Konica Minolta bizhub 600 User Manual

							2Before Making Copies
2-22 bizhub 750/600
Before Making Copies
Chapter 2
2.2 Adjusting the Angle of the Control Panel
The control panel can be adjusted to either of two angles.
Adjust the control panel to the angle that allows for easy operation.
To adjust the angle of the control panel
1Press the control panel 
release lever, and then 
push down on the con-
trol panel.
Downloaded From ManualsPrinter.com Manuals 
						

							Before Making Copies2
bizhub 750/600 2-23
Before Making Copies
Chapter 2
The control panel stops 
at the lower position.
2To return the control 
panel to the upper posi-
tion, press the control 
panel release lever, and 
then pull up on the con-
trol panel.
2
Note 
The control panel can also be grabbed anywhere on its outer edge and 
lifted.
Downloaded From ManualsPrinter.com Manuals 
						

							2Before Making Copies
2-24 bizhub 750/600
Before Making Copies
Chapter 2
2.3 Turning on the Main Power and the Sub Power
This machine has two power controls: the main power switch and the sub 
power switch.
To turn on the machine
The main power switch turns on/off all functions of the machine. Normally, 
the main power switch is turned on.
The sub power switch turns on/off machine operations, for example, for cop-
ying, printing or scanning. When the sub power switch is turned off, the ma-
chine enters a state where it conserves energy.
1Open the front door on the left side.
The main power switch 
is on the left side inside 
the machine.
2Turn on the main power switch.
The indicator on the 
main power switch lights 
up in green.
Downloaded From ManualsPrinter.com Manuals 
						

							Before Making Copies2
bizhub 750/600 2-25
Before Making Copies
Chapter 2
3Turn on the sub power 
switch.
!
Detail 
When the control panel is turned on by using the sub power switch, the 
indicator on the [Start] key lights up in orange, and a screen indicating 
that the machine is starting up appears.
After a few seconds, the message “Now warming up. Ready to scan.” ap-
pears on the touch panel, and the indicator on the [Start] key lights up in 
green, indicating that a job can now be queued.
!
Detail 
The default settings are those that are selected immediately after the ma-
chine is turned on (the power switch is set to “I”) and before any setting 
is specified from the control panel or touch panel, and those that are se-
lected when the [Reset] key is pressed to cancel all settings specified 
from the control panel or touch panel. The default settings can be 
changed. For more details, refer to “Initial Setting” on page 12-24.
The factory default settings are the settings that were selected when this 
machine was sent from the factory.
2
Note 
A job can also be queued while the machine is warming up after the sub 
power switch is turned on. For details, refer to “To scan during warm-up” 
on page 2-26.
Downloaded From ManualsPrinter.com Manuals 
						

							2Before Making Copies
2-26 bizhub 750/600
Before Making Copies
Chapter 2
To scan during warm-up
1Turn on the sub power switch.
The indicator on the [Start] key lights up in orange.
?How is the machine turned on?
%For details on turning on the machine, refer to “To turn on the ma-
chine” on page 2-24.
2Check that the message “Now warming up. Ready to scan.” appears 
on the touch panel.
– After the warm-up message is displayed, the Basic screen appears.
The indicator on the [Start] key lights up in green.
3Position the original to be copied.
?How is the original positioned?
%For details on positioning the original to be copied, refer to “Posi-
tioning the Original” on page 3-7.
4Using the keypad, specify the desired number of copies.
?How is the number of copies specified?
%For details on specifying the number of copies, refer to “General 
Copy Operation” on page 3-2.
Downloaded From ManualsPrinter.com Manuals 
						

							Before Making Copies2
bizhub 750/600 2-27
Before Making Copies
Chapter 2
5Specify any necessary copy settings.
6Press the [Start] key.
The original is scanned, and the job is added to the list of queued jobs.
7Check that the original has finished being scanned, and then position 
the next original.
8Specify new copy settings and the desired number of copies, and then 
press the [Start] key. 
– After the machine has finished warming up, the jobs will automati-
cally be printed in the order that they were queued.
?How is the printing of a job stopped?
%Press the [Stop] key. For details, refer to “Stopping Scanning/Print-
ing” on page 3-86.
!
Detail 
While the machine is warming up to begin printing after it is turned on us-
ing the sub power switch, copy settings can be specified and an original 
can be scanned to reserve a copy job. 
After the machine has finished warming up, the scanned image will be 
printed.
The machine takes about 5 minutes (bizhub 750)/4 minutes 30 seconds 
(bizhub 600) to warm up at normal room temperature (68°F) when the 
control panel is turned on using the sub power switch after the machine 
is turned on using the main power switch.
The output order can be changed or jobs can be deleted from the Current 
Jobs list of the Job List screen. For details, refer to “Managing Jobs (Job 
List)” on page 11-2.
Downloaded From ManualsPrinter.com Manuals 
						

							2Before Making Copies
2-28 bizhub 750/600
Before Making Copies
Chapter 2
To turn off the machine
1Turn off the sub power 
switch.
The touch panel goes 
off.
The main power indica-
tor lights up in green.
2Turn off the main power 
switch.
2
Reminder 
Do not turn off the machine with the main power switch or the sub power 
switch while it is making copies or printing, otherwise a paper misfeed 
may occur.
Do not turn off the machine with the main power switch or the sub power 
switch while it is scanning or sending or receiving data, otherwise all 
scanned data or transmission data will be deleted.
Do not turn off the machine with the main power switch while a queued 
job or stored data is waiting to be printed, otherwise the jobs will be 
deleted.
Downloaded From ManualsPrinter.com Manuals 
						

							Before Making Copies2
bizhub 750/600 2-29
Before Making Copies
Chapter 2
!
Detail 
The following are cleared when the main power switch and sub power 
switch are turned off.
Settings that have not been programmed
Jobs queued to be printed
When turning the main power switch off then on, be sure to wait 10 sec-
onds or longer before turning it on again;
otherwise the machine may not operate properly.
Automatically Canceling the Settings (Automatic Panel Reset)
If the [Reset] key is not pressed and no operation is performed for a specified 
length of time, settings that have not been programmed, such as the number 
of copies, are cleared and return to their default settings.
This is the automatic panel reset operation.
As the factory default, the automatic panel reset operation is performed after 
1 minute.
!
Detail 
The length of time until the automatic panel reset operation is performed 
and whether or not it is performed can be set from the Administrator 
mode. For details, refer to “System Setting” on page 12-19.
Automatically Canceling the Mode Screen (Automatic System Reset)
If no operation is performed for a specified length of time, the screen is au-
tomatically changed to that for the mode given priority.
This is the automatic system reset operation.
As the factory default, the Copy mode screen is displayed after 1 minute.
!
Detail 
The mode screen that is displayed when the automatic system reset op-
eration is performed can be changed from the Administrator mode. For 
details, refer to “System Setting” on page 12-19.
Downloaded From ManualsPrinter.com Manuals 
						

							2Before Making Copies
2-30 bizhub 750/600
Before Making Copies
Chapter 2
Automatically Conserving Energy (Low Power Mode)
If no operation is performed for a specified length of time, the touch panel 
goes off and the machine automatically enters a mode where it conserves 
energy.
This is the Low Power mode.
The machine can receive jobs even while it is in Low Power mode.
As the factory default, the machine enters Low Power mode after 15 minutes.
To recover from Low Power mode
1Press the [Power Save] key.
2The machine can receive jobs while it is warming up.
– The touch panel comes on again and, after the machine has fin-
ished warming up, it is ready to begin printing.
2
Note 
As the factory default, pressing the [Power Save] key causes the machine 
to enter Low Power mode. Settings in the Administrator mode can be 
changed to put the machine in Sleep mode instead. For details, refer to 
“System Setting” on page 12-31.
The Low Power mode can also be canceled by pressing any key in the 
control panel or by touching the touch panel.
!
Detail 
The length of time until the machine enters Low Power mode can be 
changed. For details, refer to “System Setting” on page 12-19, 
page 12-31.
If the time for entering Low Power mode and Sleep mode are the same, 
the machine will immediately enter Sleep mode without entering Low 
Power mode.
Downloaded From ManualsPrinter.com Manuals 
						

							Before Making Copies2
bizhub 750/600 2-31
Before Making Copies
Chapter 2
Automatically Conserving Energy (Sleep Mode)
If no operation is performed for a specified length of time, the machine auto-
matically enters a mode where it conserves energy.
Although the machine conserves more energy in Sleep mode than in Low 
Power mode, the machine must warm up when Sleep mode is canceled to 
begin printing again, therefore taking more preparation time than Low Power 
mode.
As the factory default, the machine enters Sleep mode after 60 minutes.
To recover from Sleep mode
1Press the [Power Save] key.
2The machine can receive jobs while it is warming up.
– The touch panel comes on again and, after the machine has fin-
ished warming up, it is ready to begin printing.
2
Note 
The Sleep mode can also be canceled by pressing any key in the control 
panel or by touching the touch panel.
!
Detail 
As the factory default, a machine with optional equipment installed enters 
Low Power mode if no operation is performed for 15 minutes, and then 
the machine enters Sleep mode after 60 minutes have elapsed.
The length of time until the machine enters Sleep mode can be changed. 
For details, refer to “System Setting” on page 12-31.
Downloaded From ManualsPrinter.com Manuals