Kyocera KM 3650w User Manual

							Chapter 3     Error Correction  3-18
3. 1. 3. 5     In Power Save Mode 
 
When “In Power Save Mode.” is displayed, KM-3650w is in the Power Save Mode to save the 
power consumption. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
(1)  The Power Save Mode works automatically if you make no operation for the time  
      specified in advance. 
      The machine ceases controlling the temperature of Fuser Unit completely to save the  
      power consumption. (Power Save Mode can save more power than Warm Sleep Mode.)
 
(2)  The Power Save Mode will be cancelled by the following 3 ways. 
•  Making a print from the network 
•  Inserting an original to the scanner 
•  Pressing any key on the Operation Panel 
      Note that it takes some minutes to recover from the Power Save Mode as the  
      temperature of Fuser Unit must be raised again. 
      (Print starts when the machine gets ready.) 
 
!  When the main switch is turned ON or during sleep mode recovery, the LCD takes 1 
     minute to display. 
     Please do not turn OFF the main switch during this period. 
Reference
 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-19
3. 2     Service Call Errors 
 
 
You will note an error message “A significant error occurred. Call the service” on the operation 
panel if the machine has the fatal error. 
At this time one of the following sub messages is displayed also. 
 
 Counter Error 
 Cutter Error 
  Developer Motor Error 
 FPGA Error 
  Fuser Low temp 
  Fuser Motor Error 
  Fuser Over temp 
 HV Charger Error 
  License Key Error 
 Main Motor Error 
 
 
 
 
 
 
PLEASE CALL YOUR TRAINED SERVICE PERSONNEL TO RESOLVE THESE ERRORS. 
 
 
If any of the above errors is displayed: 
 
 1.  Turn off the machine, wait approximately 30 seconds, and then turn on the machine again. 
 
 2.  If the same error message is displayed, turn off the machine, and then unplug the machine  
      from the wall outlet. 
      Call your service personnel. 
 
 
 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 4     Maintenance  4-1  
 
 
 
Chapter 4 
 
Maintenance 
 
 
Page 
4. 1     Cleaning of Each Part         4-  2 
   4. 1. 1     Scanner Unit                  4-  2 
   4. 1. 2     Print Engine                  4-  4 
   4. 1. 3     Operation Panel                  4-  6 
 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 4     Maintenance  4-2
4. 1     Cleaning of Each Part 
 
 
4. 1. 1     Scanner Unit 
 
Clean each Scan Glass, Feeding Rollers and Guide Plates once per a week, as the scan/copy 
image may become defective if these parts are dirty. 
 
 1.  Confirm that the machine is turned off. 
 
 
 2.  Open the Scanner Unit pulling up the Levers (1). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 3.  Wipe each Scan Glass (2) and Feeding Rollers (3) with a soft cloth. 
      Use the neutral detergent mixed with 50% of water as the cleaner. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
         NOTE 
 
Do not use organic solvent, glass cleaner and anti-static spray for the cleaning. 
1
23
3
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 4     Maintenance  4-3  4.  Wipe both the Upper Guide Plate (4) and the Lower Guide Plate (5) with a soft dry cloth. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 5.  Move the Scanner Unit a little to the rear side to unlock, and then close it. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
4
5
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 4     Maintenance  4-4
4. 1. 2     Print Engine 
 
Clean each Guide Film and Guide Plate once per a week, as the toner or paper dust may 
accumulates on such part which may result in a defective print image. 
 
 1.  Confirm that the machine is turned off. 
 
 
 2.  Open the Engine Unit pulling up the Engine Unit Open Levers (1). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 3.  Wipe each Guide Film (2) and Guide Plate (3) with a soft dry cloth to remove the toner or paper  
     dust. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2
3 
1
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 4     Maintenance  4-5  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 4.  Close the Engine Unit. 
 
 
 
 
 
 
 
 
 
 
 
 
         NOTE 
 
(1)  Photoconductive Drum (large green cylinder) right above the Guide Film. 
      You need to replace the Drum if damaged, as it is a very important part in creating the  
      print image. 
 
      Be careful about the following matters. 
 
         a.)  Do not touch the drum.  
               If you put your fingermark or oil on the Drum, it will cause for the defective image. 
 
         b.)  Take off such metal accessories as watch or ring.  
               You will have to replace the Drum if you damage the Drum scratching with such  
               accessories. 
 
         c.)  Do not leave the Upper Unit open for more than 10 minutes as the Drum is very  
               sensitive to light. (Direct sunlight is very harmful.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
(2)  Do not use water, organic solvent and alcohol for the cleaning. 
 Photoconductive Drum
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 4     Maintenance  4-6
4. 1. 3     Operation Panel 
 
Clean the Operation Panel once per a week. 
 
 1.  Confirm that the machine is turned off. 
 
 
 2.  Wipe the Operation Panel with a dry cloth. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
         NOTE 
 
Do not use water, alcohol, organic solvent and glass cleaner for the cleaning. 
Downloaded From ManualsPrinter.com Manuals 
						

							
For best results and machine performance, we re commend that you use only our original supplies for 
your products.
Downloaded From ManualsPrinter.com Manuals 
						

							Downloaded From ManualsPrinter.com Manuals