Lexmark X 204 Service Manual

							Diagnostic aids3-21
7011-2xx / 3xx
Disable Scanner
This menu item is used to disable the MFP scanner if it is malfunctioning. The MFP must be powered off and on 
for the new setting’s to take effect. To change the setting, perform the following steps:
1.In the configuration menu, use the arrow keys to scroll to the Disable Scanner menu item.
2.Press .
3.Use the arrow key to scroll to the desired setting. The options are Enable ADF/FB, Disable ADF/FB, 
Disable ADF only, Auto Disabled.
4.Press .
5.Press BACK.
6.Scroll to Exit Config Menu.
7.Press  . The device restarts.
Font Sharpening
This setting is used to set a text point size value below which the high frequency screens will be used when 
printing data. This setting affects only PCL, PostScript and PDF emulators.
setting’s are in the range of 0–150 (24 is the default). For example, if the value is set to 24, then all fonts sized 
24 points or less use the high frequency screens. 
To adjust the Font Sharpening setting, perform the following steps:
1.In the configuration menu, scroll to the Font Sharpening menu item and press  .
2.Use the   or   to increase or decrease the setting’s value. pressing  decreases the value and 
pressing increases the value.
3.Press   to accept the setting.
Reduced Curl
Note:  This only apppears on devices with an instant on fuser.
USB Speed
The USB Speed setting is used to set the throughput of the USB port on the MFP. The setting’s are Auto, which 
is the default, and Full. Full forces the USB port to run at full speed.
Exit Config Menu
With the Exit Config menu item displayed, press Select ( ) to exit the Configuration Menu. The printer 
performs a power-on reset and returns to normal mode. 
						

							3-22Service Manual 7011-2xx / 3xx
SE Menu
Print SE Menus
General
Copyright - Displays copyright information.
Optra Forms mode - On or off
Code Revision Info
Network Code Level - Displays network code level
Network Compile Info - Displays compile information
Printer Code Level - Displays printer code information
Printer Compile Info - Displays compile information
History
Print History
Mark History
History Mode
MAC
Set Card Speed
LAA
Keep Alive
NVRAM
Dump NVRAM
Re-init NVRAM
NPAP
Print Alerts
TCP/IP
netstat -r
arp -a
Allow SNMP Set
MTU
Meditech Mode
Raw LPR Mode
Gather Debug
Enable Debug 
						

							Diagnostic aids3-23
7011-2xx / 3xx
Paper jams
Avoiding jams
The following hints can help you avoid jams:
•Use only recommended paper or specialty media.
For more information, see the Card Stock & Label Guide available on the Lexmark Web site at 
www.lexmark.com/publications.
•Do not load too much paper. Make sure the stack height does not exceed the indicated maximum height.
•Do not load wrinkled, creased, damp, or curled paper.
•Flex, fan, and straighten paper before loading it.
•Do not use paper that has been cut or trimmed by hand.
•Do not mix paper sizes, weights, or types in the same stack.
•Store the paper in an appropriate environment.
•Do not remove trays while the printer is printing. Wait for Load tray  or Ready to appear before 
removing a tray.
•Do not load the manual feeder while the printer is printing. Wait for Load Manual feeder with  to 
appear.
•Push all trays in firmly after loading paper.
•Make sure the guides in the trays are properly positioned, and are not pressing too tightly against the 
paper.
•Make sure all paper sizes and paper types are set correctly in the operator panel menu.
•Make sure all printer cables are attached correctly.  
						

							3-24Service Manual 7011-2xx / 3xx
200 - 201 paper jam
200 paper jam
1.
Remove the tray from the printer.
2.Remove the jam if you can see it. If the jam is not visible, see the instructions for a 201 jam.
3DEF6MNO9WXYZ#2ABC5JKL8TUV01@!.GHI4P
Q
R
S7*
3DEF6MNO9WXYZ#
2ABC5JKL8TUV0
1@!.GHI4P
Q
R
S7* 
						

							Diagnostic aids3-25
7011-2xx / 3xx
201 paper jam
1.
Open the front door, and remove the photoconductor kit and toner cartridge.
2.Lift the flap at the front of the printer, and remove the jammed media.
3.Align and insert the photoconductor kit and toner cartridge.
4.Close the front door.
5.Insert the tray.
6.Press . 
3DEF6MNO9WXYZ#2ABC5JKL8TUV01@!.GHI4PQRS7* 
						

							3-26Service Manual 7011-2xx / 3xx
202 paper jam
1.
Open the front door, and remove the photoconductor kit and toner cartridge.
2.Lift the flap at the front of the printer, and remove the jammed media.
3DEF6MNO9WXYZ#2ABC5JKL8TUV01@!.GHI4PQRS7* 
						

							Diagnostic aids3-27
7011-2xx / 3xx
3.Open the rear door.
4.Remove any jam.
5.Close the rear door.
6.Align and insert the photoconductor kit and toner cartridge.
7.Close the front door.
8.Press . 
						

							3-28Service Manual 7011-2xx / 3xx
241 paper jam
1.
Remove the tray from the printer.
2.Remove the jam.
3.Insert the tray.
4.Press .
3DEF6MNO9WXYZ#2ABC5JKL8TUV01@!.GHI4P
Q
R
S7* 
						

							Diagnostic aids3-29
7011-2xx / 3xx
251 paper jam
A sheet of paper or specialty media failed to feed completely from the manual feeder. Part of it may still be 
visible. If it is visible, then gently pull the jammed sheet from the front of the manual feeder. 
						

							3-30Service Manual 7011-2xx / 3xx
If the sheet is not visible, complete the following steps:
1.Remove the photoconductor kit and cartridge.
2.Lift the flap at the front of the printer, and remove any jammed media.
3.Align and insert the photoconductor kit and toner cartridge.
4.Press .
3DEF6MNO9WXYZ#2ABC5JKL8TUV01@!.GHI4PQRS7*