Kyocera FS 3920DN User Manual

							
4-4Connecting and Printing
Changing Network Interface Parameters
This printer supports TCP/IP, TCP/IP (IPv6), NetWare, AppleTalk, IPP, 
SSL Server, IPSec protocols, and Security Level. For more information, 
refer to the  Advanced Operation Guide .
TCP/IP, TCP/IP (IPv6) settings
1
Press [MENU] .
2Press U or  V repeatedly until  Network > appears.
3Press Z. Each time you press  U or  V, the selection changes. Refer 
to the explanations below when specifying the settings.
Set this item to  On when you connect to a network using  TCP/IP. 
Submenu has items including  DHCP, IP Address , Subnet Mask , 
Gateway  and Bonjour .
Set this item to  On when you connect to a network using  TCP/IP 
(IPv6) . Submenu has items including  RA(Stateless)and 
DHCPv6 .
NoteAfter all network related settings have been done, turn the 
machine OFF and ON again. This is mandatory to make the 
settings effective.
Network        >
>TCP/IP
  Off
>TCP/IP (IPv6)
  Off
Downloaded From ManualsPrinter.com Manuals 
						

							
Connecting and Printing4-5
TCP/IP
This section describes how to enable the TCP/IP protocol. 
1If TCP/IP  is set to  Off, use  U or  V to select  On and press  [OK].
2Press  Z. Each time you press  U or  V, the selection changes.
3Display the item you want to set and press  [OK]. A blinking question 
mark ( ?) appears while you are setting  DHCP and Bonjour . A 
blinking cursor ( _) appears while you are setting  IP Address, 
Subnet Mask  and Gateway .
4Press U or  V to select  On or  Off  as the setting for  DHCP and 
Bonjour .
For the  IP Address , Subnet Mask  and Gateway  settings, press 
U  or  V to move the blinking cursor to the number you want to 
change ( 000 to 255 ). Use  Y and  Z to move the cursor right and left.
5Press  [OK].
6Press  [MENU] . The display returns to  Ready.
NoteCheck with your network administrator for the network 
address settings. 
>TCP/IP        >
  On
>>IP Address
 000.000.000.000
>>Subnet Mask
 000.000.000.000
>>Gateway
 000.000.000.000
>>DHCP
  Off
>>Bonjour
  Off
>>Subnet Mask
 0
00.000.000.000
Downloaded From ManualsPrinter.com Manuals 
						

							
4-6Connecting and Printing
TCP/IP (IPv6)
This section describes how to enable the TCP/IP (IPv6) protocol.
1If TCP/IP (IPv6)  is set to Off, use  U or  V to selecto  On and 
press   [OK].
2Press  Z. Each time you press  U or  V, the selection changes.
3Display the item you want to set and press  [OK]. A blinking question 
mark ( ?) appears while you are setting  RA(Stateless) and 
DHCPv6 .
4Press U or  V to select  On or  Off  as the setting for 
RA(Stateless)  and DHCPv6 .
5Press [OK].
6Press  [MENU] . The display returns to  Ready.
NetWare, AppleTalk, IPP,  SSL Server, IPSec and 
Security Level settings
1
Press  [MENU] .
2Press U or  V repeatedly until  Security > appears.
NoteCheck with your network administrator for the network 
address settings. 
>TCP/IP (IPv6) >
  On
>>DHCPv6
  Off
>>RA(Stateless)
  Off
>>DHCPv6
 ?Off
>>RA(Stateless)
 ?Off
Security       >
Downloaded From ManualsPrinter.com Manuals 
						

							
Connecting and Printing4-7
3Press Z. Each time you press  U or  V, the selection changes. Refer 
to the explanations below when specifying the settings.
If you are using  NetWare, AppleTalk , IPP , SSL Server  or 
IPSec  to connect to a network, you must enter an administrator ID 
and press  [OK]. The default setting is the numeric part of your 
printers model name. If you use FS-2020D, enter  2020.
If you are using  NetWare, AppleTalk , IPP , SSL Server  or 
IPSec  to connect to a network, you must enter an administrator 
password and press  [OK]. The default setting is the numeric part of 
your printers model name. If you use FS-2020D, enter  2020.
Set this item to  On when you connect to a network using  NetWare. 
In submenu, frame mode can be selected from  Auto, 802.3 , 
Ethernet-II , SNAP  and 802.2 .
AppleTalk  must be activated ( On) for networking with Macintosh 
computers.
Set this item to  On when you connect to a network using  IPP.
Set this item to  On when you connect to a network using  SSL 
Server . Submenu has items including  DES, 3DES , AES , IPP over 
SSL  and  HTTPS .
Set this item to  On when you connect to a network using  IPSec.
Continued on next page.
ID
_
Password
_
>NetWare       >
  On
>AppleTalk
  On
>IPP
  Off
>SSL Server
  Off
>IPSec
  Off
Downloaded From ManualsPrinter.com Manuals 
						

							
4-8Connecting and Printing
Set the Security Level  to High .
NetWare
This section explains the procedure for enabling NetWare.
1Enter the administrator ID and password. Then, if  NetWare is set to 
Off , use  U or  V to select  On and press  [OK].
2Press  Z.
3Press  [OK]. A blinking question mark ( ?) appears. Each time you 
press  U or  V, the selection changes.
4Display the item you want to set and press  [OK].
5Press  [MENU] . The display returns to  Ready.
>Security Level
 High
>NetWare       >
  On
>>Frame Type
  Auto
>>Frame Type
 ?802.3
>>Frame Type
 ?Ethernet-II
>>Frame Type
 ?802.2
>>Frame Type
 ?SNAP
>>Frame Type
 ?Auto
Downloaded From ManualsPrinter.com Manuals 
						

							
Connecting and Printing4-9
AppleTalk
This section explains the procedure for enabling AppleTalk. 
1Enter the administrator ID and password. Then, if AppleTalk is set 
to  Off , use  U or  V to select  On.
2Press  [OK]. A blinking question mark ( ?) appears.
3Press  [OK] again.
4Press  [MENU] . The display returns to  Ready.
IPP
This section explains the procedure for enabling IPP. 
1Enter the administrator ID and password. Then, if  IPP is set to  Off, 
use  U or  V to select  On.
2Press  [OK]. A blinking question mark ( ?) appears.
3Press  [OK] again.
4Press  [MENU] . The display returns to  Ready.
>AppleTalk
  On
>AppleTalk
 ?On
>IPP
  On
>IPP
 ?On
Downloaded From ManualsPrinter.com Manuals 
						

							
4-10Connecting and Printing
SSL Server
This section explains the procedure for enabling SSL Server.
1Enter the administrator ID and password. Then, if SSL Server is 
set to  Off, use  U or  V to select  On and press  [OK].
2Press  Z. Each time you press  U or  V, the selection changes.
3Display the item you want to set and press  [OK]. A blinking question 
mark ( ?) appears.
4Select  On or  Off  using  U or  V.
5Press  [OK].
6Press  [MENU] . The display returns to  Ready.
IPSec
This section explains the procedure for enabling IPSec.
1Enter the administrator ID and password. Then, if  IPSec is set to 
Off , use  U or  V to select  On.
2Press  [OK]. A blinking question mark ( ?) appears.
3Press  [OK] again.
4Press  [MENU] . The display returns to  Ready.
>SSL Server
  On
>>3DES
  Off
>>AES
  Off
>>IPP over SSL
  Off
>>HTTPS
  Off
>>DES
  Off
>>DES
 ?Off
>IPSec
  On
>IPSec
 ?On
Downloaded From ManualsPrinter.com Manuals 
						

							
Connecting and Printing4-11
Security Level
Security Level is primarily a menu used by service personnel for 
maintenance work. There is no need for customers to use this menu.
>Security Level
  High
Downloaded From ManualsPrinter.com Manuals 
						

							
4-12Connecting and Printing
Printing a Network Interface Status Page
You can print out a status page for the network interface. The network 
status page shows the network addresses, and other information under 
various network protocols about the network interface.
Adjust/Maintenance
Adjust/Maintenance is used to adjust the print quality and to carry out 
printer maintenance.
The options available in Adjust/Maintenance are as follows:
•Restart Printer
• Service
1Press  [MENU] .
2Press U or  V repeatedly until  Adjust/Maintenance >  appears.
3Press Z while  Adjust/Maintenance >  is displayed.
4Press U or  V repeatedly until  >Service > appears.
5Press Z.
6Press  U or  V repeatedly until  >>Print Network Status Page  
appears.
7Press  [OK]. A question mark ( ?) appears.
8Press  [OK]. Processing  appears and a status page is printed out.
9When printing ends, the display returns to  Ready.
IMPORTANTService is primarily a menu used by service 
personnel for maintenance work. There is no need for customers to 
use this menu.
Adjust/        >
Maintenance
>>Print Network
 Status Page ?
Downloaded From ManualsPrinter.com Manuals 
						

							
Connecting and Printing4-13
Installing the Printer Driver
According to the instructions of the Installation Guide, connect the PC to 
the printer and turn on them to install the printer driver. 
For more 
information on printer driver, refer to the  KX Driver User Guide in the CD-
ROM.
Installing the Printer Driver on Windows PC
This section explains how to install the printer driver in Windows Vista.
1Ensure the printer is plugged in and connected to the computers 
USB or Network port before installing software from the CD-ROM.
2Insert the CD-ROM (Product Library) into the CD-ROM drive. If 
AutoPlay  screen appears, click  Run Setup.exe. The Notice screen 
appears.
3Select  View License Agreement  to read the information and select 
Accept  to proceed.
4Click Install Software . Installation Method screen appears.
5Select Express Mode or Custom Mode as the installation method.
• Express Mode: If the printer is connected via USB or a network and 
is turned on, the installer detects the printer. Select Express Mode to 
perform a standard installation.
Note To install the printer driver, you must log on with 
administrator privilege.
Note If a Plug and Play window like that shown at left 
appears, click  Cancel. 
NoteIf the installation program fails to launch, use Windows 
Explorer to access the CD-ROM and select Setup.exe. 
Note In Windows XP, click  Install Software to start the 
Installation wizard. Click  Next to display the Installation 
Method screen.
Downloaded From ManualsPrinter.com Manuals