LG Avs2400 Owners Manual

Preparation11
2
Preparation
NOTE
OSD lock / u\block fu\a\bctio\b 
You can lock the cur\Brent control settings, so that they cannot be inadvertently changed.
1.  Press and hold the ME\BNU button for several seconds. The message “OSD LOCKED” should appear.
2.  You can unlock the O\BSD controls at any time by holding the MENU \Bbutton for several seconds. The message “OSD 
UNLOCKED” should appear.
i  Monitor power button: Turns the monitor on and off. The camera and system power are not turned off by the...

12Preparation
2
Preparation
Remote Control
This remote control provides wireless control of Video conference system functions and enables y\Bou to navigate the user 
interface, place and receive calls. (You cannot control the monitor using this remote control)
ButtonDes\friptionButtonDes\fription
Use this button when the 
system receives a call or to 
manually make a call.
Use this button to mute the 
microphones of the near\B end 
system.
Use this button when you 
want to hang up.
Use this button to...

Installation13
3
Installation
Connections
 C\fUTION
Before setting up the moni\Btor, ensure that the power to the monitor, the computer system and other attached\B devices are 
turned off. 
\fttaching the stand
1.  Lay the VCS with the screen side down on a flat surface.
 C\fUTION
Lay a foam mat or soft protective cloth on the surface and then lay the VCS carefully to prevent the camera from breaking 
and protect the screen from damage.
2. Make sure to assemble the front and rear side of the stan\Bd....

14Installation
3
Installation
 C\fUTION
Do not attempt to tighten a screw too tightly. If you do, the thread groove or the grip of the locking nut may become 
damaged. 
Tighten a screw to fix a monitor on the stand base\B so that it does not \Bseparate. This may cause an acciden\Bt.
4.  Once assembled, lift the monitor up carefully and face the\B front side.
 C\fUTION
Do not make the monitor stand by holding the camer\Ba. It can be broken and damaged.
Disassembling the stand
1.  Place the VCS with its...

Installation15
3
Installation
Connecting to a PC
This VCS supports the Plug & Play feature and has built-in speakers.
Connect the VCS according to your PC. Refer to the following table.
HDMID-SUB
Video O (Digital) O (\fnalog)
\fudio O (Digital) X
HDMI connection
Transmits the digital video and audi\Bo signals from your PC to the Monitor set. Connect the PC and the Monitor set with the 
HDMI cable as shown in the following illustrations. 
\bhen using the HDMI \s\fable
BroadbandService
 

16Installation
3
Installation
D-SUB connection
Transmits the analog \Bvideo signal from your PC to the Monitor set. Connect the PC and the Monitor set with the suppl\Bied D-sub 
15 pin signal cable as shown in the following illustrations.
\bhen using the D-SUB \fable
BroadbandService 

Installation17
3
Installation
Connecting Network
Connect the L\fN port on the rear of the VCS to your network using the optional\B L\fN cable. This device has two L\fN ports. One 
of them is for network and the other is f\Bor PC. If you connect the PC as shown below, you can use the network on the PC and 
VCS at the same time. 
Network \fonne\ftion
BroadbandService
Connecting Power
Connect the power cable as shown in the following illustrations.
Power \fonne\ftion
BroadbandService
 C\fUTION
You must...

18Installation
3
Installation
Connecting Headphones
Connect a headphone cable\B to the headphone jac\Bk at the bottom of the VCS.
Headphone \fonne\ftion
BroadbandService
Connecting a Microphone
Connect a microphone to the microphone jack at the b\Bottom of the VCS. To use the external microphone, you have to set the 
[\fctive Microphone] option to “Microphone In” on the Admi\bist\fato\f P\fefe\fe\bces : Audio setup menu.
Mi\frophone \fonne\ftion
BroadbandService
 

Installation19
3
Installation
\fttaching the back cover
\fttach the back covers when all of the\B connections are made as shown in the following illustrations.  
Atta\fhing the ba\fk \fover
\fdjusting the angle of the Monitor and camera
\ffter installation, adj\Bust the angle of the \BMonitor and camera in v\Barious ways for maximum comfort. 
It is recommended that the t\Bilt angle of the mon\Bitor and camera shou\Bld not exceed the degrees below in order to maintain an 
ergonomic and comfortable viewing...

20Installation
3
Installation
Initial settings for VCS
When you access the VCS for the first time, the Initial setting screen appears. Select a language and cu\Bstomize the basic settings.
1. Turn on the unit. System booting will com\Bmence. The logo image will\B be displayed during the system booting.
2. When the booting is \Bcomplete the initial configu\Bration menu will be\B displayed. 
3. Set the language.
3-1.  Select your language using\B the wsad buttons and press OK button.
3-2. Press  button to...