Konica Minolta magicolor 1650EN User Manual

Status, Error, and Service Messages 8-34
Error Messages (Operator Call)
This 
message...means... do this...
AUTH
TIMEOUTThe user is automatically 
logged off due to IEEE802.1x 
port authorization.Reauthorize the IEEE802.1x 
port, and then log on.
AIDC 
ERRORAIDC sensor error. Open and close front cover 
to automatically clean AIDC 
parts.
BELT 
ERRORThe printer detected incorrect 
image position on the image 
transfer belt.Check the cyan and black 
toner cartridges and replace 
them if they have run...

Status, Error, and Service Messages8-35
PUT
SIZE
TYPE
IN TRAY 1The size of paper being 
printed on is different from the 
size of paper specified in the 
printer driver.Load the correct paper on 
Tray1, and press the Menu 
Select key, then specify the 
size and type of the paper.
PUT 
“SIZE” 
“TYPE”
IN TRAY 2The paper size set from the 
printer driver is different from 
the size of paper loaded into 
Tray 2. „Open Tray 2 and keep 
correct paper size. Then 
close Tray 2.
„Specify the correct paper 
size...

Status, Error, and Service Messages 8-36
Service Messages
These messages indicate a more serious error that can only be corrected by 
a customer service engineer. If one of these messages appears, turn the 
printer off, then turn it on again. If the problem persists, contact your local 
vendor or authorized service provider.  
This service 
message...means... do this...
SERVICE 
CALL XXXXAn error has been detected 
with the item indicated “XXXX” 
in the service message.Reboot the printer. This often...

Installing
Accessories
Downloaded From ManualsPrinter.com Manuals 

Introduction 9-2
Introduction
Note
Use of accessories not manufactured or supported by 
KONICA MINOLTA will void your warranty. 
This chapter provides information about the following accessories.
Note
Installing accessories always requires that the printer and accessories 
are turned off and unplugged during installation.
For details on the available options, refer to 
printer.konicaminolta.com. Tray 2500-sheet tray
Duplex OptionAuto duplexing
In order for the duplex option to be installed, 
Tray 2...

Tray 29-3
Tray 2
If Tray 2 is installed, up to 500 additional sheets of A4/Letter-size paper can 
be loaded.
Installing Tray 2
Note
Since consumables are installed in the printer, be sure to keep the 
printer level when moving it in order to prevent accidental spills.
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
Downloaded From ManualsPrinter.com Manuals 

Tray 2 9-4
2Remove the dust cover from Tray 1.
Close Tray 1 and the output tray.
3Prepare Tray 2.
Be sure to place Tray 2 on a level surface.
4Lift the printer and place it on top 
of Tray 2, making sure that the 
positioning pins on Tray 2 cor-
rectly fit into the holes in the bot-
tom of the printer.
5Open Tray 1 and reattach the dust cover.
6Load paper into Tray 2.
For details on loading paper, refer to “Tray 2” in “Loading Plain Paper” on 
page 5-18.
7Insert Tray 2 into the printer.
8Reconnect all...

Tray 29-5
9Reconnect the power cord, and 
turn on the printer.
10Declare the Tray 2 in the Windows printer driver (Properties/Configure 
tab, see page 2-2).
Downloaded From ManualsPrinter.com Manuals 

Duplex Option 9-6
Duplex Option
Duplex (Double Sided) printing can be performed automatically with the 
duplex option installed. 
See “Duplexing” on page 5-21.
In order for the duplex option to be installed, either of the following must be 
installed on the printer.
zTray 2
zAttachment
If Tray 2 is installed, it is not necessary to install the attachment. In this 
case, skip “Installing the Attachment”, and continue with “Installing the 
Duplex Option” on page 9-8.
Installing Attachment
If the...

Duplex Option9-7
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Remove the dust cover from 
Tray 1.
Close Tray 1 and the output tray.
3Prepare the attachment.
Be sure to place the attachment on a level surface.
4Lift the printer and place it on top 
the attachment, making sure that 
the positioning pins on the 
attachment correctly fit into the 
holes on the bottom of the 
printer.
5Open Tray 1 and reattach the dust cover.
Next, install the duplex option.
Downloaded From...