Land Rover Defender 1999 2002my Workshop Supplement Body Repair 3rd Edition Rover Manual

12ENGINE
12
OVERHAUL Lash adjusters and finger followers - Inspection
1.Check lash adjuster bores for scoring and signs
of wear or damage.
2.Check lash adjusters for signs of wear, scoring
and overheating, replace as necessary. Ensure
oil hole in each lash adjuster is clear.
CAUTION: Store lash adjusters upright
and in their fitted order.
3.Check finger followers for wear and that rollers
are free to rotate.
CAUTION: Store finger followers in their
fitted order.
Camshaft - Inspection
1.Check camshaft...

ENGINE
13
OVERHAUL Camshaft bearings - check clearance
1.Position camshaft in cylinder head.
2.Place a piece of Plastigage along the centre line
of each camshaft bearing journal.
3.Carefully fit the camshaft carrier ensuring it is
located on dowels.
CAUTION: Do not rotate camshaft.
4.Fit original camshaft carrier retaining bolts and
tighten in sequence shown to25 Nm (18 lbf.ft).
5.Using sequence shown, loosen then remove
camshaft carrier retaining bolts.
CAUTION: Do not discard bolts at this
stage....

12ENGINE
14
OVERHAUL Valve springs - Inspection
1.Check free length of valve springs:
Free length =47.0±0.25 mm (1.85±0.011 in)
CAUTION: Valve springs must be replaced
as a set, if springs are to be refitted, keep
them in their fitted order.
Valves and valve guides - Inspection
1.Clean carbon from valves, check valves for
burning, pitting or cracking; replace as
necessary.
2.Clean carbon from valve seat inserts, remove all
loose particles on completion.
3.Check valve seat inserts for pitting and...

ENGINE
15
OVERHAUL Valves - Lapping-in
1.Lap each valve to its seat using grinding paste.
2.Apply Prussian Blue to valve seat, insert valve
into guide and press it firmly, without rotating on
to seat.
3.Remove valve and check that a continuous,
even line of Prussian Blue has been transferred
on to valve face.
NOTE: Line does not have to be across
whole width of valve face.
4.Remove all traces of grinding paste on
completion.
5.Check valve head stand-down.See this
Section.
Valve head stand down
1.Insert...

12ENGINE
16
OVERHAUL 5.Repeat above procedures for remaining rocker
arms.
CAUTION: Keep rocker arms in their fitted
order.Rocker arms and shaft - Inspection
1.Clean rocker arms and shaft, ensure oilways are
clear.
CAUTION: Identify type of rocker shaft
fitted. Engine Serial No. Prefixes 10P to
14P - Type A rocker shaft. Engine Serial
No. Prefixes 15P to 19P - Type B rocker shaft.
Type B rocker arms and shaft may be fitted to
Engine Serial No. Prefixes 10P to 14P as an
assembly.
2.Check diameter of each...

ENGINE
17
OVERHAUL
3.Using a vernier, check internal diameter of each
rocker arm, take 2 measurements at 180°.
Rocker arm internal diameter =27.0 to 27.013
mm (1.102 to 1.103 in)
CAUTION: Any ovality must be within
limits given.Rocker shaft - Assembling
1.Fit new spring ring to groove in rocker shaft.
2.Lubricate rocker shaft journals and rocker arms
with engine oil.
3.Fit rocker arm to shaft ensuring that it is in its
original fitted order.
4.Fit new spring ring to retain rocker arm.
5.Repeat above...

12ENGINE
18
OVERHAUL
4.Assemble valves, springs and valve spring caps
ensuring that they are in their original fitted
order.
5.Compress valve springs using toolLRT-12-034,
fit collets.
6.Using a wooden dowel and mallet, tap each
spring cap lightly to seat collets.
7.Lubricate new injector’O’rings with engine oil.
8.Using toolLRT-12-154/2, fit’O’ring to each
injector.
9.Using toolLRT-12-154/3, fit new sealing washer
to each injector.
10.Support each end of cylinder head on blocks of
wood.
CAUTION: Ensure...

ENGINE
19
OVERHAUL 16.Lubricate finger followers with engine oil.
17.Fit finger followers ensuring they are in their
original fitted order.
18.Lubricate cams and bearing journals on
camshaft, cylinder head and camshaft carrier
with engine oil.
19.Position camshaft in cylinder head with the
timing pin hole in the vertical position.
20.Apply an even film of sealant, Part No. STC
4600 to camshaft carrier face and spread to an
even film using a roller.
CAUTION: Ensure sealant does not block
oilways (arrowed)...

12ENGINE
20
OVERHAUL GASKET - ENGINE SUMP
Service repair no - 12.60.38.01
Remove
1.Remove 2 bolts securing centrifuge oil drain pipe
to sump, remove and discard gasket.
2.Using sequence shown and noting their fitted
positions, remove 20 bolts securing sump to
cylinder block.
3.Remove sump, remove and discard gasket.
CAUTION: Do not lever between sump and
cylinder block.Refit
1.Clean sump and mating faces, ensure bolt holes
in cylinder block are clean and dry.
2.Using suitable solvent, remove all traces...

ENGINE
21
OVERHAUL
7.Using sequence shown, tighten sump bolts to25
Nm (18 lbf.ft).
8.Fit new centrifuge oil drain pipe gasket.
CAUTION: Gasket must be fitted dry.
9.Fit centrifuge oil drain pipe, fit bolts and tighten
to10 Nm (7 lbf.ft).SEAL - CRANKSHAFT - REAR
Service repair no - 12.21.20.01
Remove
1.Remove flywheel.See Repair.
2.Remove sump gasket.See this Section.
3.Remove 5 bolts securing crankshaft rear oil seal
housing to cylinder block.
4.Remove and discard crankshaft rear oil seal and
housing....