions
14
Figure 4 shows how a CALLMASTER IV, in a 4-wire application with Recorder 
Interface, should be configured through the wall jack with the DEFINITY PBX, 
an adjunct power source, and the recording device.
Figure 5 shows the same connections when a CALLMASTER IV is in a 2-wire 
application.
NOTE: Typically, an RJ45X or equivalent wall jack is used in this type of 
configuration. 

  CALLMASTER® IV Voice Terminal User and Installation Instructions
15
FIGURE 4 Connecting the 4-Wire CALLMASTER IV with Recorder Interface to 
the PBX, Adjunct Power Source, and the Recording Device
CALLMASTER IV
Adjunct Power
PBX
Twisted Pair
Wire
4-Pair Cross
Connect
D8W Cord
CALLMASTER IV
Vo i c e
Terminal
House Cable
RJ45X Wall
Jack
W-O (0D1)
O-W (0D2)
W-G (ID1)
G-W (ID2)
W-BR (P1-)
BR-W (P2+)
W-BL (REC1)
BL-W (REC2)
White Connecting Block,
110-Type
Blue Connecting
Block, 110-Type
Recording
Device 

  CALLMASTER® IV Voice Terminal User and Installation Instructions
16
FIGURE 5 Connecting the 2-Wire CALLMASTER IV with Recorder Interface to 
the PBX, Adjunct Power Source, and the Recording Device
CALLMASTER IV
Adjunct Power
PBX
4-Pair Cross
Connect
D8W Cord
CALLMASTER IV
Vo ic e
Terminal
House Cable
RJ45X Wall
Jack
G-W (Unused)
W-G (Unused)
BL-W (U-R)
W-BL (U-T)
BR-W (P2+)
W-BR (P1-)
O-W (REC2)
W-O (REC1)
White Connecting Block,
110-Type
Blue Connecting
Block, 110-Type
Recording
Device 

  CALLMASTER® IV Voice Terminal User and Installation Instructions
17
Testing the Headset or Handset
NOTE: If you are using a handset, use the installation instructions that come 
with the handset kit to install the handset cradle.
1Plug in the headset or the handset, press a call appearance button, and 
listen for dial tone.
·If you do not hear dial tone, press another call appearance button. 
You may also want to check that the cords are connected securely 
at both ends.
Labeling and Installing the...

  CALLMASTER® IV Voice Terminal User and Installation Instructions
18
5Place the designation card that you have filled out over the buttons, and 
then replace the clear cover by gently bending the cover so that the tabs 
at the top and bottom end of the cover can be inserted into the 
corresponding slots on the housing of the voice terminal. See Figure 6.
FIGURE 6 Inserting the Designation Cards
Basic Voice Terminal Operations
The following operations can be used immediately.
Going Off-Hook
NOTE: When...

  CALLMASTER® IV Voice Terminal User and Installation Instructions
19
Raising or Lowering Receive Volume
You can use the Volume control button to raise and lower the receive level 
volume under the following conditions:
·The CALLMASTER IV voice terminal is off-hook, and the headset(s) is 
plugged in.
·The voice terminal is not off-hook on an external speakerphone call.
·No call is ringing.
·You are not in the midst of selecting a personalized ringing pattern.
To raise or lower the receive volume
·To...