Home > Kyocera > Printer > Kyocera FS 9130DN User Manual

Kyocera FS 9130DN User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Kyocera FS 9130DN User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 73 Kyocera manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Machine Parts 
    OPERATION GUIDE1-3
    Components at the Left and the Rear of the Printer
    15 Power Cord Connector
    16 Option Unit Connector
    17 Handles for Transport
    18 Left Cover 2
    19 Lock Lever
    20 Left Cover 1
    1617 18 20
    19
    15
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Machine Parts 
    1-4OPERATION GUIDE
    Components at the Right of the Printer
    21 Memory Card Slot
    22 Option Interface Slot (OPT)
    23 Option Memory Slot Cover
    24 USB Memory Slot (A1)
    25 Parallel Interface Connector
    26 Option Hard Disk Unit Slot (HDD)
    27 Network Interface Connector
    28 USB Interface Connector (B1)
    21
    22
    23
    2
    4
    25
    26
    2
    7
    28
    Downloaded From ManualsPrinter.com Manuals 
    						
    							OPERATION GUIDE2-1
    2 Printing Operation
    This chapter contains explanations on the following topics:
    •Loading Printer Driver .................................................  2-2
    •Printing from Application Software ..............................  2-3
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Printing Operation 
    2-2OPERATION GUIDE
    Loading Printer Driver
    Ensure the printer is plugged in and connected to the PC before installing 
    the printer driver from the CD-ROM.
    1Switch on the PC and activate Windows.
    NOTE:If the Welcome to the Found New Hardware Wizard dialog box 
    displays, select Cancel.
    2Insert the CD-ROM supplied with the printer into the optical drive of the PC.
    3The installation program launches.
    NOTE:If the installation program fails to launch, use Windows Explorer 
    to access the CD-ROM and select Setup.exe.
    4Perform the procedures displayed on the installation program to install the 
    KX DRIVER.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Printing Operation 
    OPERATION GUIDE2-3
    Printing from Application Software
    The steps required to print a document created with an application are 
    explained below. You can select the printing Paper Size and Output 
    Destination.
    1Load the paper required into the paper cassette.
    2From the application File menu, select Print. The Print dialog box 
    displays.
    3Click the drop down list of printer names. All the printers installed in 
    Windows are listed. Click the name of the machine.
    4Use Number of copies to enter the number of prints required. Up to 999 
    copies can be entered.
    For Microsoft Word, we recommend that you click Options and specify 
    Use printer settings for the Default tray.
    5To start printing, click OK.
    3
    4
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Printing Operation 
    2-4OPERATION GUIDE
    Downloaded From ManualsPrinter.com Manuals 
    						
    							OPERATION GUIDE3-1
    3 Maintenance
    This chapter contains explanations on the following topics:
    •General Information.....................................................  3-2
    •Toner Container Replacement.....................................  3-3
    •Cleaning the Printer.....................................................  3-9
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Maintenance 
    3-2OPERATION GUIDE
    General Information
    This chapter describes basic maintenance tasks you can perform on the 
    printer. You can replace the following component according to the printers 
    display:
    • Toner Container
    • Waste Toner Box
    Also, the internal parts need periodic cleaning.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Maintenance 
    OPERATION GUIDE3-3
    Toner Container Replacement
    The toner container in the printer should be replaced as soon as the 
    message display shows Toner low or soon after. If you continue to use 
    the printer, eventually the toner supply will be exhausted at which point the 
    printer will stop printing and the Replace toner Clean printer 
    message will be shown instructing you to install a new toner kit.
    Frequency of toner container replacement
    Assuming an average toner coverage of 5 % and EcoPrint mode turned 
    off, the toner container will need replacing approximately once every 
    40,000 pages.
    Starter Toner Container
    The toner container packed with the new printer is a starter toner container. 
    The starter toner container lasts an average of 20,000 pages.
    Toner Kits
    For best results, we recommend that you only use genuine Kyocera Parts 
    and Supplies.
    A new toner kit contains the following items:
    • Toner Container
    • Cleaning cloth
    • Plastic waste bags for old toner container and old waste toner box
    • Waste toner box
    NOTE: Be sure to clean the inside of the printer when replacing the toner 
    container.
    Understanding Messages Requesting Toner Container Replacement
    The printer displays messages at two stages of toner usage. This message 
    is automatically alternated with the other printer message (such as 
    Ready):
    • When the printer becomes low on toner, the printer displays the 
    message Toner low as the first caution. Note the replacement is not 
    always necessary at this stage.
    • If you ignore the above message and continue printing, the printer 
    displays the message Replace toner - just before the toner is used 
    up. The toner container must be replaced immediately. After the 
    cleaning is finished, however, the message does not 
    automaticallychange to Ready. To restart printing, you must press 
    [GO] and make the printer ready.
    Downloaded From ManualsPrinter.com Manuals 
    						
    							Maintenance 
    3-4OPERATION GUIDE
    Replenishing Toner
    This section explains how to replace the toner container. When replacing 
    the toner container, always replace the waste toner box at the same time.
    If this box is full, the printer may be damaged or contaminated by the waste 
    toner that may spill over the box.
    NOTE: During toner container replacement, temporarily put storage 
    media and computer supplies (such as floppy disks) away from around 
    the toner container. This is to avoid damaging media by the magnetism of 
    toner.
     
    You do not have to turn printer power off before starting the replacement. 
    Any data that may be under printing process in the printer will be deleted if 
    you turn printer power off.
    1Open the printer front cover all the way.
    2Push the lock lever up and gently remove the toner container until its 
    handle appears.
    NOTE: Do not pull the toner container all the way as it can fall off and the 
    toner spots the floor.
    Downloaded From ManualsPrinter.com Manuals 
    						
    All Kyocera manuals Comments (0)

    Related Manuals for Kyocera FS 9130DN User Manual