Konica Minolta magicolor 1650EN User Manual

Replacing Consumables 6-10
Note
Do not touch the contact 
indicated in the illustration.
9Press in the toner cartridge until 
it locks into place.
10Close the front cover.
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables6-11
The printer must complete a calibration cycle after the toner car-
tridge has been replaced. If you open the top or front cover before 
the message 
IDLE appears, the printer stops and repeats the cal-
ibration cycle.
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables 6-12
Removing All Toner Cartridges
Note
Be careful not to spill toner while removing a toner cartridge. If toner 
spills, immediately wipe it off with a soft, dry cloth.
By using the REMOVE ALL mode, all toner cartridges can be removed.
Follow the procedure described below to use the REMOVE ALL mode.
1Perform the operation described below to switch the printer to the 
REMOVE ALL mode.
Press Key Until Display Reads
IDLE
MANU
MAIN MANU
MAIN MENU
PRINT MENU
 × 2MAIN MENU
QUALITY MENU...

Replacing Consumables6-13
It is not possible to exit REMOVE ALL mode before the operation is 
finished (even if the Cancel key is pressed).
If the printer has incorrectly been switched to REMOVE ALL mode, 
open, then close the front cover four times to exit REMOVE ALL 
mode.
2Open the front cover.
Before opening the front 
cover, open Tray 1 if it is 
not already open.
REMOVE ALL
*NO
 REMOVE ALL
YES
*YES 
IS SELECTED
Then, it displays
OPEN DOOR AND
REMOVE M TONER
Press Key Until Display Reads...

Replacing Consumables 6-14
3Pull down the handle on the 
toner cartridge until the toner 
cartridge is unlocked and moves 
out slightly toward you.
Remove the toner cartridge.
Do not manually rotate 
the toner cartridge carou-
sel. In addition, do not 
rotate the carousel with 
force, otherwise it may be 
damaged.
Note
Do not touch the contact 
indicated in the illustration.
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables6-15
4Close the front cover.
5Follow the same procedure to remove the cartridges for the cyan, black, 
then yellow toners.
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables 6-16
Replacing the Imaging Cartridge
When replacing an imaging cartridge, refer to the following table. For opti-
mum print quality and performance, use only approved KONICA MINOLTA 
imaging cartridge for your specific printer type, as listed in the table below. 
You can find your machine type and the imaging cartridge part numbers on 
the consumables reorder label  inside the top cover your machine.
For optimum print quality and performance, use only the corre-
sponded TYPE...

Replacing Consumables6-17
Note
Dispose of the used imaging cartridge according to your local 
regulations. Do not burn the imaging cartridge.
3Prepare the new imaging cartridge.
Note
Do not touch the PC drum and the transfer belt on the imaging 
cartridge.
4Slowly insert the new imaging 
cartridge vertically, and then 
push it slightly down toward you 
to finish installing the imaging 
cartridge.
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables 6-18
5Carefully close the top cover.
The printer must complete a calibration cycle after the imaging car-
tridge has been replaced. If you open the top cover before the 
message 
IDLE appears, the printer stops and repeats the calibra-
tion cycle.
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables6-19 Replacing the Fuser Unit
For optimum print quality and performance, use only approved KONICA 
MINOLTA fuser unit for your specific printer type.
1Turn off the printer and discon-
nect the power cord.
Note
There are extremely hot parts within the printer. Before replacing the 
fuser unit, wait about 20 minutes after turning off the printer, and 
then check that the fusing section has reached room temperature, 
otherwise, you may get burnt.
2Open the top cover.
If there is paper...