Kyocera TASKalfa 181 User Manual

Optional Equipment
4-2
Notes on Use
Be sure not to use the following as originals in the document processor. In addition, originals with 
punched holes or perforations should be set so t hat the edge of the paper with the holes or 
perforations is facing away from the directi on of insertion into the document processor.
• Transparencies
• Carbon paper, crumpled originals or originals with  strong folds, and soft originals such as vinyl
• Originals which are not rectangular, wet originals, and originals...

Optional Equipment4-3
Notes• Before setting originals,  make sure that there are 
no originals remaining on the original eject table. 
Originals left on the eject table may cause other 
originals to jam.
• When setting multiple originals at one time, be  sure to use originals of the same size. It is, 
possible, however to use different size originals of 
the same width (for example, 11 × 17 (Ledger) 
and 11 × 8
1/2 or A4 and A3 at the same time in 
the auto selection mode. (Refer to  Chapter 1 in...

Optional Equipment
4-4
Setting Originals on the Platen
When copying from an original which cannot be set in 
the document processor, open the document processor 
and set the original directly on the platen.
Notes• Before opening the document processor, make sure that there are no originals remaining on the original table or on the original eject table. If there are originals left in either place, they may 
fall off the machine when the document processor is opened.
• When double-page spread originals...

Optional Equipment4-5
Paper Feeder
In addition to the cassette(s) provided with the main 
body, a paper feeder (with cassettes that can hold 300 
sheets each) can be used.
• The number of sheets t hat can be accommodated: 
300 sheets (standard paper, 64 to 105 g/m²).
• Paper sizes that can be set are: A3, B4, A4, A4R,  B5, B5R, A5R, Folio, 11 × 17 (Ledger), 8
1/2×14 
(Legal), 11 × 8
1/2, 81/2× 11 (Letter), 51/2×81/2 
(Statement), 8
1/2× 13 (Oficio II), 8K, and 16K
Copy paper can be set in the same way as...

Optional Equipment
4-6
Finisher
The finisher stores a large quantity of copies and can sort multiple copy sets by shifting the position 
of ejection for each one. It can also staple collated copy sets.
The number of sheets that can be st ored in the finisher and the specifications of stapling are shown 
below.
Names of Parts
1 Finisher tray
2 Process tray
3 Process tray extension
4 Finisher tray extension
5 Paper output guide 1
6 Paper output guide 2
Notes• Sorted copies are output onto the finisher...

Optional Equipment4-7
• The paper sizes are marked on the finisher tray extension. Open paper output guide 1 or 2 
according to the paper size.
• When stapling large paper such as A3, B4,  11 × 17 (Ledger), and 8
1/2× 14 (Legal), open the 
process tray extension to  prevent the paper from 
dropping.
Adding Staples
1
Open the stapler front cover toward your side.
2Pull out the staple holder.
3Remove the empty staple cartridge from the staple 
holder.
Downloaded From ManualsPrinter.com Manuals 

Optional Equipment
4-8
4While holding the staple holder with one hand and the 
new staple cartridge with the other hand, insert the 
cartridge into the holder with care about the direction.
NoteThe arrow on the staple cartridge indicates the insertion direction.
5Push the staple cartridge all the way into the holder and 
remove the paper tape around the staple cartridge by 
pulling it.
6Insert the staple holder into the insertion slot as it was. 
Insert it completely until it clicks.
7Close the stapler...

Optional Equipment4-9
2Remove the staple jammed at the end (side on which 
staples are set).
3Lower the face plate of the staple holder to its original 
position.
4Insert the staple holder  into the insertion slot as it was. Insert it completely until it clicks.
5Close the stapler front cover.
Job Separator
This unit is used to separate paper output destinations 
for easy classification. Copies are output to the output 
tray, and printer output is  ejected onto the job separator 
tray. Also the output...

Optional Equipment
4-10
Key Counter
The key counter is used to confirm the amount of 
usage of the copier functions. It is useful in managing 
copier usage for each departme nt, section, etc. as well 
as in the company overall.
Setting the Key Counter
Set the key counter securely in the key counter slot.
NoteIn the case where the key counter is used, no one will be able to make copies until it is installed in 
the machine.  Insert key counter  will be displayed when the key counter has not been securely...

Optional Equipment4-11
Additional Memory
A memory can be added for the copier functions an d the printer functions respectively. Adding a 
memory will increase the maximum number of originals that can be scanned at one time. Also 
complicated data can be printed. An additional memory of 64 MB or 128 MB is effective for originals 
containing photos with a low compression ratio.
Notes• Available memory For copier: 16 MB, 32 MB, 64 MB, 128 MB
For printer: 32 MB, 64 MB, 128 MB, 256 MB
• Number of originals...