Land Rover Defender 1999 2002my Workshop Supplement Body Repair 3rd Edition Rover Manual

12ENGINE
2
OVERHAUL GASKET - EXHAUST MANIFOLD
Service repair no - 30.15.12.01
Remove
NOTE: The following procedure covers
both EU3 and non EU3 engines
NOTE: EU3 engine illustrated.
1.Remove 3 bolts securing heater pipe to cylinder
head and turbocharger heat shield.
2.Remove heater pipe.
3.Remove bolt and remove turbocharger heat
shield.
4.Remove and discard 2 Allen screws securing
EGR pipe to exhaust manifold.
5.Remove banjo bolt securing oil feed pipe to
turbocharger and discard sealing washers....

ENGINE
3
OVERHAUL GASKET - CYLINDER HEAD
Service repair no - 12.29.02.01
Remove
CAUTION: The following procedures
should only be carried out when cylinder
head is to be overhauled; for replacement
of cylinder head gasket only, see Repairs section -
Gasket - Cylinder head.
NOTE: The following procedure covers
both EU3 and non EU3 engines
1.Remove exhaust manifold gasket.See
MANIFOLD AND EXHAUST SYSTEM, Repair.
2.Remove inlet manifold gasket.See MANIFOLD
AND EXHAUST SYSTEM, Repair.
3. Models with EGR...

12ENGINE
4
OVERHAUL
11.Disconnect alternator/vacuum pump oil feed pipe
union from cylinder head, remove and discard
’O’ring.
12.Remove camshaft sprocket access plug from
front of cylinder head, remove and discard’O’
ring.
13.Remove timing chain fixed guide Allen screw.
14.Remove timing chain tensioner, remove and
discard sealing washer.
15.Remove and discard 3 bolts securing camshaft
sprocket to camshaft; release sprocket from
camshaft.
16.Remove bolt and nut securing front of cylinder
head to timing...

ENGINE
5
OVERHAUL Refit
1.Thoroughly clean cylinder block and cylinder
head mating faces.
2.Ensure coolant and oil passageways are clear
and bolt holes are clean and dry.
3.Ensure locating dowel holes in cylinder block are
clean and dry.
4.Fit new plastic locating dowels in cylinder block.
5.Fit new cylinder head gasket of the correct
thickness with the word’TOP’uppermost.
CAUTION: Gasket must be fitted dry.
6.Ensure that camshaft timing pinLRT-12-158is
still in position and using assistance, fit...

12ENGINE
6
OVERHAUL 14.Clean fixed guide Allen screw and apply Loctite
242 to screw threads.
15.Fit fixed timing chain guide Allen screw and
tighten to25 Nm (18 lbf.ft).
16.Clean timing chain tensioner and fit new sealing
washer.
17.Fit timing chain tensioner and tighten to45 Nm
(33 lbf.ft).
18.Tighten camshaft sprocket bolts to36 Nm (27
lbf.ft).
19.Remove toolLRT-12-058from camshaft.
20.Lubricate a new’O’ring with engine oil and fit to
camshaft sprocket access plug.
21.Fit camshaft sprocket access...

ENGINE
7
OVERHAUL CYLINDER HEAD GASKET SELECTION
NOTE: There are three thicknesses of
cylinder head gasket available and in order
that the correct gasket is fitted, it will be
necessary to determine the stand proud
(protrusion) of each piston above the top face of
the cylinder block. Gaskets have either 1, 2 or 3
identification holes and the following procedures
must be followed in order that the correct gasket
is selected.
1.Temporarily fit and lightly tighten a new
crankshaft pulley bolt.
2.Assemble a...

12ENGINE
8
OVERHAUL CYLINDER HEAD - OVERHAUL
Service repair no - 12.29.19.01
Dismantling
1.Remove cylinder head gasket.See this
Section.
CAUTION: Due to the design of the
cylinder head which incorporates drillings
for the fuel injection system, it is important
that absolute cleanliness is adhered to when
carrying out overhaul procedures.
2.Note the gasket thickness indicator and ensure
the same thickness gasket is used on refitment
of cylinder head.
CAUTION: If new pistons, connecting rods
or crankshaft...

ENGINE
9
OVERHAUL
8.Gently tap camshaft carrier upwards to break
sealant bond, remove carrier.
NOTE: Dowel located.
9.Remove camshaft.
10.Remove and discard camshaft rear oil seal.
11.Remove finger followers and lash adjusters.
CAUTION: Store lash adjusters and finger
followers in their fitted order and store
lash adjusters upright. Maintain absolute
cleanliness when handling components.
12.Remove and discard 5 bolts securing EUI
retainers.
13.Using toolLRT-12-154/1remove EUI units from
cylinder head and...

12ENGINE
10
OVERHAUL
20.Using toolLRT-12-071, remove and discard
valve stem oil seal.
21.Repeat above operations to remove remaining
valves.
22. Engine Serial No. Prefixes 15P to 19P:-
Disconnect spill return pipe from cylinder head
and fuel connector block, remove and discard’O’
rings. 

ENGINE
11
OVERHAUL
23.Remove 3 bolts and remove fuel connector
block from cylinder head.
24.Remove and discard gasket,’O’ring and fuel
filter.
25.Remove spacer block and gasket (if fitted).Cylinder head and camshaft carrier - cleaning
1.Thoroughly clean cylinder head mating faces,
ensure oil and coolant passages are clear and
bolt holes are clean and dry.
CAUTION: Take care to ensure that EUI
drillings are clear.
2.Using suitable solvent, remove all traces of
sealant and gasket material.
CAUTION: Do not...