Land Rover Discovery Series Ii 2002my Owners Handbook Nas Rover

							Bulb Replacement
210
HEADLIGHT AND SIDELIGHT
Light unit removal
First remove the access panel set into the 
bonnet locking platform above each headlight.To replace either the headlight or sidelight bulb, 
remove the light unit as follows:
Disengage the retaining clips ‘A’ and rotate 
them approximately 10 degrees (see inset) until 
they align with the slots in the headlight 
mounting panel. The light unit can now be 
released forward.
NOTE: DO NOT screw or unscrew the retaining 
clips more than described - their position 
affects the alignment of the headlights.
H2657
A
A
H3101 
						

							Bulb Replacement
211
Headlight bulb replacement
Disconnect the electrical multi-plug and 
remove the rubber cover. Release the spring 
clip which holds the bulb and withdraw the 
bulb from the light unit. When replacing the 
bulb, ensure that the larger tab is pointing 
towards the top of the headlight.
Replace the spring clip and rubber cover, 
ensuring the slit in the cover is at the top of the 
headlight, and pressing the centre firmly to seal 
around the electrical contacts of the bulb.
NOTE: Do not touch the bulb glass with your 
fingers. If necessary, clean the bulb with 
isopropyl rubbing alcohol. 
Replacing the headlight unit
Replacement is a reversal of the removal 
procedure.Sidelight bulb replacement
With the light unit removed (see previous 
instructions), disconnect the electrical 
multi-plug and disengage the bulb holder by 
twisting a quarter turn anti-clockwise. Pull the 
bulb from the holder to remove.
H3100 
						

							Bulb Replacement
212
FRONT DIRECTION INDICATOR AND SIDE 
MARKER LIGHT
Remove the retaining screw ‘A’, then ease the 
light unit forward to release it from the vehicle.
Both the small side marker light and larger 
direction indicator bulb holders are released 
from the light unit by twisting anti-clockwise.
Pull the side marker bulb to remove. Push and 
twist the direction indicator bulb to remove.
To replace the light unit, insert the two location 
pins (arrowed) on the outer side of the light unit 
into the vehicle body, push firmly into position 
and, finally, replace the retaining screw.
SIDE REPEATER LIGHT
Push the lens firmly to the left and withdraw the 
light unit from the wing. Twist to release the 
bulb holder from the lens unit, then pull the 
bulb from its socket.
When refitting, ensure that the little tabs 
(arrowed in illustration) are pointed to the right 
and are inserted into the aperture before 
pushing the light unit into position in the wing.
H2504
A
H2520 
						

							Bulb Replacement
213
REAR LIGHT CLUSTER 
(Tail, stop & reverse lights) 
From outside the vehicle remove the four 
retaining screws to release the light unit from 
the vehicle, then detach the electrical multi-plug
connector, by pressing the metal retaining 
spring.
To gain access to the bulbs, remove the five 
screws from the rear of the light unit and detach 
the bulb holder. Push and twist to release each 
bulb.
H2506 
						

							Bulb Replacement
214
BUMPER MOUNTED LIGHTS
(Fog guard lights & direction indicators)
WARNING
If the engine is warm, the exhaust system 
may be hot - to prevent personal injury, avoid 
contact with a hot exhaust system when 
reaching behind the bumper.
Reach behind the bumper and press the spring 
clip ‘A’ to release the light unit.
Squeeze both levers ‘B’ to release the bulb 
holder from the lens. Push and twist to release 
the bulbs.
NOTE: If necessary, the light unit can first be 
detached from the electrical harness by 
releasing the multi-plug from the rear of the 
bulb holder.
Before reassembling the light unit, make sure 
the seal (between holder and lens) is in place.To replace the light unit, first locate the hooks 
‘C’ in the bumper aperture and firmly push the 
other side of the light against spring pressure 
until it clicks into place.
NUMBER PLATE LIGHTS
Remove both screws to release the light unit. 
Ease the light unit from its recess and pull the 
bulb to remove. 
H2522
C
B
A
H2499 
						

							Bulb Replacement
215
FRONT FOG LIGHTS
The front fog lights are mounted on the rear of 
the front bumpers and are shielded from behind 
by the lower wheelarch liners.
Access is severely restricted and will entail lying 
beneath the centre of the vehicle at the front and 
reaching between the wheelarch liner and the 
back of the fog light.
To access the bulb, remove the cover on the 
rear of the fog light by twisting it anti-clockwise.Spring clips (similar to those in the headlights) 
hold the bulb in place. Unhook the clips to 
release the bulb from the light unit, then pull the 
bulb from the connector. Because access and 
vision are severely restricted (these operations 
must be carried out largely by ‘feel’), it may be 
helpful to first examine the way in which similar 
spring clips in the headlight unit retain the 
headlight bulb.
Before fitting the replacement bulb, note the 
‘flat’ on the otherwise circular shape of the bulb 
mounting flange. The flat acts as a key to enable 
correct positioning of the bulb in the light unit.
NOTE: Do not touch the bulb glass with your 
fingers. If necessary, clean the bulb with 
isopropyl rubbing alcohol.
H3552 
						

							Bulb Replacement
216
HIGH MOUNTED STOP LIGHT
Remove both retaining screws and the cover 
from the rear of the light unit. Twist the bulb 
holder anti-clockwise to remove. Push and 
twist anti-clockwise to release the bulb.
GLOVEBOX LIGHT
Insert a small flat-bladed screwdriver 
(preferably with a short handle, due to limited 
access) into the indent (arrowed in illustration) 
on the left hand side of the light unit, and 
carefully prise the unit from the glovebox panel. 
Remove the bulb from its clips.H2501
H2611 
						

							Bulb Replacement
217
INTERIOR COURTESY LIGHTS
Insert a small flat-bladed screwdriver into the 
indent on the side of the lens and carefully prise 
the lens from the light unit, then pull the bulb to 
remove. 
When replacing the lens, first locate the lug 
(arrowed in illustration), then push the lens into 
position.
INTERIOR LIGHT
Insert a small flat-bladed screwdriver into the 
indent on the side of the lens (where arrowed) 
and prise the lens from the light unit, then pull 
the bulb out from the clips.
H2462H2463 
						

							218 
						

							219
Technical Data
Technical Data
LUBRICANTS AND FLUIDS  . . . . . . . . . . . . . . . .  221
CAPACITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . .  223
ENGINES  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  224
ELECTRICAL SYSTEM . . . . . . . . . . . . . . . . . . . .  224
STEERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  224
DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . .  225
VEHICLE WEIGHTS  . . . . . . . . . . . . . . . . . . . . . .  226
TOWING WEIGHTS  . . . . . . . . . . . . . . . . . . . . . .  226
WHEELS & TYRES . . . . . . . . . . . . . . . . . . . . . . .  227