Land Rover Body And Paint Air Bag And Safety Belt Rover Manual

ABS module7
Transmission control module8
Transfer box ECU9
Electric park brake module10
HEVAC ECU11
Engine control module12
Left outer front sensor13
Left inner front sensor14
Right inner front sensor15
Right outer front sensor16
Left outer rear sensor17
Left inner rear sensor18
Right inner rear sensor19
Right outer rear sensor20
Parking aid switch21
Parking AidLesson 2 – Electrical
121Technical Training (G421252) 

Workshop safety
This page highlights the general observations expected
whilst attending this training programme, and its
continuation upon returning to your place of work.
General
Whilst working on all vehicles, the following items
where available should always be used:
•Wing covers
•Seat covers
•Floor protection
Optional items:
•Steering wheel cover
•Park brake lever cover
•Door grab handle protection
Safety
All precautions must be taken and observed at all times,
to prevent injury or damage to the...

COMPONENT LOCATIONS (FIVE SEAT VEHICLES)
(G421345) Technical Training250
Lesson 3 – Body and PaintSafety Belt System 

COMPONENT LOCATIONS (SEVEN SEAT VEHICLES)
GENERAL
A three point safety belt is installed at each seat position.
Except in North American Specification (NAS) markets,
all of the safety belts have Emergency Locking
Retractors (ELR). In NAS markets, only the driver seat
is fitted with an ELR; all of the passenger safety belts
have Automatic Locking Retractors (ALR).
Both types of retractor incorporate a liftshaft locking
system with webbing sensor and car sensor activating
mechanisms. The webbing sensor...

The ALR has a mode of operation where the retractor
will take up slack in the webbing, but not allow any
slack to be paid out. This mode of operation can be used
to secure a child seat.
•To engage the ALR child seat mode of operation:
Pull the webbing out of the retractor to its full extent.
•To cancel the ALR child seat mode of operation:
Allow the retractor to fully rewind the webbing.
A safety belt warning indicator is installed in the
instrument cluster to remind the front seat occupants to
fasten...

•The safety belt of each occupied front seat is
fastened.
•The ignition switch is turned to position 0.
•The vehicle speed decreases to 5 km/h (3 mph).
The belt minder function can be enabled and disabled
using the driver safety belt switch. The instrument
cluster changes the state of the belt minder function if,
within 60 seconds of first turning the ignition switch to
position II, the driver safety belt is fastened and
unfastened nine times. Successful completion of the
change is indicated by a single...

Component Location
NOTE: RH drive shown, LH drive similar
Drivers seat cushion adjustment motor assembly1
Drivers seat memory switch pack2
Drivers seat non-memory switch pack3
Drivers door ajar switch4
Drivers seat squab motor5
Drivers seat heating element6
Second row heated seat switch pack (vehicles
with rear air conditioning)
7
Second row RH seat heating element8
Second row RH seat heating module9
Second row LH seat heating element10
Second row heated seat switches (vehicles
without rear air...

Second row LH seat heating module12
Front passenger seat heating element13
Front passenger seat squab motor14
Front passenger seat cushion adjustment motor
assembly
15
Front passenger seat switch pack16
Central Junction Box (CJB)17
Front heated seat switch pack (climate control
system)
18
Memory control module19
Front passenger seat power relay20
GENERAL
Seat Configuration
L319 is available in a 5 or 7 seat configuration. The
drivers seat has the option of an 8-way power
adjustment, with or without...

MANUAL FRONT SEATS
Height adjustment (drivers seat only)1
Recline adjustment2
Forward/backward adjustment3
Lumber support adjustment4
Folding armrest adjustment (if fitted)5
(G421327) Technical Training236
Lesson 3 – Body and PaintSeats 

Height adjustment (drivers seat only)
Pumping the handle controls seat height. Pumping the
lever upwards raises the seat; downwards lowers the
seat.
Recline adjustment
The angle of the backrest is adjusted by turning the
rotary wheel either clockwise or anticlockwise.
Forward/backward adjustment
Lifting the tomel bar at the front of the seat and sliding
the seat to the desired position achieves the
forwards/backwards adjustment.
Lumber support adjustment
A hand wheel in the side of the seat provides for...