Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation And Test For Multi-Carrier Cabinets Manual

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Cable Ductwork 
C-5  
C
Table C-2. Installation Sequence 
Step Group Remarks
1 41 Install basic  d uc twork on eac h c ab inet
2 51 Install c ross-aisle shielded  d uc twork
3 10 or 26 Install I/O c ross-aisle or c ab inet to wall c able troug h
22-25 Install I/O c ross-aisle to wall troug h d uc t
48
or
9Install I/O c ab le rac k c oup ling to rear of c ab inet
or
install I/O c ab le rac k riser to...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Cable Ductwork 
C-6  
C
Figure C-2. Overhead View of a Typical Ductwork LayoutFigure Notes
1. Wall
2. Space for Future Cabinet
3. Plywood Wall and Cross-Connect Field
4. I/O Cable Rack Coupling to Rear of 
Cabinet
5. AC Power Cable Duct6. Shielded Intercabinet Fiber Optic 
Cables
7. I/O Duct to Cross-Connect Field
8. I/O Cross-Isle Trough
9. Front of Cabinets 

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Cable Ductwork 
C-7  
C
Install Intercabinet Shielded Ducts
1. Loosen (d o not remove) the four b olts holding  the d ust c over to the c ab le 
ac c ess hole in the top  of the c abinet.
Figure C-3. Dust Cover Removal
2. Remove the dust cover by sliding it in the direction shown by the arrow in 
Fi g u re  C -3
. Move the d ust c over until it c lears the b olts.
3. Set the c ab inet riser (Fi g u...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Cable Ductwork 
C-8  
C
Figure C-4. Assembly of Intercabinet Shielded Ducts
4. Install risers on any other c ab inets that req uire shield ed -d uc t c onnec tions.
5. Set a shield ed  troug h b etween two c abinet risers. Push d own on the 
troug h so the slots in the end s of the troug h eng age the ears at the 
c orners of the risers. The walls of the troug h g o insid e the walls of the 
risers...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Cable Ductwork 
C-9  
C
9. If a g iven c ab inet is to sup p ort a c ross-aisle shield ed  d uc t, set a 
c ross-aisle riser on the c ab inet riser. Otherwise set a shield ed  c oup ling  on 
the c ab inet riser. In either c ase, p osition the d evic e so the two holes on the 
b ac k wall line up  with the holes on the b ac k wall of the c ab inet riser. Bolt 
the two p iec es tog ether at the holes...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Cable Ductwork 
C-10  
C
Figure C-5. Assembly of Cross-Aisle Shielded Ducts
2. Install c ross-aisle troug hs on any other c abinets req uiring  suc h 
c onnec tions.
3. If there is no troug h to install in one end  of the c ross-aisle riser, press a 
c ross-aisle shield ed  end  c ap  on the unused  end  of the riser. Unlike earlier 
d uc twork, the end c ap  fits either end  of the c ross-aisle...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Cable Ductwork 
C-11  
C
4. Route the ap p rop riate c ab les b etween the c ab inets just c onnec ted .
5. Set the shield ed  c ross-aisle troug h c over on top  of the trough with its sid e 
walls outsid e of the walls of the trough, and  p ress it d own until it 
c omp letely c overs the troug h.
Mating Cross-Aisle Risers to Old Cabinet Risers
The new shield ed  d uc twork is c onstruc ted  so c...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Cable Ductwork 
C-12  
C
Mating Shielded Ducts to Risers
The new shield ed  d uc twork is c onstruc ted  so new c ross-aisle troug hs c an b e 
attac hed  to risers of the former d esig n. They fit outsid e of the old er risers.
To attac h the new shield ed  troug h to a riser, first set it und er the troug h on the 
riser and  install the other side of the trough as alread y d esc rib ed . Lift the...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Cable Ductwork 
C-13  
C
Figure C-8. Install Cross-Aisle I/O Ductwork or I/O Cross-Aisle to Wall 
Trough
NOTE:
If wall troug h is b eing  installed, loc ally p rovid ed  hard ware is req uired  at wall 
end  of d uc t.
Install Cross-Aisle to Wall Trough
Refer to Fi g u re  C - 9 to assemble the d uc twork:
1. Install wall mounting  b rac ket to desig nated  loc ation. Hardware to mount 
b rac ket...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Cable Ductwork 
C-14  
C
2. Use thread -forming  sc rews to attac h the 3-hole fac e of the ang le b rac ket 
to the I/O trough.
3. Attac h the ang le b rac ket to the 6-hole fac e of the c ross-aisle b rac ket using  
three 10-24 X 3/4 inc h sc rews, c onnec ted to nuts and  washers throug h the 
b ottom holes.
4. Attac h the I/O c able d uc t to the c ross-aisle b rac ket using  the 
thread...