Konica Minolta magicolor 2550DN User Manual

Media Types 57 Letterhead
Try printing your data on a sheet of plain paper first to check placement. 
Postcards
Try printing your data on a sheet of plain paper first to check placement.Capacity Tray 1
Up to 50 sheets, depending on their size and 
thickness
Tra y 2
Not supported
Orientation
Face up
Driver 
Media TypeLetterhead
Weight
60 to 90 g/m² (16 to 24 lb bond)
Duplexing
See page 52 for supported sizes (face up—top of page first).
Capacity Tray 1
  Up to 50 postcards, depending on their 
thickness...

Media Types 58
Use postcards that are
#Approved for laser printers
DO NOT use postcards that are
#Coated
#Designed for inkjet printers
#Precut or perforated
#Preprinted or multicolored
!If the postcard is warped, press on the warped 
area before putting it in Tray 1.
#Folded or wrinkled
Transparencies
!Do not fan transparencies before loading them. Resulting static elec-
tricity may cause printing errors.
!If you touch the face of the transparencies with your bare hands, print 
quality may be affected....

Media Types 59
!If you have problems feeding 50 sheets, try loading only 1–10 sheets 
at a time. Loading a large number of transparencies at one time may 
cause static buildup, causing feeding problems.
!Always first test a small quantity of a particular type of transparency.
Use transparencies that are
#Approved for laser printing
DO NOT use transparencies that
#Have static electricity that will cause them to stick together
#Are specified for inkjet printers only
Glossy Stock
Test all glossy stock to...

Media Types 60
What Is the Guaranteed Imageable (Printable) Area?
The printable area on all media sizes is 
up to 4 mm (0.157) from the edges of 
the media.
Each media size has a specific image-
able area, the maximum area on which 
the printer can print clearly and without 
distortion. 
This area is subject to both hardware 
limits (the physical media size and the 
margins required by the printer) and 
software constraints (the amount of 
memory available for the full-page frame buffer). The guaranteed...

Loading Media 61
Loading Media 
How do I load media?
Take off the top and bottom sheets of a 
ream of paper. Holding a stack of approx-
imately 200 sheets at a time, fan the 
stack to prevent static buildup before 
inserting it in a tray.
!Do not fan transparencies.
Note
Although this printer was designed for printing on a wide range of 
media types, it is not intended to print exclusively on a single media 
type except plain paper. Continuous printing on media other than plain 
paper (such as envelopes,...

Loading Media 62
2Slide the media guides to pro-
vide more space between them.
3Load the paper face up in the 
tray.
!Do not load paper above 
the 
 mark. Up to 200 
sheets (80 g/m2 [22 lb]) of 
plain paper can be 
loaded into the tray at 
one time.
Downloaded From ManualsPrinter.com Manuals 

Loading Media 63
4Slide the media guides against 
the edges of the paper.
5Close the front panel of Tray 1 
tray, and then reattach the lid.
Other Media
When loading media other than plain paper, set the media mode (for exam-
ple, Envelope, Glossy, Label, Thick Stock or Transparency) in the driver for 
optimum print quality.
Downloaded From ManualsPrinter.com Manuals 

Loading Media 64
Loading Envelopes
1Remove the lid from Tray 1, and 
then open the front panel of 
Tray 1.
2Remove any media from the tray.
3Slide the media guides to pro-
vide more space between them.
4Load the envelopes flap side 
down in the tray. 
!Before loading enve-
lopes, press them down 
to make sure that all air is 
removed, and make sure 
that the folds of the flaps 
are firmly pressed; other-
wise the envelopes may 
become wrinkled or a 
media misfeed may 
occur.
!Up to 10 envelopes can be...

Loading Media 65
!For envelopes with the 
flap along the long edge, 
load the envelopes with 
the flap toward the left of 
the printer.
5Slide the media guides against 
the edges of the envelopes.
6Close the front panel of Tray 1 
tray, and then reattach the lid.
Downloaded From ManualsPrinter.com Manuals 

Loading Media 66
7Pull the lever, and then open the 
top cover.
!If there is paper in the 
output tray, remove it. 
Fold up the output tray 
before opening the top 
cover.
!Do not touch the transfer 
belt.
8Raise the fuser separator levers 
on the fuser unit.
Downloaded From ManualsPrinter.com Manuals