Land Rover Defender 1999 2002my Workshop Supplement Body Repair 3rd Edition Rover Manual

							Workshop Manual
Werkplaatshandboek
Manual dAtelier
Werkstatthandbuc h
Manuale dOfficina
Manual de Taller
Manual de Oficina 
						

							DEFENDER 1999 & 2002 MY
WORKSHOP MANUAL SUPPLEMENT& BODY REPAIR MANUAL
This Supplement supersedes Workshop Manual VDR 100250
and should be used in conjunction with the following Manuals:
Workshop Manual - Defender 300 Tdi LRL 0097
Overhaul Manual - R380 gearbox LRL 0003 3rd edition
Overhaul Manual - LT230T Transfer gearbox LRL 0081 3rd edition
Publication  Part  No.  LRL  0410ENG  (3rd  Edition)
 Land Rover 2001
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form, electronic,
mechanical, recording or other means without prior permission from Land Rover. 
						

							CONTENTS
01 INTRODUCTION
04 GENERAL SPECIFICATION DATA
05 ENGINE TUNING DATA
07 GENERAL FITTING REMINDERS
09 LUBRICANTS, FLUIDS AND CAPACITIES
10 MAINTENANCE
12 ENGINE
17 EMISSION CONTROL
18 ENGINE MANAGEMENT SYSTEM
19 FUEL SYSTEM
26 COOLING SYSTEM
30 MANIFOLD AND EXHAUST SYSTEM
33 CLUTCH
37 MANUAL GEARBOX
41 TRANSFER GEARBOX
47 PROPELLER SHAFTS
57 STEERING
60 FRONT SUSPENSION
64 REAR SUSPENSION
70 BRAKES
76 CHASSIS AND BODY
77 PANEL REPAIRS
82 AIR CONDITIONING
84 WIPERS AND WASHERS
86 ELECTRICAL
88 INSTRUMENTS
01
04
05
07
09
10
12
17
18
19
26
30
33
37
41
47
57
60
64
70
76
77
82
84
86
88 
						

							01 - INTRODUCTION
CONTENTS
Page
INFORMATION
INTRODUCTION 1..................................................................................................
DIMENSIONS 1.......................................................................................................
REFERENCES 1.....................................................................................................
REPAIRS AND REPLACEMENTS 1.......................................................................
POISONOUS SUBSTANCES 1..............................................................................
FUEL HANDLING PRECAUTIONS 2......................................................................
SYNTHETIC RUBBER 3.........................................................................................
RECOMMENDED SEALANTS 3.............................................................................
USED ENGINE OIL 3..............................................................................................
ACCESSORIES AND CONVERSIONS 4...............................................................
WHEELS AND TYRES 4.........................................................................................
STEAM CLEANING 4..............................................................................................
SPECIFICATION 4..................................................................................................
SPECIAL SERVICE TOOLS 4................................................................................
JACKING 5..............................................................................................................
HYDRAULIC VEHICLE RAMP (FOUR POST) 6.....................................................
TWO POST VEHICLE RAMPS 6............................................................................
DYNAMOMETER TESTING 6................................................................................
TOWING 7..............................................................................................................
TRANSPORTING THE VEHICLE BY TRAILER 7..................................................
JUMP STARTING 8................................................................................................
ABBREVIATIONS AND SYMBOLS USED IN THIS MANUAL 9.............................
CROSS REFERENCE OF EMISSION SYSTEM TERMINOLOGY 10....................
VEHICLE IDENTIFICATION NUMBER (VIN) 11.....................................................
LOCATION OF IDENTIFICATION NUMBERS 12...................................................
FAULT DIAGNOSTIC EQUIPMENT 13..................................................................
READING THIS SUPPLEMENT 14........................................................................ 
						

							INTRODUCTION
1
INFORMATION INTRODUCTION
This Workshop Manual Supplement covers vehicles
from 1999 and 2002 model year onwards. The Body
Repair Manual has also been incorporated into this
supplement. Amendments and additional pages will
be issued, when necessary, to ensure that the
supplement covers latest models.
This Supplement is designed to assist skilled
technicians in the efficient repair and maintenance of
Land Rover Defender vehicles.
Individuals who undertake their own repairs should
have some skill and training, and limit repairs to
components which could not affect the safety of the
vehicle or its passengers. Any repairs required to
safety critical items such as steering, brakes,
suspension or supplementary restraint system should
be carried out by a Land Rover Dealer. Repairs to
such items should NEVER be attempted by untrained
individuals.
WARNINGS, CAUTIONSandNOTESare given
throughout this Manual in the following form:
WARNING: Procedures which must be
followed precisely to avoid the possibility
of personal injury.
CAUTION: This calls attention to
procedures which must be followed to
avoid damage to components.
NOTE: This calls attention to methods
which make a job easier or gives helpful
information.
DIMENSIONS
The dimensions quoted are to design engineering
specification. Alternative unit equivalents, shown in
brackets following the dimensions, have been
converted from the original specification.REFERENCES
References to the left or right hand side in the manual
are made when viewing the vehicle from the rear.
With the engine and gearbox assembly removed, the
crankshaft end of the engine is referred to as the front.
To reduce repetition, some operations covered in this
Supplement do not include reference to testing the
vehicle after repair.
It is essential that work is inspected and tested after
completion and if necessary a road test of the vehicle
is carried out, particularly where safety related items
are concerned.
REPAIRS AND REPLACEMENTS
When replacement parts are required it is essential
that Land Rover parts are used.
Attention is particularly drawn to the following points
concerning repairs and the fitting of replacement parts
and accessories: Safety features embodied in the
vehicle may be impaired if other than Land Rover
parts are fitted. In certain territories, legislation
prohibits the fitting of parts not to the vehicle
manufacturer’s specification. Torque spanner values
given in the Supplement must be strictly adhered to.
Locking devices, where specified, must be fitted. If the
efficiency of a locking device is impaired during
removal it must be replaced with a new one. Certain
fasteners must not be re-used. These fasteners are
specified in the Supplement.
POISONOUS SUBSTANCES
Many liquids and other substances used are
poisonous and therefore must not be consumed. It is
also advisable to keep all substances away from open
wounds. These substances among others include
anti-freeze, brake fluid, fuel, windscreen washer
additives, air conditioning refrigerant, lubricants and
various adhesives. 
						

							01INTRODUCTION
2
INFORMATION FUEL HANDLING PRECAUTIONS
The following information provides basic precautions
which must be observed if fuel is to be handled safely.
It also outlines the other areas of risk which must not
be ignored.
This information is issued for basic guidance only, and
in any case of doubt, appropriate enquiries should be
made of your local Fire Officer or Fire Department.
Fuel vapour is highly flammable and in confined
spaces is also very explosive and toxic and when
diluted with air becomes a readily ignitable mixture.
The vapour is heavier than air and will always fall to
the lowest level. It can readily be distributed
throughout a workshop by air current, consequently,
even a small spillage of fuel is very dangerous.
Always have a fire extinguisher containingFOAM CO
2
GAS,orPOWDERclose at hand when handling fuel,
or when dismantling fuel systems and in areas where
fuel containers are stored.
WARNING: lt is imperative that the battery
is not disconnected during fuel system
repairs as arcing at the battery terminal
could ignite fuel vapour in the atmosphere.
Always disconnect the vehicle battery BEFORE
carrying out work on the fuel system.
Whenever fuel is being handled, transferred or
stored, or when fuel systems are being dismantled
all forms of ignition must be extinguished or
removed, any leadlamps used must be flame proof
and kept clear of spillage.
No one should be permitted to repair components
associated with fuel without first having had fuel
system training.Hot fuel handling precautions
WARNING: Before commencing any
operation requiring fuel to be drained from
the fuel tank, the following procedure must
be adhered to:
1.Allow sufficient time for the fuel to cool, thus
avoiding contact with hot fuels.
2.Vent the system by removing the fuel filler cap in
a well ventilated area. Refit the filler cap until the
commencement of fuel drainage.
Fuel transfer
WARNING: Fuel must not be extracted or
drained from any vehicle while it is
standing over a pit.
The transfer of fuel from the vehicle fuel tank must be
carried out in a well ventilated area. An approved
transfer tank must be used according to the transfer
tank manufacturer’s instructions and local regulations,
including attention to grounding of tanks.
Fuel tank removal
AFUEL VAPOURwarning label must be attached to
the fuel tank upon removal from the vehicle.
Fuel tank repair
Under no circumstances should a repair to any tank
be attempted. 
						

							INTRODUCTION
3
INFORMATION SYNTHETIC RUBBER
Many’0’ring seals, flexible pipes and other similar
items which appear to be natural rubber are made of
synthetic materials called Fluoroelastomers. Under
normal operating conditions this material is safe, and
does not present a health hazard. However, if the
material is damaged by fire or excessive heat, it can
break down and produce highly corrosive Hydrofluoric
acid which can cause serious burns on contact with
skin. Should the material be in a burnt or overheated
condition handle only with seamless industrial gloves.
Decontaminate and dispose of the gloves immediately
after use.
If skin contact does occur, remove any contaminated
clothing immediately and obtain medical assistance
without delay. In the meantime, wash the affected
area with copious amounts of cold water or limewater
for fifteen to sixty minutes.
RECOMMENDED SEALANTS
A number of branded products are recommended in
this manual for use during maintenance and repair
work.
These items include:
HYLOMAR GASKET AND JOINTING COMPOUND
and
HYLOSIL RTV SILICONE COMPOUND.
They should be available locally from garage
equipment suppliers. If there is any problem obtaining
supplies, contact the following company for advice
and the address of the nearest supplier.
MARSTON LUBRICANTS LTD.
Hylo House,
Cale Lane,
New Springs,
Wigan WN2 1JR
Tel 01942 824242USED ENGINE OIL
WARNING: Prolonged and repeated
contact with engine or motor oil will result
in the removal of natural fats from the
skin, leading to dryness, irritation and dermatitis.
Used engine oil contains potentially harmful
contaminants which may cause skin cancer.
Adequate means of skin protection and washing
facilities should be provided.
Handling precautions
1.Avoid prolonged and repeated contact with oils,
particularly used engine oils.
2.Wear protective clothing, including impervious
gloves where applicable.
3.Do not put oily rags in pockets.
4.Avoid contaminating clothes, particularly
underwear, with oil.
5.Overalls must be cleaned regularly. Discard
unwashable clothing and oil impregnated
footwear.
6.First aid treatment must be obtained immediately
for open cuts and wounds.
7.Use barrier creams, before each work period, to
help the removal of oil from the skin.
8.Wash with soap and water to ensure all oil is
removed (skin cleansers and nail brushes will
help). Preparations containing lanolin replace the
natural skin oils which have been removed.
9.Do not use gasoline, kerosene, diesel fuel,
petrol, thinners or solvents for washing the skin.
10.If skin disorders develop, obtain medical advice.
11.Where practicable, degrease components prior
to handling.
12.Where there is a risk of eye contact, eye
protection should be worn, for example, goggles
or face shields; in addition an eye wash facility
should be provided.
Disposing of used oils
Environmental protection precaution
It is illegal to pour used oil onto the ground, down
sewers or drains, or into waterways.
Dispose of used oil through authorised waste disposal
contractors. If in doubt contact your Local Authority for
advice on disposal facilities.