Konica Minolta magicolor 1690MF User Manual

Loading Media 3-20
3Remove the lid from Tray 2.
4Press down the media pressure 
plate to lock it into place.
5Load the paper face up in the 
tray.
Do not load above the 
100% line. Up to 500 
sheets (80 g/m
2 [21 lb]) of 
plain paper can be 
loaded into the tray at 
one time.100%
75
50
Downloaded From ManualsPrinter.com Manuals 

Loading Media3-21
6Reattach the lid to Tray 2.
7Reinsert Tray 2 into the 
machine.
Downloaded From ManualsPrinter.com Manuals 

About Duplex Printing 3-22
About Duplex Printing
Duplex (double-sided) printing can be performed when the duplex option has 
been installed on this machine.
For details on installing the duplex option, refer to “Duplex Option” on 
page 10-7.
If the paper has low opacity (high translucency), then the printed data from 
one side of the page will show through to the other side. Check your applica-
tion for margin information. For best results, print a small quantity to make 
sure the opacity is...

About Duplex Printing3-23
In addition, if “Combination” has been set to “Booklet”, autoduplex printing is 
performed.
The following Order settings are available when “Booklet” is selected.
1Load plain paper into the tray.
2From the printer driver, specify duplex (double-sided) printing (Layout tab 
in Windows).
3Click OK.
With autoduplexing, the back side is printed first, and then the front 
side is printed.If “Left Binding” is selected, the pages can be folded as a 
left-bound booklet.
If “Right...

Output Tray 3-24
Output Tray
The printed media is fed out facing down into the output tray below the control 
panel. This tray has a capacity of approximately 100 sheets (A4/Letter) of 80 
g/m
2 paper.
If the media is stacked too high in the output tray, your machine may 
experience media misfeeds, excessive media curl, or static buildup. 
The output tray can be pulled out to 
be extended. Adjust the output tray 
according to the size of paper to be 
printed on.
Downloaded From ManualsPrinter.com Manuals 

Media Storage3-25
Media Storage
„Keep media on a flat, level surface in its original wrapper until it is time to
load it.
Media that has been stored for a long time out of its packaging may dry up 
too much and cause misfeeding.
„If media has been removed from its wrapper, place it in its original pack-
aging and store in a cool, dark place on a level surface.
„Avoid moisture, excessive humidity, direct sunlight, excessive heat (above 
35°C [95°F]), and dust 
„Avoid leaning against other objects or...

Original Media 3-26
Original Media
Specifications
Documents that can be placed on the original glass
The following types of documents can be placed on the original glass.
Observe the following precautions when placing a document on the original 
glass.
„Do not place objects weighing more than 3 kg (6.6 lb) on the original 
glass; otherwise the glass may be damaged.
„Do not press down extremely hard on a book spread on the original glass; 
otherwise the original glass may be damaged.
Documents that can be...

Original Media3-27
„Documents with pages that have had cutouts removed or are cutouts
„Label sheets
„Offset printing masters
„Documents with binder holes
Downloaded From ManualsPrinter.com Manuals 

Loading a Document to be Copied 3-28
Loading a Document to be Copied
Placing a document on the original glass
1Lift to open the ADF cover.
2Position the document on the 
original glass.
Align the document with 
the arrow on the left side 
toward the rear of the 
machine.
Document
Downloaded From ManualsPrinter.com Manuals 

Loading a Document to be Copied3-29
3Gently close the ADF cover.
Loading a document into the ADF
1Put the document into the ADF 
document feed tray face up.
Before loading a docu-
ment into the ADF, check 
that no document pages 
remain on the original 
glass.
Load the document 
pages so that the top of 
the document is toward 
the back or the right side 
of the machine.
2Adjust the document guides to 
the document size.
For details on copying the loaded document, refer to “Using the 
Copier” on page...