Kyocera KM 3650w User Manual

							Chapter 1     Before Use  1-8
1. 4. 2     Rear view 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
No. Name  Function 
1  Exit Cover  Open the Exit Cover to access the paper jam. 
2  LAN Port  Connects the KM-3650w to the network. 
    (Do not connect telephone line.) 
3 Dehumidify Heater Switch 
(Option) Turns on the Dehumidify Heater. 
4  Inlet Socket  Connect the Power Cord. 
5  Breaker  Shuts off the AC power. 
6  Print Guide Trays  Guide the prints to the Print Tray. 
 
1
6 2 
3 
4 
5 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 1     Before Use  1-9
1. 5     Specifications for the Scan Original 
 
 
A scan original must satisfy the following specifications. 
 
Thickness  0.05mm to 0.6mm 
Width 279.4mm to 914.4mm 
(11” to 36”) 
Length  210mm to 3,600mm 
 
 
Do not scan the following kinds of original, because you may damage the original or scanner itself! 
 
Sticked with paste   
Torn  
Folded (Leading edge)   
So much curled 
(Diameter is smaller than 
50mm.)  
 
 
 
 
Paste 
 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 1     Before Use  1-10  
Not square   
Wet image   
Made of metal or fabric   
Patched  
Clipped or stapled   
 
 
 
 
 
 
 
Wet 
Metal               Fabric 
Clipped            Stapled 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 1     Before Use  1-11  
Rough surface  
(Carbon paper for example)  
Punched  
 
 
  Rough surface
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 1     Before Use  1-12
1. 6     Specifications for the Printing Paper 
 
 
1. 6. 1     Papers not available to use 
 
Do not use the following kinds of printing paper because you may damage the print engine! 
 
So much curled paper   
Folded paper   
Creased paper   
Torn paper   
Punched paper   
 
 
 
 
 
 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 1     Before Use  1-13  
Paper that has already been 
used for printing   
Very slippery paper   
Very sticky paper   
Very thin and soft paper   
OHP Film   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
1. 6. 2     Keeping the paper in the custody 
 
Keep the paper in the custody taking care of the following matters. 
 
  1.  Do not expose the paper to the direct sunlight. 
  2.  Keep the paper away from high humidity. (It must be less than 70%) 
  3.  Put the paper on a flat place 
  4.  If you keep the paper in the custody, which you have already unpacked, put it into the  
       polyethylene bag to avoid the humidity. 
 
         CAUTION 
 
Do not use the paper with staple, or do not use such conductive paper as aluminium foil and 
carbon paper. 
Such paper may become cause for the fire. 
 
 
         
NOTE 
 
(1)  Print image may become light if printed on a paper of rough surface. 
 
(2)  Print image may become defective if the print paper is much curled. 
 
(3)  It will become a cause for paper jam, poor quality image or crease of paper if you  
      use a paper that does not satisfy the specification. 
 
(4)  Do not use a paper of which surface is very special, such as thermal paper, art paper,  
       aluminium foil, carbon paper and conductive paper. 
 
(5)  Tracing paper exposed to air over a long period tends to cause a defective printing. 
       Removing one round on the surface of the tracing roll paper from the beginning is  
       recommended. 
       Refer to the procedure 8 (on Page 2-7) of [2.3  Replacement of Roll Paper]. 
 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 1     Before Use  1-14
1. 6. 3     Measures against environmental condition 
 
Take measures to meet with the environmental condition as shown below. 
 
Humidity 
(%) Possible problem  Measures 
“Void of image”, “crease of paper” and 
other problems occurs when you print 
with plain paper and tracing paper. 
 1.  Install the humidifier in the room, and 
     humidify the room air. 
2.  Remove the paper from the machine  
     right after the completion of print, and  
     keep it in a polyethylene bag. 
“Void of image” occurs when you print 
with tracing paper. 
 If you will not make print soon, remove 
the tracing paper from the machine and 
keep it in a polyethylene bag. 
 
 
 Remove the paper from the machine after 
everyday use, and keep it in a 
polyethylene bag. 
“Void of image” occurs when you print 
with plain paper and tracing paper. 
 If you will not make print soon, remove 
the tracing paper from the machine and 
keep it in a polyethylene bag. 
Low 
 
 
 
 
 
 
 
40% 
 
 
70% 
 
 
 
 
 
 
High “Void of image”, “crease of paper” and 
other problems occurs when you print 
with plain paper and tracing paper. 1.  Turn on the Dehumidify Heater of the  
     KM-3650w. 
2.  Remove the paper from the machine  
     right after the completion of print, and  
     keep it in a polyethylene bag. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
         NOTE 
 
(1)  The machine is not equipped with the Dehumidify Heater initially as it is an optional part.
       (You need to purchase it separately.) 
       Turn it on when the humidity is higher than 65%. 
       Refer to [2. 8  Dehumidifying the Roll Paper (Option)] on page 2-18 for the detail. 
 
(2)  “Void of image” and “crease of paper” are the most popular problem you will encounter  
       when the humidity condition is very high or very low. 
Normal Print 
Normal Print If the media is humidified ;
If the media is humidified ;Crease of paper 
Void of image 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 2     Basic Operations  2-1  
 
 
 
Chapter 2 
 
Basic Operations 
 
 
Page 
2. 1     Turning on the Machine         2-  2 
 
2. 2     Turning off the Machine        2-  3 
 
2. 3     Replacement of Roll Paper        2-  4 
 
2. 4     Replacement of Toner Cartridge             2-  9 
 
2. 5     Set of Cut Sheet Paper to the Bypass Feeder     2- 13 
 
2. 6     Copying          2- 14 
 
2. 7     Emergent Stop of Scan or Copy       2- 15 
 
2. 8     Dehumidifying the Roll Paper (Option)      2- 16 
 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 2     Basic Operations  2-2
2. 1     Turning on the Machine 
 
 
 1.  Plug the machine into an exclusive wall outlet. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 2.  Press the Power Switch on the right side of the KM-3650w to turn on the machine. 
 
 
 
 
 
 
 
 
 
 
 
 
 
                                        Power Switch                                                         Press this side. 
 
 
 3.  The Ready Indicator lights when the KM-3650w gets ready. 
      Make scan, copy or print when it gets ready 
 
 
 
 
 
         WARNING 
 
(1)  Do not handle the Power Plug with wet hands, or you may receive an electrical shock. 
 
(2)  Make sure to earth the machine for your safety. 
 
(3)  Do not plug the printer into a multi-wiring connector in which other devices are  
      plugged. It may overheat the outlet and may result in a fire. 
 
(4)  The outlet must satisfy the following conditions. 
                  In U.S.A.   : 120V, plus/minus 10%, 50/60Hz and 15A 
                  In Europe  : 220-240V plus 6% or minus 10%, 50/60Hz and 10A 
         NOTE 
 
Scan function is option. 
 
!  When the main switch is turned ON or during sleep mode recovery, the LCD takes 
   1 minute to display. 
      Please do not turn OFF the main switch during this period. 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 2     Basic Operations  2-3
2. 2     Turning off the Machine 
 
 
 1.  Press the Power Switch on the right side of the KM-3650w to turn off the machine. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
                                        Power Switch                                         Press this side. 
 
 
 
 
 
 
 
 
 
 
 
         CAUTION 
 
Do not unplug the KM-3650w for 1 minute after turning it off. 
The Controller Unit requires 1 minute to completely shut down after you switch off 
the KM-3650w. 
Downloaded From ManualsPrinter.com Manuals