Konica Minolta magicolor 1600W User Manual

Indicator Messages 7-8
* Differs depending on the toner status.
OffSlow 
blinking *Memory fullPress the Clear 
key.
If the error is not 
corrected, turn off 
the printer. After a 
few seconds, turn 
on the printer.
OffBlinking*Front cover or top 
cover is open. Close the front 
cover and top 
cover.
*The imaging cartridge 
is not installed. Install the imaging 
cartridge. 
OffRapid 
blinking *Media jam Clear the jam, 
close the covers, 
and then continue 
with the print job. 
OffRapid 
blinkingAll...

Indicator Messages7-9
Service Message
This message indicates a more serious fault that can only be corrected by a 
customer service engineer.
Ready 
indicator 
(green)Error 
indicator 
(orange)To n e r  
indicator 
(orange)ConditionAction
Rapid 
blinkingRapid 
blinkingAll blinkingFatal errorTurn off the 
printer. After a 
few seconds, 
turn on the 
printer. 
If the problem 
persists, con
-
tact your ven-
dor or 
authorized ser
-
vice provider.
Downloaded From ManualsPrinter.com Manuals 

Clearing Media Misfeeds 7-10
Clearing Media Misfeeds 
To avoid damage, always remove misfed media gently, without tearing it. Any 
pieces of media left in the printer, whether large or small, can obstruct the 
media path and cause further misfeeds. Do not reload media that has misfed.
Note
The image is not fixed on the media before the fusing process. If you 
touch the printed surface, the toner may stick to your hands, so be 
careful not to touch the print face when removing the misfed media. 
Make sure...

Clearing Media Misfeeds7-11
Clearing Procedures
1Open the top cover.
If there is paper in the 
output tray, remove it, 
and then fold up the out
-
put tray before opening 
the top cover.
2Grab the handle and lift it up 
slightly to the back, and then 
slowly pull the imaging cartridge 
out vertically.
Downloaded From ManualsPrinter.com Manuals 

Clearing Media Misfeeds 7-12
Note
Do not touch the PC drum on the imaging cartridge.
Position the removed imaging 
cartridge horizontally as shows in 
the illustration at the right.
 
Be sure to keep the imaging 
cartridge horizontal and place it 
where it will not become dirty.
 
Do not leave the imaging 
cartridge removed for more than 
15 minutes, and do not place the 
removed imaging cartridge in a 
location where it would be 
exposed to direct light (such as 
sunlight).
Downloaded From...

Clearing Media Misfeeds7-13
3Push the fuser separator levers 
back as far as possible.
CAUTION
The area around the fuser unit is 
extremely hot.
 
Touching anything other than the 
indicated levers may result in 
burns. If you get burned, 
immediately cool the skin under 
cold water, and then seek 
professional medical attention.
 
 
 
 
 
 
M
Downloaded From ManualsPrinter.com Manuals 

Clearing Media Misfeeds 7-14
4Remove any misfed media.
Raise the fuser unit cover 
and remove the media.
M
M
Downloaded From ManualsPrinter.com Manuals 

Clearing Media Misfeeds7-15
Note
Do not touch the paper exit 
sensor on the fuser unit. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Note
Decreased print quality may 
result if the surface of the 
transfer roller is touched.
 
Be careful not to touch the 
surface of the transfer roller.
 
 
 
 
 
 
 
 
 
 
 
 
 
 
M
BOTTOM
VIEW
Downloaded From ManualsPrinter.com Manuals 

Clearing Media Misfeeds 7-16
5Return the fuser separator 
levers to their original positions.
6Slowly insert the imaging car-
tridge vertically, and then push it 
slightly down toward you to fin
-
ish reinstalling the imaging car-
tridge.
M
Downloaded From ManualsPrinter.com Manuals 

Clearing Media Misfeeds7-17
7Carefully close the top cover.
Downloaded From ManualsPrinter.com Manuals