Land Rover Body And Paint Air Bag And Safety Belt Rover Manual

Heater Lines
Quick release connections to engine cooling
system
1
Quick release connections to main heater2
Auxiliary climate control assembly3
In-line connections4
Auxiliary Climate ControlLesson 2 – Electrical
29Technical Training (G421237) 

DISTRIBUTION SYSTEM
Second row left face level air duct1
Cross-car air duct2
Second row right face level air duct3
Right C pillar air duct4
Third row right face level register5
Second row face level registers6
Third row foot level air duct7
Third row foot level registers8
Third row left face level register9
Left C pillar air duct10
(G421237) Technical Training30
Lesson 2 – ElectricalAuxiliary Climate Control 

The distribution system consists of a network of air
ducts that supply air from the outlets of the auxiliary
climate control assembly to registers installed in:
•The headliner, to the left and right of the second row
interior lamp, to provide face level ventilation for
second row seat occupants
•The left and right C pillar finishers, to provide face
level ventilation for third row seat occupants
•The loadspace left side molding, to provide foot level
ventilation for third row passengers.
The registers...

ACCM Harness Connector C0695
ACCM Harness Connector C0695 Pin Details
Input/OutputDescriptionPin No.
InputPower supply from ATCM1
Input/OutputLIN bus2
OutputGround3
OutputRear blower module power drive4
InputBlower motor voltage sense5
InputCabin temperature sensor signal6
-Not used7and 8
OutputSensor ground9
OutputRear blower relay coil drive10
OutputSolenoid valve drive11
InputEvaporator temperature sensor signal12
(G421237) Technical Training32
Lesson 2 – ElectricalAuxiliary Climate Control 

COOL BOX
Cubby box lid1
Cubby box tray2
Container3
On/Off switch4
Thermoelectric cooler heatsink5
Fan6
Electrical connector7
The cool box is an open topped container with an
aluminum liner and an insulating outer layer. A
thermoelectric cooler is installed in the front of the
container. The top of the container is covered by the
cubby box tray and the cubby box lid. An electrical
connector on the front of the cool box connects the cool
box to the console harness.
Operation of the thermoelectric cooler is...

When the on/off switch is selected on, the LED in the
switch illuminates and power is supplied to the
thermoelectric cooler. The couples in the thermoelectric
cooler then transfer heat from the liner of the cool box
to the heatsink, and the fan runs to cool the heatsink.
(G421237) Technical Training34
Lesson 2 – ElectricalAuxiliary Climate Control 

AUXILIARY CLIMATE CONTROL DIAGRAM
NOTE: A = Hardwired connection; O = LIN bus
Auxiliary Climate ControlLesson 2 – Electrical
35Technical Training (G421237) 

Battery1
Fuse 22B, CJB2
Rear blower relay3
Rear blower4
Rear blower control module5
Solenoid valve6
ACCM7
Temperature blend door motor8
Distribution door motor9
ATCM10
Evaporator temperature sensor11
Thermoelectric cooler12
Cool box on/off switch13
Fuse 55P, CJB14
Fusible link 18E, Battery Junction Box (BJB)15
Fusible link 17E, BJB16
Fuse 51P, CJB17
(G421237) Technical Training36
Lesson 2 – ElectricalAuxiliary Climate Control 

Cellular Phone Component Location
Microphone1
Transceiver Module (TM)2
Cellular Phone Antenna3
Base plate adaptor4
Adaptor cradle5
Speaker6
Clock spring7
Steering wheel switches8
Amplifier9
IHU10
Speakers11
Cellular PhoneLesson 2 – Electrical
217Technical Training (G421305) 

Cellular Phone Control Diagram
NOTE: A= Hardwired P= MOST
Mobile handset1
Adaptor cradle2
Speakers3
Audio amplifier4
Base plate adaptor5
IHU6
Transceiver Module (TM)7
Cellular Phone Antenna8
Clock spring9
Steering wheel switches10
Microphone11
(G421305) Technical Training218
Lesson 2 – ElectricalCellular Phone