Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

INTRODUCTION
01-6
SLABS Self Levelling and Anti-Lock 
Brake System
SLS Self Levelling Suspension
SOHC Single Overhead Camshaft 
SPE Single Point Entry
sp.gr Specific gravity
SRO Service Repair Operation
SRS Supplementary Restraint System
std. Standard
synchro Synchronizer or synchromesh
TA Traffic Announcement
TDC Top Dead Centre
TMAP Temperature, Manifold Absolute 
Pressure
TMC Traffic Management Channel
TP Throttle Position
TP Throttle Position 
TV Torsional Vibration
TWC Three-way Catalyst
TXV...

GENERAL INFORMATION
03-1
GENERAL INFORMATION
General Precautions
Dangerous substances
Modern vehicles contain many materials and liquids 
which if not handled with care can be hazardous to 
both personal health and the environment.
WARNING: Many liquids and other substances 
used in motor vehicles are poisonous and should 
under no circumstances be consumed and 
should, as far as possible, be kept from contact 
with the skin. These liquids and substances 
include acid, anti-freeze, asbestos, brake fluid,...

GENERAL INFORMATION
03-2
Safety Instructions
Whenever possible, use a lift or pit when working 
beneath vehicle, in preference to jacking. Chock 
wheels as well as applying parking brake.
Jacking
Always refer to Lifting and Towing Section of this 
manual, prior to jacking vehicle.
Always use the recommended jacking points.
Always ensure that any lifting apparatus has 
sufficient load capacity for the weight to be lifted.
Ensure the vehicle is standing on level ground prior 
to lifting or jacking.
Apply...

GENERAL INFORMATION
03-3
Environmental Precautions
General
This section provides general information  which  can 
help to reduce the environmental  impacts from the 
activities carried out in workshops.
Emissions to air  
Many of the activities that are carried out in 
workshops emit gases and fumes which contribute to 
global warming, depletion of the ozone layer and/or 
the formation of  photochemical smog at ground 
level. By considering how the workshop activities are 
carried out,  these gases and...

GENERAL INFORMATION
03-4
Checklist
Always adhere to the following.
Disposal:
lNever pour anything down a drain without first 
checking  that it is environmentally safe to do so, 
and that it does not contravene any local 
regulations or bye-laws;
l Have oil traps emptied regularly.
Spillage prevention:
lStore liquids in a walled area;
lMake sure that taps on liquid containers are 
secure and cannot be accidentally turned on;
lProtect bulk storage tanks from vandalism by 
locking the valves;
lTransfer...

GENERAL INFORMATION
03-5
Checklist
Always adhere to the following.
lIdentify where the neighbours who are likely to 
be affected are situated;
lMinimise noise, smells and traffic nuisance;
lPrevent litter by putting waste in the correct  
containers;
lHave waste skips emptied regularly.
Use of resource 
Another environmental concern is the waste of 
materials and energy that can occur in day to  day 
activities.
Electricity for heating, lighting and compressed air 
uses resources and releases pollution...

GENERAL INFORMATION
03-6
Dispose of waste in accordance with the following 
guidelines.
lFuel, hydraulic fluid, anti-freeze and oil: keep 
separate and dispose of to specialist  contractor. 
lRefrigerant: collect in specialist equipment and 
reuse.
lDetergents: safe to pour down the foul drain if 
diluted.
lPaint, thinners: keep separate and dispose of 
to specialist contractor.
lComponents: send back to supplier for 
refurbishment, or disassemble and reuse any 
suitable parts. Dispose of the remainder...

GENERAL INFORMATION
03-7
General inspection
All components should be inspected for wear or 
damage before being reassembled.
lNever inspect a component for wear or 
dimensional check unless it is absolutely clean; 
a slight smear of grease can conceal an 
incipient failure.
lWhen a component is to be checked 
dimensionally against recommended values, 
use the appropriate measuring equipment 
(surface plates, micrometers, dial gauges etc.). 
Ensure the measuring equipment is calibrated 
and in good...

GENERAL INFORMATION
03-8
lWhen fitting a bearing to a shaft, only apply 
force to the inner ring of the bearing. When 
fitting a bearing into a housing, only apply force 
to the outer ring of the bearing.
lIn the case of grease lubricated bearings (e.g. 
hub bearings) fill the space between bearing 
and outer seal with the recommended grade of 
grease before fitting seal.
lAlways mark components of separable bearings 
(e.g. taper roller bearings) when dismantling, to 
ensure correct reassembly. Never fit...

GENERAL INFORMATION
03-9
lUse the recommended service tool to fit an oil 
seal. If the correct service tool is not available, 
use a suitable tube approximately 0.4 mm 
(0.015 in.) smaller than the outside diameter of 
the seal. Use a hammer VERY GENTLY  on 
drift, if a suitable press is not  available.
lPress or drift the seal in to the depth of its 
housing with the sealing lip facing the lubricant 
to be retained if the housing is shouldered, or 
flush with the face of the housing where no 
shoulder...