Konica Minolta bizhub C552 User Manual

bizhub C652/C652DS/C552/C552DS/C4529-10
9.2 Troubleshooting table9
Icons that appear in the touch-panel screen
Now Downloading Program 
Data from the Firmware server.(1) CS Remote Care was activat-
ed by your service representa-
tive.
(2) Internet ISW is being down-
loaded.Do not turn off the sub power 
switch while this message is dis-
played.
After turning off the sub power 
switch, turn off the main power 
switch, and then contact your 
service representative.
Authentication information en-
tered is...

bizhub C652/C652DS/C552/C552DS/C4529-11
9.2 Troubleshooting table9
Indicates that Enhanced Security Mode is set to ON.
Appears when the external memory (USB memory) is not connected.
Indicates that a nonstandard external memory has been connected to this 
machine, therefore, USB connection is not enabled.
Indicates that the job is in the waiting-for-redial status because, for exam-
ple, the recipients line is busy when sending with the G3 Fax or IP Address 
Fax function. Icon Description
Downloaded From...

bizhub C652/C652DS/C552/C552DS/C4529-12
9.3 If print quality is deteriorated9
9.3 If print quality is deteriorated
Cleaning the electrostatic charger wire
If the electrostatic charger wire is dirty, streaks will appear though the printed images. If this occurs, follow 
the procedure described below to clean the electrostatic charger wire.
0When replacing the waste toner box, follow the Quick Guide to clean the electrostatic charger wire.
1Open the machines lower front door.
2Slowly pull out the...

bizhub C652/C652DS/C552/C552DS/C4529-13
9.3 If print quality is deteriorated9
Cleaning the print head
If the print head becomes dirty, print quality may be reduced. If this occurs, clean the print head according 
to the following procedure.
1Pull out tray 1.
2Remove the print head glass cleaning tool from tray 1.
3Open the machines lower front door.
4Release the securing levers for the waste toner box, and then 
remove the waste toner box.
Downloaded From ManualsPrinter.com Manuals 

bizhub C652/C652DS/C552/C552DS/C4529-14
9.3 If print quality is deteriorated9
5Insert the print head glass cleaning tool into the print head 
cleaning opening, pull it out, and then repeat this back-and-forth 
movement two or three times.
6Install the waste toner box.
7Place back the print head glass cleaning tool to tray 1.
8Close tray 1.
Downloaded From ManualsPrinter.com Manuals 

10Authentication unit (biometric 
type)
Downloaded From ManualsPrinter.com Manuals 

bizhub C652/C652DS/C552/C552DS/C45210-2
10.1 Using an authentication unit (biometric type)10
10 Authentication unit (biometric type)
This chapter describes the authentication unit (biometric type).
1. Authentication unit (biometric type) AU-101
2. Authentication unit (biometric type) AU-102
10.1 Using an authentication unit (biometric type)
The authentication unit (biometric type) is a biometrics (biometric authentication) system that scans a finger 
vein pattern to perform personal authentication. Using...

bizhub C652/C652DS/C552/C552DS/C45210-3
10.1 Using an authentication unit (biometric type)10
To use the authentication unit, first register the finger vein pattern of the user in this machine. The registered 
user, who is authenticated with the finger vein pattern, can log in to this machine or execute a print job. This 
section explains how to configure the required settings in this machine, register users, and log in with 
authentication.
10.1.1 Configuring this machine
NOTICE
User authentication...

bizhub C652/C652DS/C552/C552DS/C45210-4
10.1 Using an authentication unit (biometric type)10
7Configure Beep Sound and Operation Settings.
%For Beep Sound, specify whether to give a blip sound when the finger vein pattern is scanned 
successfully.
%For Operation Settings, specify how to log in to this machine after registration.
1-to-many authentication: Allows the user to log in by simply placing his or her finger.
1-to-1 authentication: Allows the user to log in by entering the user name and placing...

bizhub C652/C652DS/C552/C552DS/C45210-5
10.1 Using an authentication unit (biometric type)10
10.1.2 Registering a user
The following two methods can be used to register a user.
-Connect the authentication unit to this machine, and directly register the target user in this machine
-Connect the authentication unit to your computer, and use Data Administrator to register the target user
NOTICE
The registered user data is saved in the HDD of this machine. Changing the user authentication type of this...