Kyocera FS 9130DN User Manual

							 
OPERATION GUIDEix
guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, 
the user is encouraged to try to correct the interference by one or more of 
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that 
used for the receiver.
• Consult your service technician or an experienced radio/TV technician 
for help.
Changes or modifications not expressly approved by the manufacturer for 
compliance could void the users authority to operate the equipment. 
Shielded circular cables should be used for interfacing with the computer.
Precautions for Use
Any modifications without prior permission of Kyocera may cause harmful 
interference.
If any modifications or changes are made to this equipment without prior 
permission of Kyocera, Kyocera as the manufacturer does not guarantee 
the compliance with the FCC Rules. The use of equipment that does not 
comply with the FCC Rules is prohibited.
Downloaded From ManualsPrinter.com Manuals 
						

							 
xOPERATION GUIDE
Safety Information
Laser Safety
This printer is certified as a Class 1 laser product under the U.S. 
Department of Health and Human Services (DHHS) Radiation 
Performance Standard according to Radiation Control for Health and 
Safety Act of 1968. This means that the printer does not produce 
hazardous laser radiation. Since radiation emitted inside the printer is 
completely confined within protective housings and external covers, the 
laser beam cannot escape from the printer during any phase of user 
operation.
Laser Notice
This printer is certified in the U.S. to conform to the requirements of DHHS 
21 CFR Subchapter for Class I (1) laser products, and elsewhere is 
certified as a Class I laser product conforming to the requirements of IEC 
825.
DANGER:CLASS 3B LASER RADIATION WHEN OPEN. AVOID 
DIRECT EXPOSURE TO BEAM.
CAUTION: Use of controls or adjustments or performance of procedures 
other than those specified herein may result in hazardous radiation 
exposure.
Radio Frequency Transmitter
This machine contains the transmitter module. We, the manufacturer 
(Kyocera Corporation) hereby declare that this equipment (page printer), 
model FS-9130DN and FS-9530DN are in compliance with the essential 
requirements and other relevant provisions of Directive 1999/5/EC.
Radio Tag Technology
In some countries the radio tag technology used in this equipment to 
identify the toner container may be subject to authorization and the use of 
this equipment may consequently be restricted.
Downloaded From ManualsPrinter.com Manuals 
						

							
 
OPERATION GUIDExi
Caution Labels
Caution labels have been attached to the copier at the following locations 
for safety purposes. Be sufficiently careful to avoid fire or electric shock 
when removing a paper jam or when replacing toner.
NOTE: Do not remove these labels.
High temperature inside. Do not 
touch parts in this area, because 
there is a danger of getting burned.
Do not incinerate toner and toner 
container. Dangerous sparks may 
cause burn. Moving parts inside. May cause 
personal injury. Do not  touch 
moving parts.
High temperature inside. Do not 
touch parts in this area, because 
there is a danger of getting burned.
Label inside the printer (Laser 
radiation warning)
Downloaded From ManualsPrinter.com Manuals 
						

							
For U.S.A.  
and Canada For Europe, Asia, 
 
and other countries
 
xii OPERATION GUIDE
CDRH Regulations
The Center for Devices and Radiological Health (CDRH) of the U.S. Food 
and Drug Administration implemented regulations for laser products on 
August 2, 1976. These regulations apply to laser products manufactured 
after August 1, 1976. Compliance is mandatory for products marketed in 
the United States. A label indicating  compliance with the CDRH regulations 
must be attached to laser products ma rketed in the United States. On this 
machine, the label is on the right.
Ozone Concentration
The printers generate ozone gas (O3) which may concentrate in the place 
of installation and cause an unpleasant smell. To minimize the 
concentration of ozone gas to less than 0.1ppm, we recommend you not 
to install the printer in a confined area where ventilation is blocked.
Declaration of Conf ormity for U.S.A.
Model name: Page Printer FS-9130DN/FS-9530DN 
Trade name: Kyocera Mita 
Responsible party: Kyocera Mita America, Inc. 
Address: 225 Sand Road PO Box 40008 Fairfield, New Jersey 07004-
0008, U.S.A.
 
Telephone: (973) 808-8444 
Fax: (973) 882-6000
Manufacturer: Kyocera Mita Corporation 
Manufacturers address: 2-28, 1-Chom e, Tamatsukuri, Chuo-ku, Osaka, 
540-8585, Japan
This device complies with Part 15 of  the FCC Rules. Operation is subject 
to the following two conditions: (1)  this device may not cause harmful 
interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.
Downloaded From ManualsPrinter.com Manuals 
						

							 
OPERATION GUIDExiii
The manufacturer and its merchandising companies retain the following 
technical documentation in anticipation of the inspection that may be 
conducted by the authorities concerned.
User’s instruction that conforms to the applicable specifications. 
Technical drawings. 
Descriptions of the procedures that guarantee the conformity. 
Other technical information.
Kyocera Mita America Inc.
CE Marking Directive
According to Council Directive 89/336/EEC, 73/23/EEC, and 1999/5/EC
Manufacturer: Kyocera Mita Corporation 
Manufacturers address: 2-28, 1-Chome, Tamatsukuri, Chuo-ku, Osaka, 
540-8585, Japan
Declares that the product
Product name: Page Printer
Model number: FS-9130DN/FS-9530DN (as tested with enhancement 
optional unit; Dual Paper Feeder PF-700, Large Capacity Paper Feeder 
PF-750, Document Finisher DF-710/DF-730, Booklet Unit BF-710, Mail 
Bin MT-710, and Punch Unit PH-5A)
Conforms to the following product specifications:
EN 55 022:1998+A1:2000+A2:2003 Class B
EN 61 000-3-2:2000
EN 61 000-3-3:1995+A1:2001
EN 55 024:1998+A1:2001+A2:2003
EN 60 950-1:2001+A11
EN 60 825-1:1994+A1+A2
EN 300330-1
EN 300330-2
The manufacturer and its merchandising companies retain the following 
technical documentation in anticipation of the inspection that may be 
conducted by the authorities concerned.
User’s instruction that conforms to the applicable specifications. 
Technical drawings. 
Descriptions of procedures that guarantee conformity. 
Other technical information.
Downloaded From ManualsPrinter.com Manuals 
						

							 
xivOPERATION GUIDE
Declaration of Conformity (Australia)
Manufacturer: Kyocera Mita Corporation 
Manufacturers address: 2-28, 1-Chome, Tamatsukuri, Chuo-ku, Osaka, 
540-8585, Japan
declares that the product
Product name: Page Printer 
Model name:    FS-9130DN/FS-9530DN
Description of devices: This Page Printer Model FS-9530DN is the 51ppm 
(FS-9130DN is the 40ppm); A4 size and utilized plain paper; dry toner; etc. 
The printer can be equipped with several enhancement optional unit as a 
dual paper feeder as PF-700, large capacity paper feeder as PF-750, DF-
710/DF-730 as document finisher, booklet unit as BF-710m mail bin as 
MT-710, and punch unit as PH-5A.
conforms to the following product specifications:
AS/NZS 3548: 1995 (EN 55 022: 1998 Class B)
AS/NZS 4268: 2003
IEC60950: 1999 (EN 60 950: 2000)
The manufacturer and its merchandising companies retain the following 
technical documentation in anticipation of the inspection that may be 
conducted by the authorities concerned.
User’s instruction that conforms to the applicable specifications 
Technical drawings 
Descriptions of procedures that guarantee conformity 
Other technical information
The manufacturer has been employed with ISO9001 scheme. JQA and BS 
have attested the manufacturer.
Kyocera Mita Australia Pty., Ltd. 
6-10 Talavera Road, North Ryde, NSW 2113, Australia 
Telephone: +61 2-9888-9999 
Fax: +61 2-9888-9588
Canadian Department of Communications Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Avis de conformité aux normes du ministere des Communications du 
Canada 
Cet appareil numérique de la classe B est conforme a la norme NMB-003 
du Canada.
Downloaded From ManualsPrinter.com Manuals 
						

							
 
OPERATION GUIDExv
EN ISO 7779
Maschinenlärminformations-Verordnung 3. GPSGV, der höchste 
Schalldruckpegel beträgt 70 dB (A) oder weniger gemäß EN ISO 7779.
Disclaimer
Kyocera Mita will not be liable to customers or any other person or entity 
for any loss or damage caused or alleged to be caused directly or indirectly 
by equipment sold or furnished by  us, including but not limited to, any 
interruption of service, loss of bu siness or anticipatory profits, or 
consequential damages resulting from the use or operation of the 
equipment or software.
Energy Star Program
As an ENERGY STAR Partner, we have determined that this product meets 
the ENERGY STAR guidelines for energy efficiency.
The basic objective of the ENERGY STAR Program is to reduce environmental 
pollution by encouraging the manufacture and sale of equipment that uses 
energy more efficiently.
This printer is equipped with a sleep  timer function that conforms with the 
standards of the E
NERGY STAR Program. This function makes it possible to 
reduce the amount of electrical power consumed by the printer. For 
maximum power savings, turn off the printer’s power supply when not 
using the printer for extended periods of time.
For details on the sleep timer functi on and printer power consumption, 
refer to this manual.
Initial settings of the sleep timer f unction and power saved using the sleep 
timer function:
 FS-9130DNFS-9530DN
Initial Auto Sleep 
Setting15 minutes (60 minutes)15 minutes (60 minutes)
Power 
Consumption in 
Auto Sleep4.5W (40W)4.5W (75W)
( ): ENERGY STAR program guideline
Downloaded From ManualsPrinter.com Manuals 
						

							
 
xviOPERATION GUIDE
Please read this Operation Guide before using the machine. Keep it close 
to the machine fo r easy reference.
The sections of this guide and parts  of the machine marked with symbols 
are safety warnings meant to protect the user, other individuals and 
surrounding objects, and ensure correct and safe usage of the machine. 
The symbols and their meanings are indicated below.
DANGER : Indicates that serious  injury or even death will 
very possibly result from insuff icient attention to or incorrect 
compliance with the related points. 
WARNING : Indicates that serious in jury or even death may 
result from insufficient attent ion to or incorrect compliance 
with the related points. 
CAUTION : Indicates that personal injury or mechanical 
damage may result from insuffic ient attention to or incorrect 
compliance with the related points. 
Downloaded From ManualsPrinter.com Manuals 
						

							
 
OPERATION GUIDExvii
Symbols
The following symbols indicate that the related section includes safety 
warnings. Specific points  of attention are indicated inside the symbol.
....[General warning]
....[Warning of danger of electrical shock]
....[Warning of high temperature]
The following symbols indicate that  the related section includes 
information on prohibited actions. Specifics of the prohibited action are 
indicated inside the symbol. 
....[Warning of prohibited action]
....[Disassembly prohibited]
The following symbols indicate that  the related section includes 
information on actions which must be  performed. Specifics of the required 
action are indicated inside the symbol. 
....[Alert of required action]
....[Remove the power plug from the outlet]
....[Always connect the machine to an outlet with a ground 
connection]
Please contact your service representa tive to order a replacement if the 
safety warnings in this Op eration Guide are illegible or  if the guide itself is 
missing. (fee required)
Downloaded From ManualsPrinter.com Manuals 
						

							
 
xviiiOPERATION GUIDE
Installation Precautions
Environment
 CAUTION:
Avoid placing the machine on or in locations which are unstable 
or not level. Such locations may cause the machine to fall down 
or fall over. This type of situation presents a danger of personal 
injury or damage to the machine. 
Avoid locations with humidity or  dust and dirt. If dust or dirt 
become attached to the power plug, clean the plug to avoid the 
danger of fire or electrical shock.
Avoid locations near radiators, heat ers, or other heat sources, or 
locations near flammable items,  to avoid the danger of fire.
To keep the machine cool and fa cilitate changing of parts and 
maintenance, allow access space as shown below. Leave 
adequate space, especially around the vents, to allow air to be 
properly ventilated out of the 
printer.
Left: 300 mm
(12 inches) Right: 300 mm
(12 inches) Rear: 100 mm
(4 inches) Front: 1,000 mm
(40 inches)
Always use the caster st oppers to stabilize the printer once it is 
in place to keep it from moving  and/or falling over and causing 
injury.
Other Precautions
Adverse environmental conditions may affect the safe operation and 
performance of the machine. Inst all in an air-conditioned room 
(recommended room temperature: around 23°C, humidity: around 60% 
RH), and avoid the following locations when selecting a site for the 
machine.
Downloaded From ManualsPrinter.com Manuals