LG Avs2400 Owners Manual

							Preparation11
2
Preparation
NOTE
OSD lock / u\block fu\a\bctio\b 
You can lock the cur\Brent control settings, so that they cannot be inadvertently changed.
1.  Press and hold the ME\BNU button for several seconds. The message “OSD LOCKED” should appear.
2.  You can unlock the O\BSD controls at any time by holding the MENU \Bbutton for several seconds. The message “OSD 
UNLOCKED” should appear.
i  Monitor power button: Turns the monitor on and off. The camera and system power are not turned off by the monitor 
power button. You can turn the camera and sy\Bstem power off by using the Main power switch.
Rear of the VCS
	 j	 k	l	m	 n	 o	
 p	 q	r	 \f
j	Power cord Inlet (\fC IN): Connects the power plug.
k Main power switch: Turns the unit on and o\Bff. You must tu\f\b the u\bi\at o\b usi\bg the mai\b \apowe\f switch afte\f 
co\b\becti\bg the powe\f cable. You can use this button to reset the system. 
l	L\fN port: Connects the L\fN cable for this system.
m	PC (L\fN) port: Connects the L\fN cable between the VCS and your PC. 
n	HDMI port: Connects the VCS and the PC with a\B HDMI cable.
o	D-SUB port: Connects the VCS and the PC with th\Be D-SUB cable.
p	Speaker set: Two speakers are built-in.
q	Microphone jack: Connects an external microphone.
r	Headphone jack: Connects an external speaker device.
\f	LOCK: Connects the Kensington security system cable between the VCS and a large object such as a desk.
 
						

							12Preparation
2
Preparation
Remote Control
This remote control provides wireless control of Video conference system functions and enables y\Bou to navigate the user 
interface, place and receive calls. (You cannot control the monitor using this remote control)
ButtonDes\friptionButtonDes\fription
Use this button when the 
system receives a call or to 
manually make a call.
Use this button to mute the 
microphones of the near\B end 
system.
Use this button when you 
want to hang up.
Use this button to select the 
near or far end ca\Bmera.
Displays the directory menu.Use this button to change the 
screen layout. 
Return to the previous mode.This button is not available.
Displays the system menu.Use this button to set the far 
end camera preset or display 
the submenu of the d\Birectory 
menu.
• Move to the next page on 
the current screen.
• This button behaves as 
backspace when you 
enter text or numbers 
manually.
Use this button to adjust the 
volume in a call.
• wsad: Select or move 
between the menu 
options.
• OK: Confirms menu 
selections.
Use this button to adjust the 
zoom of the far-end camera 
with zoom function.
Use this button to return to 
the main screen.
Use these buttons to input 
text or numbers. 
Battery Installation
Open the battery cover, replace batteries (1.5 V \f\f\f) matching 3 and 2 ends to the label inside \Bthe compartment and then 
close the battery cover. 
 C\fUTION
Do not mix old and n\Bew batteries, this may damage the remote control.
 
						

							Installation13
3
Installation
Connections
 C\fUTION
Before setting up the moni\Btor, ensure that the power to the monitor, the computer system and other attached\B devices are 
turned off. 
\fttaching the stand
1.  Lay the VCS with the screen side down on a flat surface.
 C\fUTION
Lay a foam mat or soft protective cloth on the surface and then lay the VCS carefully to prevent the camera from breaking 
and protect the screen from damage.
2. Make sure to assemble the front and rear side of the stan\Bd. Push it into the VCS body as shown in the following illustration.
3. Turn the Stand locking screw clockwise to tighten. Do not over tighten.
3
Installation
  
						

							14Installation
3
Installation
 C\fUTION
Do not attempt to tighten a screw too tightly. If you do, the thread groove or the grip of the locking nut may become 
damaged. 
Tighten a screw to fix a monitor on the stand base\B so that it does not \Bseparate. This may cause an acciden\Bt.
4.  Once assembled, lift the monitor up carefully and face the\B front side.
 C\fUTION
Do not make the monitor stand by holding the camer\Ba. It can be broken and damaged.
Disassembling the stand
1.  Place the VCS with its front facing downward on a soft cloth.
2. Turn the Stand locking screw counterclockwise to disconnect the stand base from the monitor.
Using the Kensington security system (optional)
The Kensington security system connector is located at the rear of the VCS. Connect the Kensington security system cable 
between the VCS and a table.
NOTE
The Kensington security system is optional. You can obtain additi\Bonal accessories from your local dealer.
 
						

							Installation15
3
Installation
Connecting to a PC
This VCS supports the Plug & Play feature and has built-in speakers.
Connect the VCS according to your PC. Refer to the following table.
HDMID-SUB
Video O (Digital) O (\fnalog)
\fudio O (Digital) X
HDMI connection
Transmits the digital video and audi\Bo signals from your PC to the Monitor set. Connect the PC and the Monitor set with the 
HDMI cable as shown in the following illustrations. 
\bhen using the HDMI \s\fable
BroadbandService
 
						

							16Installation
3
Installation
D-SUB connection
Transmits the analog \Bvideo signal from your PC to the Monitor set. Connect the PC and the Monitor set with the suppl\Bied D-sub 
15 pin signal cable as shown in the following illustrations.
\bhen using the D-SUB \fable
BroadbandService 
						

							Installation17
3
Installation
Connecting Network
Connect the L\fN port on the rear of the VCS to your network using the optional\B L\fN cable. This device has two L\fN ports. One 
of them is for network and the other is f\Bor PC. If you connect the PC as shown below, you can use the network on the PC and 
VCS at the same time. 
Network \fonne\ftion
BroadbandService
Connecting Power
Connect the power cable as shown in the following illustrations.
Power \fonne\ftion
BroadbandService
 C\fUTION
You must tu\f\b the u\bi\at o\b usi\bg the 
mai\b powe\f switch afte\f co\b\becti\bg 
the powe\f cable.
 
						

							18Installation
3
Installation
Connecting Headphones
Connect a headphone cable\B to the headphone jac\Bk at the bottom of the VCS.
Headphone \fonne\ftion
BroadbandService
Connecting a Microphone
Connect a microphone to the microphone jack at the b\Bottom of the VCS. To use the external microphone, you have to set the 
[\fctive Microphone] option to “Microphone In” on the Admi\bist\fato\f P\fefe\fe\bces : Audio setup menu.
Mi\frophone \fonne\ftion
BroadbandService
 
						

							Installation19
3
Installation
\fttaching the back cover
\fttach the back covers when all of the\B connections are made as shown in the following illustrations.  
Atta\fhing the ba\fk \fover
\fdjusting the angle of the Monitor and camera
\ffter installation, adj\Bust the angle of the \BMonitor and camera in v\Barious ways for maximum comfort. 
It is recommended that the t\Bilt angle of the mon\Bitor and camera shou\Bld not exceed the degrees below in order to maintain an 
ergonomic and comfortable viewing position.
• Camera tilt range : -\B20° (down) to 20° (up)
• Monitor tilt range: -5° (\Bforward) to 15° 
(backward)
-5° 15° 
-20° 20°
 
						

							20Installation
3
Installation
Initial settings for VCS
When you access the VCS for the first time, the Initial setting screen appears. Select a language and cu\Bstomize the basic settings.
1. Turn on the unit. System booting will com\Bmence. The logo image will\B be displayed during the system booting.
2. When the booting is \Bcomplete the initial configu\Bration menu will be\B displayed. 
3. Set the language.
3-1.  Select your language using\B the wsad buttons and press OK button.
3-2. Press  button to continue. The password setting menu is di\Bsplayed.
4. Set the \fdministrator or User password.
4-1.  Press OK button on the [New Password] option. Enter the password using number buttons and press OK button.
4-2. Press OK button on the [Confirm Password] option. Enter the password again using numb\Ber buttons and press OK 
button.
4-3. Select [Set New Password] option and press OK button. The confirmation message wind\Bow is displayed. Press OK 
button again.
4-4. Press  button to continue. The System identification sett\Bing menu is displa\Byed.
 NOTE
The default administr\Bator password is “1 2 3 4”.