Kyocera FS 9130DN User Manual

							Maintenance 
OPERATION GUIDE3-5
3Grasp the handle on the toner container, push the lock lever up again and 
gently lift the toner container.
4Seal up the old toner container with the supplied plastic bag and dispose 
of it.
5Lightly tap the new toner on the top 5 to 6 times.
Downloaded From ManualsPrinter.com Manuals 
						

							Maintenance 
3-6OPERATION GUIDE
6Thoroughly shake the toner container (in the direction of the arrows) ten 
times or more to loosen and mix the toner inside.
7Grasp the handle on the toner container and insert the toner container 
along the rail of the printer.
When inserting, be sure that the gear side of the toner container faces the 
printer. Leave the front cover open to allow insertion of the waste toner 
box.
Gear Side
To the Printer
Downloaded From ManualsPrinter.com Manuals 
						

							Maintenance 
OPERATION GUIDE3-7
8Hold the toner container using both hands and fully insert it into the printer.
9Close the front cover.
Replacing the Waste Toner Box
When replacing the toner container, the used waste toner box in the printer 
should also be replaced with the new one from the new toner kit. The 
printer will not operate without replacing the waste toner box.
1Open the printer front cover all the way.
2Remove the old waste toner box as shown in the figure.
Downloaded From ManualsPrinter.com Manuals 
						

							Maintenance 
3-8OPERATION GUIDE
3Remove the seal from the rear of the old waste toner box, and then close 
the opening of the box with the seal. Seal up the old waste toner box with 
the supplied plastic bag and dispose of it.
4Fit the new waste toner box to the printer.
5Close the front cover.
Downloaded From ManualsPrinter.com Manuals 
						

							Maintenance 
OPERATION GUIDE3-9
Cleaning the Printer
Cleaning the Filters
When replacing the toner container, also clean the filters.
1Open the MP tray.
2Remove the filters from the printer. Press in the tabs on the top filter while 
removing it.
3Press in the tab on the right filter while removing it.
Downloaded From ManualsPrinter.com Manuals 
						

							Maintenance 
3-10OPERATION GUIDE
4Clean the filters with a vacuum cleaner.
Do not wash the filters nor use the cleaning brush supplied with the 
machine. 
5After cleaning, replace the filters in their original positions.
After cleaning the filters, proceed to next section.
Downloaded From ManualsPrinter.com Manuals 
						

							Maintenance 
OPERATION GUIDE3-11
The Inside of the Printer
To avoid print quality problems, the interior of the printer must be cleaned.
1Open the front cover all the way.
2Remove the blue colored cleaning brush.
3Pull up the lock lever on the left side of the printer, and open the left cover 
1.
Downloaded From ManualsPrinter.com Manuals 
						

							Maintenance 
3-12OPERATION GUIDE
4Clean the separator by moving the cleaning brush from left to right along 
with the separator.
NOTE: When removing jammed paper, be careful not to touch the printer 
drum. This can cause printer malfunction.
5While rotating the transfer roller with the gear on its left, move the cleaning 
brush back and forth along the transfer roller to remove soiling as shown. 
After cleaning, return the cleaning brush to its storage space, and close the 
left cover 1 and the front cover.
Downloaded From ManualsPrinter.com Manuals 
						

							OPERATION GUIDE4-1
4 Troubleshooting
This chapter explains how to handle printer problems that may 
occur. If a problem cannot be corrected, contact your service 
representative.
This chapter explains the following topics:
•General Guideline .......................................................  4-2
•Print Quality Problems.................................................  4-4
•Indicators and Messages ............................................  4-7
•Correcting a Paper Jam ............................................  4-14
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting 
4-2OPERATION GUIDE
General Guideline
If some kind of problem should occur, check the following before 
concluding the printer is broken;
SymptomCheck ItemsCorrective Action
The printer will not 
print from the 
computer.Check the READY 
indicator.OffLook through the items below and check 
anything that seems appropriate.
FlashingAn error has occurred. Check the message 
display, and then take measures referring to 
Indicators and Messages on page 4-7.
LitRefer to the appropriate item below.
Check the  
ATTENTION 
indicator.
FlashingRefer to Indicators on page 4-7.
Lit
A maintenance message appears in 
the message display.Refer to Maintenance Messages on page 4-7.
Print quality is not good. Clean the filters.
Refer to Print Quality Problems on page 4-4.
Paper is jammed.Refer to Correcting a Paper Jam on page 4-14.
Nothing lights on 
the operation panel 
even when power is 
turned on and the 
fan makes no 
noise.Check that the power cord is 
properly plugged into the power 
outlet.Turn off the printer’s power, plug in the power 
cord securely, and try turning on the printer’s 
power again.
Check that the main switch is really in the ON ( | ) position.
The printer prints a 
status page, but 
data from the 
computer is not 
being printed 
normally.Check the interface cable.Connect both ends of the interface cable 
securely. Try replacing the printer cable.
Check program files and application 
software.Try printing another file or using another print 
command. If the problem occurs only with a 
specific file or application, check the printer 
settings for that application.
Downloaded From ManualsPrinter.com Manuals