Konica Minolta bizhub 600 User Manual

							2Before Making Copies
2-2 bizhub 750/600
Before Making Copies
Chapter 2
2 Before Making Copies
2.1 Part Names and Their Functions
Outside of Machine
12 3
5
6
7 8 9
13 104
11 12
14
Downloaded From ManualsPrinter.com Manuals 
						

							Before Making Copies2
bizhub 750/600 2-3
Before Making Copies
Chapter 2
2
Note 
The maximum angle that the ADF is opened can be adjusted in two stag-
es. For details, contact your technical representative.
No.Part NameDescription
1 ADF (automatic document feeder) Automatically feeds one original sheet at a time for 
scanning. If the double-sided original setting is se-
lected in the touch panel, the original is automatical-
ly turned over so that both sides can be scanned.
Referred to as the “ADF” throughout the manual. 
2 Toner cartridge door Opened when replacing the toner cartridge (See 
p. 9-4.) 
3 Working table Provides an area to temporarily place original and 
other materials
4 Sub  power  switch Use to turn on/off machine operations, for example, 
for copying, printing or scanning. When turned off, 
the machine enters a state where it conserves ener-
gy.
5 Multiple bypass tray Used when printing onto paper with a size not load-
ed into a paper tray or onto overhead projector 
transparencies or trace paper 
Holds up to 100 sheets of plain paper and 1 sheet 
of overhead projector transparencies or trace pa-
per.
Referred to as the “bypass tray” throughout the 
manual. (See p. 2-46)
6 Right-side door of the paper tray Opened when clearing paper misfeeds
7 Tray  4 Can be loaded with up to 500 sheets of paper (20lb), 
and can be set to different paper sizes (See p. 2-43.)
8 Tray  3 Can be loaded with up to 500 sheets of paper (20lb), 
and can be set to different paper sizes (See p. 2-43.)
9 Tray 2 Can be loaded with up to 1,000 sheets of paper 
(20lb) (See p. 2-41.)
10 Tray 1 Can be loaded with up to 1,500 sheets of paper 
(20lb) (See p. 2-41.)
11 Touch panel Displays various screens and messages.
12 Control panel Used to specify the various machine settings (See 
p. 2-15.)
13 Front doors (left and right) Opened when clearing paper misfeeds
14 Exit tray Collects printed pages
Downloaded From ManualsPrinter.com Manuals 
						

							2Before Making Copies
2-4 bizhub 750/600
Before Making Copies
Chapter 2
15
1617
No.Part NameDescription
15 Power cord Supplies power to the machine
16 Serial port (RS-232C) Used for transmissions with CS Remote Care
17 Network connector (10Base-T/
100Base-TX)Used for connecting the network cable when this 
machine is used for network printing and network 
scanning
Downloaded From ManualsPrinter.com Manuals 
						

							Before Making Copies2
bizhub 750/600 2-5
Before Making Copies
Chapter 2
Inside of Machine
2
Reminder 
Parts in the fusing unit are extremely hot. Touching any part in this unit 
may result in burns.
1
2
3
4
5 6 78
No.Part NameDescription
1 Toner cartridge When the toner is empty, replace the cartridge.
2 Toner-cartridge-securing lever Pull toward you to remove the toner unit when re-
placing the toner cartridge.
3 ADU unit Pull out when clearing paper misfeeds. For details 
on the levers and buttons of the ADU unit, refer to 
the screens that appear when a paper misfeed oc-
curs.
4 Lever M4 Lowered to the left in order to pull out the ADU unit 
when clearing paper misfeeds
5 Drum unit Forms the copy image
6 Fusing unit Fuses the image that was formed onto the paper
7 Main power switch Used to turn the machine on and off
8 Total counter Shows the total number of pages that have been 
printed
Downloaded From ManualsPrinter.com Manuals 
						

							2Before Making Copies
2-6 bizhub 750/600
Before Making Copies
Chapter 2
Options
1 2 3 4
5
67
8 9 11
1012
13 14
15
Downloaded From ManualsPrinter.com Manuals 
						

							Before Making Copies2
bizhub 750/600 2-7
Before Making Copies
Chapter 2
No.Part NameDescription
1 Main body The original is scanned by the scanner section, and 
the scanned image is printed by the printer section. 
Referred to as the “machine”, the “main unit”, or the 
“750/600” throughout the manual.
2 Shift tray SF-601 Separates copies fed out at an offset
3 Post inserter PI-501 Allows cover sheets to be inserted into copies if in-
stalled onto finisher FS-504/FS-505/FS-602, and al-
lows the functions of installed finishers to be used 
manually
4 Punch  kit  PK-505 Allows hole punching to be used if installed onto fin-
isher FS-504/FS-505/FS-602 
Referred to as the “punch kit” throughout the man-
ual.
5 Finisher FS-504/FS-505 Feeds out printed pages. The “Sort”, “Group”, “Off-
set” + “Sort”, “Offset” + “Group”, “Face Up” and 
Staple settings are available.
6 Finisher FS-602 Feeds out printed pages. The “Sort”, “Group”, “Off-
set” + “Sort”, “Offset” + “Group”, “Face Up”, Sta-
ple, “Fold & Staple”, “Half Fold” and “Tri-Fold” 
settings are available.
7 Z folding unit ZU-602 Allows holes to be punched for filing and allows 
pages to be folded in a zigzag if installed onto fin-
isher FS-504/FS-505/FS-602
8 Large capacity unit LU-402 Can be loaded with up to 4,000 sheets of paper 
(20lb)
Referred to as the “LCU” throughout the manual.
9 Large capacity unit LU-401 Can be loaded with up to 4,000 sheets of paper 
(20lb)
Referred to as the “LCU” throughout the manual.
10 Key counter Controls the number of copies produced
11 Hard disk HD-503 Increases the number of original pages that can be 
stored and enables the “Set Numbering” and Box 
functions to be used 
Referred to as the “hard disk” or “HDD” throughout 
the manual.
12 Image controller IC-202 Allows this machine to be used as a network printer 
(optional)
13 Local interface kit EK-701 Used for making a local connection between this 
machine and the computer
14 Fax kit FK-502 Allows this machine to be used as a fax machine
15 Security Kit SC-501 Installed to encode the data saved on the hard disk 
so that the hard disk can be used more safely.
Downloaded From ManualsPrinter.com Manuals 
						

							2Before Making Copies
2-8 bizhub 750/600
Before Making Copies
Chapter 2
Large Capacity Unit LU-401/LU-402
11 22
3
3
4
4
6 6
7
75
5
LCU LU-401
LCU LU-402
No.Part NameDescription
1 Upper door of the paper feed cab-
inetOpened when loading paper or clearing a paper 
misfeed
2 Left-side door of the paper feed 
cabinetOpened when clearing paper misfeeds
3 LCU lever Lowered when clearing paper misfeeds
4 Paper guides Positions the sides of the paper to be loaded.
5 Bottom-plate-lowering  button Pressed to lower the bottom plate in the tray to load 
paper
6 Bottom plate Raised as the paper is used. Lower by pressing the 
bottom-plate-lowering button.
7 Trailing-edge guide Positions the trailing edge of the paper to be load-
ed.
Downloaded From ManualsPrinter.com Manuals 
						

							Before Making Copies2
bizhub 750/600 2-9
Before Making Copies
Chapter 2
Finisher FS-504/FS-505/FS-602 (+ Punch Kit PK-505)
1 4
31 4
3
2
Finisher FS-602
No.Part NameDescription
1 Finisher door Opened when clearing paper misfeeds or staple 
jams or when replacing the staple cartridge, or 
when emptying the punch dust box if punch kit PK-
505 is installed
2 BM tray Collects pages printed with the “Half Fold”, “Fold & 
Staple”, or “Tri-Fold” settings or with the “Cover 
Mode” function
3 Main tray Collects printed pages
4 Sub tray Collects printed pages
Finisher FS-504/FS-505
Downloaded From ManualsPrinter.com Manuals 
						

							2Before Making Copies
2-10 bizhub 750/600
Before Making Copies
Chapter 2
4
34
3
1
1
59 2
5
8
7
62
10
10 11
11
Finisher FS-602Finisher FS-504
+Punch Kit PK-505
Finisher FS-505
+Punch Kit PK-505
4
3
1
9 2
5
82
10 11
Downloaded From ManualsPrinter.com Manuals 
						

							Before Making Copies2
bizhub 750/600 2-11
Before Making Copies
Chapter 2
No.Part NameDescription
1 Inlet lever Lowered when clearing paper misfeeds
2 Punch kit (optional) Punches holes for filing printed pages when the 
punch kit is installed onto finisher
3 Cover sheet conveyance lever Moved to the left when clearing paper misfeeds
4 Sub tray conveyance lever Moved to the right when clearing paper misfeeds
5 Stacker conveyance lever Moved down and to the left when clearing paper 
misfeeds
6 Lower lever Moved to the left after pulling out the stacker unit 
when clearing paper misfeeds
7 Knob Turned when clearing paper misfeeds
8 Stacker  unit Mounts the stapler. Also includes the equipment for 
folding in half and in three and for center binding on 
FS-602.
9 Punch dust box (optional) Removed when emptying punch dust that has ac-
cumulated from using the Punch settings (See 
p. 9-15.)
10 Stacker unit handle Used to pull out the unit when clearing paper mis-
feeds in the stacker unit and when refilling the sta-
ples
11 Staple cartridge Removed when refilling the staples (See p. 9-7.)
Downloaded From ManualsPrinter.com Manuals