Kyocera FS 1350DN User Manual

7-24Using the Operation Panel
Cassette (1 to 3) Type (Setting the cassette paper 
type)
By setting a paper type (plain, recycled, etc.) for the paper cassette, you 
can automatically select the paper in the paper cassette according to the 
paper type you command on the printer driver. The default setting is 
plain paper for all paper cassettes.
If the PF-100 optional paper feeder is installed, use the same procedure 
to setting the cassette paper type.
For more information about paper types that you can...

Using the Operation Panel7-25
Type Adjust (Creating custom paper type)
The following describes the procedure used to set a user-defined paper 
type for the printer. Eight custom user settings may be registered. After 
having been set, any of these may be called up when setting the paper 
type for a paper source.
The paper weight and duplex path can be set (refer to Paper Weight 
(Setting the paper weight) on page7-25, and Duplex Path (Setting the 
duplex path) on page7-26) after selecting the paper type...

7-26Using the Operation Panel
4Press U or V to display the desired paper thickness. The display 
changes as shown below. For details of the default setting for each 
paper type, refer to Paper Specifications on page2-2.
Light
Normal 1
Normal 2
Normal 3
Heavy 1
Heavy 2
Heavy 3
Extra Heavy
5Press [OK].
6Press [MENU]. The display returns to Ready.
Duplex Path (Setting the duplex path)
1Display the custom paper type (refer to Type Adjust (Creating 
custom paper type) on page7-25) and press Z.
2Press U or V...

Using the Operation Panel7-27
Print Settings
These settings specify printing parameters such as the print quality used 
for printing (Normal or Fine), the gloss mode (Low or High), the number 
of copies, reduced printing and the page orientation. 
The options available in Print Quality are as follows:
•Paper Source (Selecting the paper feed source)
•Paper Feed Mode (Setting the paper feed source)
•Duplex (Duplex Printing)
•Override A4/LT (Overriding difference between A4 and Letter)
•Emulation (Setting...

7-28Using the Operation Panel
Paper Feed Mode (Setting the paper feed source)
This mode specifies how the paper should be fed, after the paper feed 
source and paper type has been chosen. If Auto is selected, the printer 
searches for a paper feed source that matches the paper size and type, 
and paper is delivered from that source. An error message is displayed if 
Fixed is selected, but a match is not found. The default setting is Auto. 
To change the settings, follow the steps described below. 
1Press...

Using the Operation Panel7-29
Duplex (Duplex printing)
Using the duplexer, you can automatically print on both sides of the 
paper. The duplexer is mounted underneath the printer.
Duplex printing is available for the following paper types:
PLAIN
PREPRINTED
BOND
RECYCLED
ROUGH
COLOR
PREPUNCHED
HIGH QUALITY
CUSTOM 1 (to 8)
Activating the duplexer is done by selecting either short edge or long 
edge binding mode.
Binding Modes
Binding refers to the manner in which printed pages of paper are joined 
together...

7-30Using the Operation Panel
4Press U or V to display the desired binding mode. The message 
display toggles through the following:
Off (default)
Short edge bind
Long edge bind
5Press [OK].
6Press [MENU]. The display returns to Ready.
Override A4/LT (Overriding difference between A4 
and Letter)
When the Override A4/LT is turned On using the operation panel, the 
printer ignores the difference between A4 and Letter paper sizes. 
Printing is performed without an error message even if the actual paper...

Using the Operation Panel7-31
Alternative Emulation for KPDL Emulation
KPDL is Kyocera’s implementation of the PostScript language. The 
KPDL (AUTO) emulation enables the printer to automatically change the 
emulation mode according to the data received when printing.
In addition to KPDL (AUTO) emulation, you can use the operation panel 
to set another emulation mode that is used very often. The default 
setting is PCL 6.
1Press [MENU]. 
2Press U or V repeatedly until >Emulation > appears on the 
message...

7-32Using the Operation Panel
Font Select (Selecting the default font)
You can select the default font for the current interface. The default font 
can be one of the internal fonts or a font that is downloaded to the printer 
memory or stored on CompactFlash (CF) card.
In this menu, you can also set the type and pitch for Courier and Letter 
Gothic; as well as to print a font list.
1Press Z while Print Settings > is displayed.
2Press U or V repeatedly until >Font Select > appears.
3To select an internal...

Using the Operation Panel7-33
5Press [OK]. A blinking question mark (?) appears.
6Select Regular or Dark using U or V.
7Press [OK].
8Press [MENU]. The display returns to Ready.
Changing the Default Font Size
You can change the size of the default font. If you selected a proportional 
font, the character size can also be changed.
1Press Z while Print Settings > is displayed.
2Press U or V repeatedly until >Font Select > appears.
3Make sure that Internal is displayed and press Z.
4Press U or V repeatedly...