Lexmark X463de User Manual

							Installing a memory card
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the
wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well,
and unplug any cables going into the printer.
Warning—Potential Damage: System board electronic components are easily damaged by static electricity. Touch
something metal on the printer before touching any system board electronic components or connectors.
Note: This task requires a flathead screwdriver.
An optional memory card can be purchased separately and attached to the system board. To install the memory card:
1Access the system board.
2Unpack the memory card.
Note: Avoid touching the connection points along the edge of the card.
3Open the memory card connector latches.
Additional printer setup31
Downloaded From ManualsPrinter.com Manuals 
						

							4Align the notches on the memory card with the ridges in the connector.
1Notches
2Ridges
5Push the memory card straight into the connector until it clicks into place.
Note: After the memory card is installed, make sure the memory card connector latches return to the latched
vertical position and are secure against the card.
6Release the system board access latch, and then close the system board door by lowering the scanner.
7Push in on the screws while rotating them clockwise a quarter turn to lock the system board into place.
Warning—Potential Damage: Make sure the system board is locked to prevent possible damage to the printer if it is
moved. Additional printer setup32
Downloaded From ManualsPrinter.com Manuals 
						

							Installing a flash memory or firmware card
The system board has two connections for an optional flash memory or firmware card. Only one of each may be installed,
but the connectors are interchangeable.
Note: This task requires a flathead screwdriver.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the
wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well,
and unplug any cables going into the printer.
Warning—Potential Damage: System board electronic components are easily damaged by static electricity. Touch
something metal on the printer before touching any system board electronic components or connectors.
1Access the system board.
2Unpack the card.
Note: Avoid touching any electrical components on the card. Additional printer setup33
Downloaded From ManualsPrinter.com Manuals 
						

							3Holding the card by its sides, align the plastic pins on the card with the holes on the system board.
1Plastic pins
2Metal pins
4Push the card firmly into place.
Notes:
The entire length of the connector on the card must touch and be flush against the system board.
Be careful not to damage the connectors.
5Release the latch, and then close the system board door by lowering the scanner. Additional printer setup34
Downloaded From ManualsPrinter.com Manuals 
						

							6Push in on the screws while rotating them clockwise a quarter turn to lock the system board into place.
Warning—Potential Damage:  Make sure the system board is locked to prevent possible damage to the printer if it is
moved.
Installing an Internal Solutions Port
The system board supports one optional Lexmark Internal Solutions Port (ISP). Install an ISP for additional connectivity
options.
Note: This task requires a #2 Phillips screwdriver and a flathead screwdriver.
CAUTION—SHOCK HAZARD: If you are accessing the system board or installing optional hardware or memory
devices sometime after setting up the printer, then turn the printer off, and unplug the power cord from the
wall outlet before continuing. If you have any other devices attached to the printer, then turn them off as well,
and unplug any cables going into the printer.
Warning—Potential Damage: System board electronic components are easily damaged by static electricity. Touch
something metal on the printer before touching any system board electronic components or connectors.
1Access the system board.
2Unpack the ISP and plastic tee.
Note: Avoid touching the components on the card. Additional printer setup35
Downloaded From ManualsPrinter.com Manuals 
						

							3Locate the appropriate connector on the system board.
Note: If an optional printer hard disk is currently installed, then the printer hard disk must first be removed. To
remove the hard disk:
aUnplug the printer hard disk interface cable from the system board, leaving the cable attached to the printer
hard disk. To unplug the cable, squeeze the paddle at the plug of the interface cable to disengage the latch
before pulling the cable out.
Additional printer setup36
Downloaded From ManualsPrinter.com Manuals 
						

							bRemove the screws holding the printer hard disk in place.
cRemove the printer hard disk by pulling it upward to unseat the standoffs.
Additional printer setup37
Downloaded From ManualsPrinter.com Manuals 
						

							dRemove the thumbscrews that attach the printer hard disk mounting bracket to the printer hard disk, and then
remove the bracket. Set the printer hard disk aside.
4Remove the metal cover from the ISP opening.
Additional printer setup38
Downloaded From ManualsPrinter.com Manuals 
						

							5Align the posts of the plastic tee to the holes in the system board, and then press downward until the tee snaps
into place. Be sure each post of the tee has latched completely, and that the tee is seated firmly onto the system
board.
6Install the ISP onto the plastic tee. Angle the ISP over the plastic tee, and then approach the plastic tee so that any
overhanging connectors will pass through the ISP opening in the system board cage.
7Lower the ISP toward the plastic tee until the ISP is seated between the guides of the plastic tee.
Additional printer setup39
Downloaded From ManualsPrinter.com Manuals 
						

							8Insert the long thumbscrew, into the hole closest to the white connector, and turn it clockwise enough to hold the
ISP in place. Do not tighten the thumbscrew at this time.
9Attach the two provided screws to secure the ISP mounting bracket to the system board cage.
10Tighten the long thumbscrew.
Note: Do not overtighten the thumbscrew.
11Insert the plug of the ISP interface cable into the receptacle of the system board.
Note: The plugs and receptacles are color coded. Additional printer setup40
Downloaded From ManualsPrinter.com Manuals