Land Rover Defender 90 Workshop 2nd Edition Nas Rover Manual
Have a look at the manual Land Rover Defender 90 Workshop 2nd Edition Nas Rover Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 364 Land Rover manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 400
ELECTRICAL
15
REPAIR STARTER MOTOR
Service repair no - 86.60.01
1.Position vehicle on ramp [hoist].
2.Disconnect battery negative lead.
3.Remove RH front heated oxygen sensor.
See
FUEL SYSTEM, Repair, heated oxygen
sensor (H02s)
4.Remove front bolt and loosen rear bolt securing
catalyst heat shield. Lower front edge of heat
shield.
5.Remove bolt securing starter motor heat shield
to RH engine mounting bracket.
6.Release heat shield clip from starter motor
solenoid and move aside for access.
7.Lower ramp...](http://img.usermanuals.tech/thumb/2848/48384/w64_defender-90-workshop-manual-2nd-edition-nas-rover-399.png "Page 400
ELECTRICAL
15
REPAIR STARTER MOTOR
Service repair no - 86.60.01
1.Position vehicle on ramp [hoist].
2.Disconnect battery negative lead.
3.Remove RH front heated oxygen sensor.
See
FUEL SYSTEM, Repair, heated oxygen
sensor (H02s)
4.Remove front bolt and loosen rear bolt securing
catalyst heat shield. Lower front edge of heat
shield.
5.Remove bolt securing starter motor heat shield
to RH engine mounting bracket.
6.Release heat shield clip from starter motor
solenoid and move aside for access.
7.Lower ramp...")
86ELECTRICAL 16 REPAIR IMMOBILIZATION (ALARM) ECU Service repair no - 86.77.01 Remove 1.Disconnect battery negative lead. 2.Remove steering wheel. If necessary, use puller LRT-57-014. 3.Remove instrument panel. See INSTRUMENTS, Repair, Instrument panel 4.Remove 2 screws securing immobilization ECU to fascia cowl. 5.Release ECU and disconnect both multi-plugs. 6.Remove ECU. NOTE: A new ECU must be initialised using TestBook.Refit 7.Reconnect multi-plugs and secure ECU to fascia cowl. 8.Fit instrument panel. See INSTRUMENTS, Repair, Instrument panel 9.Fit steering wheel. 10.Reconnect battery negative lead.
INSTRUMENTS 1 REPAIR INSTRUMENT PANEL Service repair no - 88.20.02 Remove 1.Disconnect battery negative lead. 2.Remove 4 screws securing instrument panel to fascia cowl. 3.Pull instrument panel away from fascia sufficent to reach behind speedometer. 4.Disconnect instrument harness multi-plug. 5.Disconnect 2 multi-plugs from warning light connectors. 6.Withdraw panel, complete with instruments. Refit 7.Offer up instrument panel and connect multi-plugs. 8.Secure instrument panel to fascia panel.SPEEDOMETER Service repair no - 88.30.01 Remove 1.Remove instrument panel assembly. See Instrument panel 2.Release tie sucuring harness and multiplug to speedometer. 3.Disconnect multi-plug from speedometer. 4.Unscrew retaining ring and remove speedometer. 5.Remove O ring from speedometer. Refit 6.Fit O ring to speedometer and position speedometer into instrument panel. 7.Fit retaining ring, align dial and tighten. 8.Connect multiplug to speedometer. 9.Secure harness and multiplug with tie. 10.Secure instrument panel to fascia cowl. See Instrument panel
88INSTRUMENTS 2 REPAIR TACHOMETER Service repair no - 88.30.21 Remove 1.Remove instrument panel. See Instrument panel 2.Release illumination bulb holder and wiring connectors from tachometer. - = BLACK + = WHITE 2 = RED 3.Unscrew retaining ring and remove tachometer. 4.Remove O ring from tachometer.Refit 5.Fit O ring to tachometer and position tachometer into instrument panel. 6.Fit retaining ring, align tachometer and tighten. 7.Fit instrument panel. See Instrument panel FUEL AND TEMPERATURE GAUGES Service repair no - 88.25.26 - Fuel gauge Service repair no - 88.25.14 - Temperature gauge Remove 1.Remove instrument panel. See Instrument panel 2.Release illumination bulb holder and multiplug from gauge. 3.Unscrew retaining ring and remove gauge, see 88M0186 . 4.Remove O ring from gauge. Refit 5.Fit O ring to gauge and position gauge into instrument panel. 6.Fit retaining ring, align gauge and tighten. 7.Fit instrument panel. See Instrument panel
INSTRUMENTS 3 REPAIR CLOCK Service repair no - 88.15.07 Remove 1.Remove 2 screws and withdraw switch panel from centre dash panel. 2.Release illumination bulb holder and disconnect electrical leads from clock. 3.Press in spring retainers and remove clock from panel. Refit 4.Fit clock into dash panel. 5.Fit electrical leadsbulb and bulb holder. 6.Secure switch panel to centre dash panel.WARNING LIGHT PANEL Service repair no - 88.20.18 Remove 1.Remove 2 screws and withdraw warning light panel. 2.Disconect both multi-plugs. 3.Disconnect illumination bulb leads. 4.Remove warning light panel. Refit 5.Fit illumination bulb leads and multi-plugs to warning light panel. 6.Secure warning light panel to instrument panel.
88INSTRUMENTS 4 REPAIR PRINTED CIRCUIT - WARNING LIGHT PANEL Service repair no - 88.20.20 Remove 1.Remove warning light panel. See Warning light panel 2.Remove 13 illumination bulb holders from light panel. 3.Release printed circuit from locating pins and remove from panel seatings. Refit 4.Fit new printed circuit over panel seatings and position on locating pins. 5.Fit illumination bulbs to secure circuit. 6.Fit warning light panel. See Warning light panel