Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Administrators Guide

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
727 IP Trunk Configuration Manager 
17
The Telephony property page contains the following parameters:
Parameter Description
Telephony Board 
InstalledThese display-only fields show:
Number of Boards: 1
Type of Board: IP Trunk
Trunk Control Protocol: IP Trunk - T1
IP Trunk - E1
DSP Resources 
Installed
nNumber of Boards: Identifies the number of DSP cards installed 
in the server.
nType of Board: Identifies...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
728 IP Trunk Configuration Manager 
17
Telephony Advanced dialog box
Use the Telephony Advanced dialog box to adjust additional telephony 
parameters. 
The Telephony Advanced dialog box contains the following parameters: Maximum Digits to 
Be CollectedAllows you to set the maximum number of digits that the IP trunk 
application will accept from the switch for an outgoing call.
If this value is less than the...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
729 IP Trunk Configuration Manager 
17
Voice/Fax dialog box
Use the Voice/Fax property page to view information about, and configure some 
of the capabilities of, the DSP subsystem.
The Voice/Fax property page contains the following parameters: Time Out
1 to 600,000
Allows you to set the maximum time that can elapse with no 
stimulus from the network before call will be disconnected with 
reason of...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
730 IP Trunk Configuration Manager 
17
Internet dialog box
Use the Internet dialog box to configure your connection to an IP network. Adjust 
these parameters as needed for optimal performance. 
nDTMF Duration: Sets the DTMF (Dual Tone Multi-frequency) 
duration for communication with an H.323 client.
Valid values: 
150 to 15000 (milliseconds)
nDTMF Silence Duration: Sets the silence duration interval...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
731 IP Trunk Configuration Manager 
17
The Internet dialog box contains the following parameters:
Parameter Description
Lucent Gateway 
ProtocolnSignaling Port: Displays the initial port number (5000) used for 
call setup. Display only.
nSetup Time-out (ms): Allows you to set the number of 
milliseconds to wait before canceling a call attempt while trying 
to set up the Internet connection.
If the call setup...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
732 IP Trunk Configuration Manager 
17
Dial/Routing Plan dialog box
The Dial/Routing Plan dialog box controls:
nhow the IP trunk application manipulates the digits it receives for outgoing 
and incoming calls
nthe IP addresses to which outgoing calls are routed
nthe remote sites that can access the DEFINITY ECS application on your 
switch
The Dial/Routing Plan dialog box contains the following parameters:...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
733 IP Trunk Configuration Manager 
17
Routing Info - 
Terminating Dial 
PlannEntry Type: Sets whether or not incoming calls are accepted. 
The default value is Accept. If you set this to Reject, then 
incoming calls are not accepted.
nSearch Digits: See the Dial/Routing Plan Worksheets.
nReplace Digits: See the Dial/Routing Plan Worksheets
nLine Number: In non-DCS configurations, enter Any. 
For DCS...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
734 IP Trunk Configuration Manager 
17
Service Logs dialog box
Use the Service Logs dialog box to configure service logging options for the 
DEFINITY ECS application. 
The Service Logs dialog box contains the following parameters: Remove Allows you to remove the name of an DEFINITY ECS application 
connected to your network. Allows you to remove originating and 
terminating dial/routing plan information and...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
735 IP Trunk Configuration Manager 
17
QoS dialog box
Use the Quality of Service (QoS) dialog box to configure the quality of service 
options for the DEFINITY ECS connections to remote sites. Error Messages Shows you that the logging of error or warning messages into the 
Windows NT Event Viewer is on. Display-only.
When this option is on, you can use the Windows NT Event Viewer 
to view the reported errors...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1
April 2000
Screen reference 
736 IP Trunk Configuration Manager 
17
The Quality of Service dialog box contains the following parameters:
Parameter Description
Line Pool ID Allows you to specify an integer between 1 and 999 that identifies a 
logical group (pool) of lines. The lines consist of trunk groups that 
emulate T1 (robbed-bit) or E1 (common-channel) channels. No 
ISDN connections can be placed in the trunk groups that make up...