Kyocera FS C5400DN User Manual

Troubleshooting 6-17
2Remove the jammed paper. 
Paper Jam in Printer
Paper is jammed at the paper cassette or inside the printer. Remove the 
jammed paper using the procedure given below.
CAUTION  The fuser unit inside the printer is hot. Do not touch it with 
your hands as it may result in burn injury. Remove jammed paper 
carefuly.
1Press the lever to release the lock.
 
2Pull the front cover towards you.
3If the paper has jammed near the registration roller, as shown in A, 
remove the paper by pulling...

6-18Troubleshooting 
If the paper has jammed inside the fuser unit, as shown in B, open 
the fuser cover and remove the paper by pulling its edge.
If the paper has jammed inside the duplex unit, as shown in C, lift the 
duplex unit and remove the paper by pulling it up from the edge.
4Close the front cover. 
B
Fuser 
Cover
C
Duplex Unit
Downloaded From ManualsPrinter.com Manuals 

Troubleshooting 6-19
Paper Jam at Cassette 2 (to 5)
Paper is jammed in the optional cassette. Remove the jammed paper 
using the procedure given below.
Pull out the optional cassette and remove the jammed paper.
Downloaded From ManualsPrinter.com Manuals 

6-20Troubleshooting 
Downloaded From ManualsPrinter.com Manuals 

 A-1
Appendix
This chapter lists the provides details of the available interfaces 
and describes the optional hardware that can be installed on 
the printer and shows the printers specifications.
Interface A-2
USB Interface A-2
Network Interface A-3
About the Options A-5
Expansion Memory Modules A-6
General Description of Options A-9
Specifications A-12
For availability of the options, consult your service technician.
Downloaded From ManualsPrinter.com Manuals 

A-2 
Interface
This chapter explains the signals used in the printers USB, and network 
interfaces. It also lists pin assignments, signal functions, timings, 
connector specifications, and voltage levels.
• USB Interface
• Network Interface
USB Interface
This printer supports the Hi-Speed USB. USB (Universal Serial Bus) 
interface specifications and interface signals are as follows.
Specifications
Basic Specification
Complies with the Universal Serial Bus Specification Revision 2.0.
Connectors
Printer:...

 A-3
Network Interface
Features
Automatic IP Address Resolution
This feature is compatible with the DHCP/DHCPv6 protocol and allows 
the printer to automatically receive IP addresses from the DHCP/DHCPv6 
server. 
Management using Web Browsers
HTTP pages are incorporated in to the interface, so that a web browser 
can be used to monitor and change a range of settings. The settings can 
be password-protected.
Support for a Range of Protocols
The SMTP, POP3, SSL, SNMP, IPv6 and NetBIOS over TCP/IP...

A-4 
Operation Environment
10 to 35 °C (50 to 95 °F), 20-80 % RH (condensation-free)
EMI Countermeasures
VCCI Class B, FCC Class B (U.S.), CE (Europe)
IMPORTANT  When IPv6 functions are used, the devices used on the 
network (routers, PCs, etc) must support IPv6.
Downloaded From ManualsPrinter.com Manuals 

 A-5
About the Options
This printer has the following options available to satisfy your printing 
requirements. For instructions on installing individual options, refer to the 
documentation included with the option. Some options are explained in 
the following sections.
Paper Feeder 
PF-500/ PF-510
Memory Card (CF)
Expansion Memory
(DIMM 128/256/512/
1024 MB)Hard Disk
HD-5ABase CA-500
USB memory
Downloaded From ManualsPrinter.com Manuals 

A-6 
Expansion Memory Modules
The printers main controller board has a memory slot into which you can 
plug in optional memory modules (dual in line memory modules). You can 
increase the printers memory up to 1280 MB by plugging in the optional 
memory modules. 
Expansion Memory Modules
You can select additional memory modules from 128, 256, 512 or 
1024 MB. The maximum memory size is 1024 MB.
Precautions for Handling the Printers Main Controller Board 
and Memory Modules
To protect electronic parts,...