Kyocera KM 3650w User Manual

							Chapter 2     Basic Operations  2-4
2. 3     Replacement of Roll Paper 
 
 
Roll 2 is an optional part. 
The machine is equipped with the Roll 2 in the following instruction. 
 
 
 
 
 
 
 
 
 1.  Pull up the Lever (1) and draw out the Roll Deck (2). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 2.  Remove the Roll Spool (3) with paper core from the Roll Deck. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
1 
3 
         NOTE 
 
Confirm that the machine has finished the printing operation completely before opening the 
Roll Deck. 
If you open it during printing, a paper jam may occur. 
         NOTE 
 
Note that a paper jam tends to occur at the time of roll end. 
2
3
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 2     Basic Operations  2-5  3.  Press down the Lever (4) to release the paper core, and then pull out the Roll Spool (3) from  
      the paper core. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 4.  Loosen the knob (5), slide the position of Paper Guide (6) according to the width of roll paper  
      you will set, and then fix the Paper Guide (6) tightening the knob (5). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
4 
3 
         NOTE 
 
Align the triangle mark (7) of the Paper Guide  
with each size guide (8). 
5 
6 
8
7
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 2     Basic Operations  2-6  5.  Pressing down the Lever (4), insert the Roll Spool (3) to the core of new roll paper. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 6.  Install the Roll Spool (3) with new roll paper to the  
      Roll Deck. 
 
 
 
 
 
 
 
 
 
4 3 
         NOTE 
 
(1)  Be careful of the winding direction of roll paper at this time. 
 
 
(2)  Try to rotate the Roll Spool after inserting to  
      the roll paper to check whether or not it  
      firmly holds the roll paper. 
 
 
 
 
 
 
 
 
 
 
      Move up the Lever (4) if the paper is not held  
      firmly. 
      A paper jam may occur if it is not held firmly. 
3
4
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 2     Basic Operations  2-7  7.  Insert the leading edge of roll paper under the Guide Plate (9) until the edge touches the  
      feeding roller. 
      Then rotate the Paper Feeding Knob (10) clockwise so that the feeding rollers catch the roll  
      paper. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 8.  When the feeding rollers catch the paper, hold and pull the dent part (12) to the arrow direction  
      to open the paper guide, and rotate the Paper Feeding Knob (10) until the leading edge comes  
      out from the slit about 10cm. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
         NOTE 
 
In case of Roll 2, rotate the Paper Feeding Knob 
of rear side (11). 
9 
Leading edge 
of roll paper 
11 
10
10 
12 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 2     Basic Operations  2-8  9.  Slide the Cutter Knob (12) fully from one side to  
      another side to cut the leading edge. 
      Remove the paper portion after cutting. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
10. Rewind the roll paper a little to place the leading edge as the following photo. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
11. Close the Roll Deck (2) finally. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Place the leading 
edge here. 
2 
12
         NOTE 
 
Slide the Cutter Knob completely until stopped at the end, or a paper jam occurs. 
         NOTE 
 
Make sure to close the Roll Deck firmly until locked at the correct position. 
A paper jam may occur if not locked firmly. 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 2     Basic Operations  2-9
2. 4     Replacement of Toner Cartridge 
 
 
 1.  Open the Toner Hatch (Original Table) (1). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 2.  Slide the green Lever (2) to the right to unlock the Toner Cartridge. 
      (Lever (2) is held automatically.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
1
2 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 2     Basic Operations  2-10  3.  Pressing down the Cartridge Lock Lever (3), rotate  
      the body (4) of cartridge to the arrow direction  
      some revolutions until it stops. 
      (You can close the toner supplying hole of the  
      cartridge firmly by this treatment.) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 4.  Pressing down the Cartridge Lock Lever (3), bring  
      up the left side of the Toner Cartridge first , and  
      then remove the whole cartridge from the machine. 
 
 
 
 
 
 
 
 
 
 
 
 
         NOTE 
 
The toner may drop from the toner supplying  
hole, and it may scattered into the machine or  
on the floor if you remove the Toner Cartridge  
without closing the toner supplying hole (5). 
3
5
34 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 2     Basic Operations  2-11  5.  Shake the new Toner Cartridge several times left  
      and right to make the toner smooth. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 6.  Pressing down the Cartridge Lock Lever (3), fit the pin (6) on the left side of cartridge to the  
      groove (7) on the machine side. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
         NOTE 
 
Confirm that the Cartridge Lock Lever (3) firmly locks the Toner Cartridge at the correct 
position. (It must be at a level position.) 
 
                             Good                                                                 No good 
 
 
 
 
7 
6 
3
Press down completely.
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 2     Basic Operations  2-12  7.  Rotate the body (4) of the cartridge to the arrow  
      direction some revolutions to open the toner  
      supplying hole. 
      (You may feel tight when rotating the body (4).) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 8.  Close the Toner Hatch (Original Table) (1) finally. 
 
 
 
 
 
 
 
 
 
 
 
         NOTE 
 
(1)  Confirm that the projection (8) is fitted into  
      the notch (9). 
 
 
 
 
 
 
 
 
 
 
 
 
(2)  The Lever (2) may not lock the cartridge at  
      this point of time, as it rotates and locks the  
      cartridge automatically when Toner Hatch 
      (Original Table) is closed. 
8 
9
1
2 
4 
4 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 2     Basic Operations  2-13
2. 5     Set of Cut Sheet Paper to the Bypass  
           Feeder 
 
 
 1.  Open the Bypass Feeder (1). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 2.  Put the cut sheet paper on the table along with the concerning size mark, and then insert it into  
      the Bypass Feeder. 
      When the paper touches the feeding roller, the machine automatically carries and sets the  
      paper at the proper position. 
 
 
 
 
 
 
 
 
 
 
 
 
1
Downloaded From ManualsPrinter.com Manuals