Kyocera KM 3650w User Manual

							Chapter 2     Basic Operations  2-14
2. 6     Copying 
 
 
 1.  Move the position of the Original Guides (1)  
      according to the width of original. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 2.  Put the original on the Original Table with face up. 
      Insert it under the Scanner Unit along with the original Guides. 
      When the leading edge touches the original feeding roller, the machine automatically carries  
      the original to scan its image. 
 
 
 
 
 
 
 
 
 
 
 
 
 
                                                                                                     Scan starts automatically. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
1
         NOTE 
 
(1) You need to press the Start Key on the  
     Operation Panel to start copying if the Auto  
     Start is OFF. 
 
 
 
 
 
 
 
 
 
 
                                                                                                                          Start Key 
 
(2) It the original is curled “up”, stretch the original well to make it be out of curl before setting 
      to the scanner. 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 2     Basic Operations  2-15
2. 7     Emergent Stop of Scan or Copy 
 
 
Press the Emergent Stop Button (1) on the Scanner Unit if you will stop scanning or copying 
emergently in the middle.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
1 
         NOTE 
 
The original is stopped at the time you press the Emergent Stop Button. 
The printing paper is cut at the same time and it is ejected. 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 2     Basic Operations  2-16
2. 8     Dehumidifying the Roll Paper (Option) 
 
 
If the roll paper is humidified, it may cause several kinds of poor quality. 
Poor quality you will experience most will be “crease of paper” and “void of image”. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Turn on the Dehumidify Heater if the room air is so humidified (higher than 65%) to prevent the 
above kinds of poor quality. 
You may be able to fix the above kinds of problem. 
 
 
 
 
 
 
 
 
 
 
To turn on the Dehumidify Heater, press the H side of the Dehumidify Heater Switch on the back of 
the machine. (Press its L side to turn off.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
                                                                                                        Dehumidify Heater Switch 
Normal Print 
Normal Print If the media is humidified ;
If the media is humidified ;Crease of paper 
Void of image 
         NOTE 
 
The machine is not equipped with the Dehumidify Heater initially as it is an optional part. 
Purchase the Dehumidify Heater separately and install to the machine if necessary. 
Ask to the service personnel for the detail. 
H (ON) 
L (OFF) 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-1  
 
 
 
Chapter 3 
 
Error Correction 
 
 
Page 
3. 1     Operator Call Errors           3-  2 
   3. 1. 1     Paper jam                   3-  2 
          3. 1. 1. 1     Paper jam in the Roll Deck. Set the roll paper correctly.     3-  2 
          3. 1. 1. 2     Paper jam in the bypass feeder. Remove the paper.      3-  5 
          3. 1. 1. 3     Paper jam in internal area. Open the cover, and remove the paper.  3-  6 
          3. 1. 1. 4     Paper jam in exit area. Open the cover, and remove the paper.   3-  8 
          3. 1. 1. 5     Original Jam. Open the cover, and remove the original.      3- 11 
   3. 1. 2     Open errors                  3- 12 
          3. 1. 2. 1     Cover is open. Close the Cover.  or  Printer is starting up.    3- 12 
          3. 1. 2. 2     Roll Deck is open. Close the Roll Deck.          3- 14 
          3. 1. 2. 3     Close the scanner cover.              3- 15 
   3. 1. 3     Other messages                  3- 16 
         3. 1. 3. 1     Set XX roll paper to the Roll Deck.          3- 16 
         3. 1. 3. 2     Set a paper to the bypass feeder.            3- 16 
         3. 1. 3. 3     Toner empty. Replace the toner cartridge.        3- 17 
         3. 1. 3. 4     In Warm Sleep Mode              3- 17 
         3. 1. 3. 5     In Power Save Mode              3- 18 
 
3. 2     Service Call Errors         3- 19 
 
 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-2
3. 1     Operator Call Errors 
 
 
3. 1. 1     Paper jam 
 
When a paper jam occurred, any of the following messages will be displayed. 
 
•  Paper jam in paper the Roll Deck. Set the roll paper correctly. 
•  Paper jam in the bypass feeder. Remove the paper. 
•  Paper jam in internal area. Open the cover, and remove the paper. 
•  Paper jam in exit area. Open the cover, and remove the paper. 
•  Original Jam. Open the cover, and remove the original. 
 
 
 
3. 1. 1. 1     Paper jam in the Roll Deck. Set the roll paper correctly. 
 
“Paper jam in the Roll Deck” is displayed when the roll paper is mis-fed in the Roll Deck. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 1.  Open the Roll Deck, and then rewind the roll paper. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-3  2.  Insert the leading edge of roll paper under the under the Guide Plate (1) until the edge touches  
      the feeding roller. 
      Rotate the Paper Feeding Knob (2) clockwise so that the feeding rollers catch the roll paper. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 3.  When the feeding rollers catch the paper, hold and pull the dent part (4) to the arrow direction  
      to open the paper guide, and rotate the Paper Feeding Knob (2) until the leading edge comes  
      out from the slit about 10cm. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
         NOTE 
 
(1)  If the leading edge is extremely torn or folded, cut it off with a cutter or scissors. 
 
(2)  Rotate the Paper Feeding Knob of rear  
      side (3) for the Roll 2. 
1 
2
3 
4 Leading edge 
of roll paper 
2 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-4  4.  Slide the Cutter Knob (5) fully from one side to  
      another side to cut the leading edge. 
      Remove the paper portion after cutting. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 5.  Rewind the roll paper a little to place the leading edge as the following photo. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 6. Close the Roll Deck finally. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
5
         NOTE 
 
Make sure to close the Roll Deck firmly until locked at the correct position. 
A paper jam may occur if not locked firmly. 
Place the leading 
edge here. 
         NOTE 
 
Slide the Cutter Knob completely until stopped at the end, or a paper jam occurs. 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-5
3. 1. 1. 2     Paper jam in the bypass feeder. Remove the paper. 
 
“Paper jam in the bypass feeder” is displayed when the cut sheet paper is mis-fed in the Bypass 
Feeder. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 1.  Pull up the Engine Unit Open Levers (1) to open the Engine Unit. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 2.  Remove the paper just pulling it frontward. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 3.  Close the Engine Unit. 
 
 
 
 
 
 
 
 
 
 
 
1 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-6
3. 1. 1. 3     Paper jam in internal area. Open the cover, and remove the  
                   paper. 
 
“Paper jam in internal area” is displayed when the paper is mis-fed in internal area of the machine. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 1.  Pull up the Engine Unit Open Levers (1) to open the Engine Unit. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 2.  Remove the mi-fed paper (2). 
 
 
 
 
 
 
 
 
 
 
 
 
 
1 
2
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-7  3.  Close the Engine Unit firmly. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
         NOTE 
 
Make sure to close the Engine Unit firmly until locked at the correct position. 
Downloaded From ManualsPrinter.com Manuals