Kyocera KM 3650w User Manual

							Chapter 3     Error Correction  3-8
3. 1. 1. 4     Paper jam in exit area. Open the cover, and remove the paper. 
 
“Paper jam in exit area” is displayed when the paper is mis-fed in the exit area. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 1.  Pull up the Engine Unit Open Levers (1) to open the Engine Unit. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
1 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-9  2.  Check the position of the paper in the machine. 
 
      If the paper is accessible from the front side as the  
      right photo, go to the following procedure 3. 
 
 
 
 
 
 
 
 
 
 
 
 
      If the paper is impossible to access from the front side because the end of paper is deep in the  
      machine as the following photo, go to the following procedure 4. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 3.  Simply pull out the paper to the front side when  
      accessible from the front side. 
 
 
 
 
 
 
 
 
 
 
 
 
 
Paper 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-10  4.  If the paper is not accessible from the front side, hold both handles (2) and open the Exit  
      Cover (3). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 5.  Remove the paper pulling to the rear side. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
2
         WARNING 
 
Do not touch any part in the Exit Cover because some parts are extremely hot, or you will be 
burnt. 
Also be careful not to get burnt when you touch the printing paper as it may be very hot. 
 
 
         
NOTE 
 
Toner may be sticking on the Fuser Roller after removing the mis-fed paper. 
This toner may be fused onto the next printing paper. 
3
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-11
3. 1. 1. 5     Original Jam. Open the cover, and remove the original. 
 
“Original jam” is displayed when the original is mis-fed in the Scanner Unit. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 1.  Open the Scanner Unit pulling up the Levers (1), and then remove the original. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 2.  Open the scanner cover backward to unlock the cover, and then close it. 
 
 
 
 
 
 
 
 
 
 
 
 
 
1 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-12
3. 1. 2     Open errors 
 
When any cover or unit of the machine is open, any of the following messages will be displayed. 
 
•  Cover is opened. Close the Cover.  or  Printer is starting up. 
•  Roll Deck is open. Close the Roll Deck. 
•  Close the scanner cover. 
 
 
 
3. 1. 2. 1     Cover is open. Close the Cover.  or  Printer is starting up. 
 
“Cover is open” is displayed when either Engine Unit or Toner Hatch (Original Table) is open. 
This message is also displayed when the machine is in the middle of starting up. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 1.  Check if the Engine Unit is closed (locked) firmly. 
      If not, close it firmly. 
 
 
 
 
 
 
 
 
 
 
 
 
         NOTE 
 
The Engine Unit may be opened slightly  
(unlocked) even if it looks closed firmly. 
Engine Unit 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-13  2.  Check if the Toner Hatch (Original Table) is closed  
      firmly. 
      If not, close it firmly. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 3.  If the same error message is displayed although both Engine Unit and Toner Hatch (Original  
      Table) are closed firmly, the machine is in the start up process. 
      Wait for a while until the error message disappears automatically. 
         NOTE 
 
The Toner Hatch (Original Table) may be 
opened slightly even if it looks closed firmly. 
Toner Hatch 
(Original Table)
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-14
3. 1. 2. 2     Roll Deck is open. Close the Roll Deck. 
 
“Roll Deck is open” is displayed when the Roll Deck is open. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 1.  Check if the Roll Deck is closed firmly. 
      If not, close it firmly. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
         NOTE 
 
The Roll Deck may be opened slightly even if it looks closed firmly. 
Roll Deck 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-15
3. 1. 2. 3     Close the scanner cover. 
 
“Close the scanner cover.” is displayed when the Scanner Unit is open. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 1.  Check if the Scanner Unit is closed firmly. 
      If not, close it firmly. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
         NOTE 
 
The Scanner Unit may be opened slightly even if it looks closed firmly. 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-16
3. 1. 3     Other messages 
 
The following messages will be displayed according to the situation. 
 
•  Set XX roll paper to the Roll Deck. 
•  Set a paper to the bypass feeder. 
•  Toner empty. Replace the toner cartridge. 
•  In Warm Sleep Mode 
•  In Power Save Mode 
 
 
 
3. 1. 3. 1     Set XX roll paper to the Roll Deck. 
 
When “Set XX roll paper to the Roll Deck” is displayed, set the roll paper of required size to the 
Roll Deck. 
(“XX” stands for the paper width.) 
Refer to [2.3  Replacement of Roll Paper] on page 2-4 for the way to set the roll paper. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
3. 1. 3. 2     Set a paper to the bypass feeder. 
 
When “Set a paper to the bypass feeder” is displayed, set a cut sheet paper to the Bypass Feeder. 
Refer to [2.5  Set of Cut Sheet Paper to the Bypass Feeder] on page 2-13 for the way to set the cut 
sheet paper. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3     Error Correction  3-17
3. 1. 3. 3     Toner empty. Replace the toner cartridge. 
 
When “Toner empty.” is displayed, replace the Toner Cartridge with the new one. 
Refer to [2.4  Replacement of Toner Cartridge] on page 2-9 for the way to replace the Toner 
Cartridge. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
3. 1. 3. 4     In Warm Sleep Mode 
 
When “In Warm Sleep Mode.” is displayed, KM-3650w is in the Warm Sleep Mode to save the 
power consumption. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
(1)  The Warm Sleep Mode works automatically if you make no operation for the time  
      specified in advance. 
      The temperature maintained on the Fuser Unit is fallen down great degrees to save the  
      power consumption. 
 
(2)  The Warm Sleep Mode will be cancelled by the following 3 ways. 
•  Making a print from the network 
•  Inserting an original to the scanner 
•  Pressing any key on the Operation Panel 
      Note that it takes some minutes to recover from the Warm Sleep Mode as the  
      temperature of Fuser Unit must be raised again. 
      (Print starts when the machine gets ready.) 
Reference
 
Downloaded From ManualsPrinter.com Manuals