Land Rover Anti Lock Control Traction Control Rover Manual
Here you can view all the pages of manual Land Rover Anti Lock Control Traction Control Rover Manual. The Land Rover manuals for Automobile are available online for free. You can easily download all the documents as PDF.
Page 71
Battery1 Fusible link 11E, BJB2 Fusible link 8E, BJB3 Air suspension ECU4 Diagnostic socket5 Instrument cluster6 Integrated head unit7 Parking brake module8 Automatic Temperature Control Module (ATCM) 9 Tire Pressure Monitoring Module (TPMM)10 Park Distance Control Module (PDCM)11 Central Junction Box (CJB)12 Transfer box control module13 Engine Control Module (ECM)14 Rear differential control module15 ABS control module16 Transmission Control Module (TCM)17 Clutch pedal position sensor18 Restraints...
Page 72
GENERAL Electronic rear differentialA Open rear differentialB Rear driveshaft1 Electronic rear differential2 RH rear drive halfshaft3 Actuator (locking) motor assembly4 LH rear drive halfshaft5 Rear differential6 The open rear differential converts the angle of drive through 90° and distributes drive, via the rear drive halfshafts, to the rear wheels. (G421061) Technical Training88 Lesson 2 – ChassisRear Drive Axle and Differential
Page 73
The open rear differential for the V6 and V8 petrol variants has the same output ratio, but the output ratios for the TdV6 diesel are different, depending on whether automatic or manual transmission is fitted. The open rear differential is located centrally in the rear of the chassis. The units are mounted to the chassis via rubber bushes and bolts; two mounting points at the rear of the unit and one at the front. Rear Drive Axle and DifferentialLesson 2 – Chassis 89Technical Training (G421061)
Page 74
OPEN REAR DIFFERENTIAL ASSEMBLY Open Rear Differential - Exploded View (G421061) Technical Training90 Lesson 2 – ChassisRear Drive Axle and Differential
Page 75
Cap1 Seal2 Bearing assembly, without race3 Bearing pre-load spacer4 Bearing5 Roller bearing cup6 Cover7 Seal8 Differential carrier9 Gear and pinion assembly10 Bearing11 Roller bearing cup12 Shim13 Collapsible spacer14 Pinion nut15 Retainer16 Flange17 Outer deflector18 Inner deflector19 Oil seal20 Bearing21 Roller bearing cup22 Roll pin23 Breather cap24 Breather25 Case26 Data location27 Mounting bush28 Bearing29 Bearing pre-load spacer30 Roller bearing cup31 Plug32 Drain plug33 Thrust washer34 Planet...
Page 76
The differential comprises a pinion shaft and hypoid pinion gear and a crown wheel drive gear with an integral cage, which houses two planet gears. Two sun wheels are also located in the cage and pass the rotational drive to the drive shafts. The pinion shaft is mounted on two opposed taper roller bearings, with a collapsable spacer located between them. The spacer is used to hold the bearings in alignment and also collapses under the pressure applied to the pinion flanged nut. This allows the flanged...
Page 77
SERVICE The oil used in the open rear differential is Castrol SAF-XO. The oil contains unique additives, which enhance the differentials operation. No other oil must be used in the open rear differential. Open Rear Differential Serviceable Components •Needle roller bearing assemblies •Halfshaft seals •Chassis bush/fixings •Lubricant. Rear Drive Axle and DifferentialLesson 2 – Chassis 93Technical Training (G421061)
Page 78
ELECTRONIC REAR DIFFERENTIAL ASSEMBLY Electronic Rear Differential - Exploded View (G421061) Technical Training94 Lesson 2 – ChassisRear Drive Axle and Differential
Page 79
Cap1 O ring2 Bearing pre-load spacer3 Bearing4 Bearing cup5 Bolt, 4 of6 Housing and motor assembly7 Damper8 Gear and pinion assembly9 Bearing10 Bearing cup11 Shim12 Collapsible spacer13 Pinion nut14 Retainer15 Flange16 Deflector, outer17 Deflector, inner18 Seal19 Bearing20 Bearing cup21 Breather cap22 Breather23 Case24 Data location25 Mounting bush26 Bearing27 Bearing assembly without race28 Bearing cup29 Filler plug30 Drain plug31 Electronic differential assembly32 Bolt, 10 of33 O ring34 Cover35 Bolt,...
Page 80
Actuator1 Clutch pack2 Differential3 The electronic rear differential locking and biasing feature is actuated via a DC motor, which is controlled by the electronic rear differential control module, via a Pulse Width Modulation (PWM) signal. (G421061) Technical Training96 Lesson 2 – ChassisRear Drive Axle and Differential