Land Rover Body And Paint Air Bag And Safety Belt Rover Manual

Seat cushion height adjustment3
Forward/Backward adjustment
Push and hold the switch forwards or backwards to move
the seat to the desired position.
Seat back adjustment
Twist the switch forwards or backwards until the desired
seat back angle is achieved.
Seat cushion height adjustment
Push the switch up or down to raise or lower the
cushion.
Front Seat Motors
The seat motors are a permanent magnet motor type
coupled to a rack and pinion assembly. Should the motor
seize or stick an internal thermal...

NOTE: This does not include lazy entry where the door
is not required to be open, or the ignition key is in
position I or II.
The mirror adjustment is only enabled when the ignition
key is in position I or II.
Memory Recall
Memory recall has three memory positions stored for
the seats and exterior mirrors. The switches for this
function are located on drivers seat outer side trim
panel. Pressing the appropriate numbered memory
switch allows the seat to start moving to the position
appropriate to that...

Control Module Pin
8
Control Module Pin
13
Control Module Pin
7
Control Module Pin
14
Action
-Ground--Passenger Mirror
Down
Ground---Passenger Mirror
Left
Battery---Passenger Mirror
Right
Lazy Entry
Pressing the unlock button on the remote transmitter
will initiate a memory recall. This feature is known as
lazy entry. If the seat movement, memory switch or
the lock button on the remote transmitter is pressed,
then the lazy entry feature will stop immediately.
The memory settings are stored within...

Slide
Backward
Slide
Forward
Height
Down
Height UpTilt DownTilt UpRecline
Down
Recline
Up
No*No*-NoYesYesYesYesHeight
Down
No-No*No*No*No*YesYesSlide
Forward
-NoNo*No*No*No*YesYesSlide
Backward
Key
•- = Not applicable
•Yes = Can be activated together
•No = Can not be activated together (Physically
impossible)
•No* = Can not be activated together (Relay sharing
restriction)
If two axis are being driven and a third axis is requested
to move, the third switch request is ignored until either
of the two axis...

Most recent ignition keyA
Second most recent ignition keyB
Third most recent ignition keyC
First reverse gear mirror position store1
Second reverse gear mirror position store2
Third reverse gear mirror position store3
The reverse gear mirror position feature can be activated
or deactivated via the customer personalisation feature
of the high line instrument cluster. This provides the
driver with the option to enable or disable reverse gear
mirror position as required. Information regarding the
reverse...

ConditionsAudible ConfirmationOperation
Successful store operation completedSingle ChimeMemory Store
Only issued if all axis of movement
successfully reach the intended posi-
tion
Double ChimeMemory Recall
Successful store operation for reverse
mirror position completed
Single ChimeReverse Gear Mirror Position Store
In addition to audible confirmation there is also a visual
confirmation via the instrument cluster message centre.
MEMORY CONTROL MODULE
Memory Control Module Location (LHD shown, RHD...

If a stall condition is detected then the drive to that axis
is cancelled for the remainder of that memory operation
(memory recall) or until the switch is re-selected
(manual movement).
If the motor movement has stopped due to loss of sensor
feedback, either stall or sensor failure, then that axis
may be activated again, to move past the stall position,
by re-selecting the appropriate switch. This allows
control of the motor to be maintained if sensor feedback
is lost.
Upon re-selection of movement, if...

SEAT HEATING
SeatsLesson 3 – Body and Paint
245Technical Training (G421327) 

Front Seats
Front Seat Heater Switches
The heated front seat system is available on both manual
and electric seats and is controlled by the Automatic
Temperature Control Module (ATCM).
When the front seat heater switch is operated, power is
supplied to the heater elements in the seat, causing the
seat to heat up. The ATCM senses seat temperature via
the sensor in the cushion and regulates voltage to the
seat heater elements to maintain a constant temperature.
Rear Seat Heaters
Rear Seat Heater Switches...

control module de-energises the heater elements and
extinguishes the second LED. The seat heaters remain
on until selected off or the ignition is turned off.
The rear seat heat control modules receive an input from
a temperature sensor in RH and LH rear seats, and
regulate the power feed of the heater elements to control
the seat temperature at the appropriate temperature
setting between 35 and 45 °C (95 and 113 °F). The
actual temperature settings vary with the type of seat
covering, to allow for the...