Konica Minolta bizhub 420 User Manual

Supplies & Handling11
bizhub 500/420/360 (Phase 3) 11-17
9Return the staple holder to the 
stapler, and push it down until it 
clicks in place.
10Close the finisher front door.
Stapler will return to its original 
position, then the Basic screen will 
be restored.
2
1
Downloaded From ManualsPrinter.com Manuals 

11Supplies & Handling
11-18 bizhub 500/420/360 (Phase 3)To replace the staple cartridge for Saddle stitcher SD-502
0Be sure to replace the saddle staple cartridge after displaying the 
message, otherwise the machine may be dameged.
1Pull the saddle stitcher tray open and 
hold it as it is.
– It is not possible to leave the tray 
is kept open.Do not release it 
suddenly.
– If the extensible tray of the tray 1 
just under the saddle stitcher tray 
is withdrawn, push it back to its 
original position,...

Supplies & Handling11
bizhub 500/420/360 (Phase 3) 11-19
4Install the new saddle staple 
cartridge into the staple cartridge.
– Firmly insert the new cartridge 
into staple holder.
5Push down the top cover to return it 
to its original position.
6Remove the lock tape from the 
cartridge.
7Return the staple holder to the 
stapler.
– Hold the staple holder as shown 
right.
Downloaded From ManualsPrinter.com Manuals 

11Supplies & Handling
11-20 bizhub 500/420/360 (Phase 3)– While keeping the saddle stitcher 
tray open, push in the staple 
holder to its original position, 
then pull it up until it clicks in 
place.
– Gently return the saddle stitcher 
tray to its original position.
8Open the stapling part of the saddle 
stitcher, then close it.
The saddle stitcher will be reset, and 
the copying job using Fold & Staple 
mode will be available.
Downloaded From ManualsPrinter.com Manuals 

Supplies & Handling11
bizhub 500/420/360 (Phase 3) 11-21
11.4 Emptying Dust Boxes
Even when the punch dust box of the Finisher FS-511 is full, the message is 
not displayed. Before using punch mode, perform the following procedure to 
check if the punch dust box, if needed. To empty the dust box, see the 
following pages.
When the punch dust box of the Punch unit PU-501 mounted on the Finisher 
FS-510, the following message will be displayed on the screen, and the 
finished set will be output without...

11Supplies & Handling
11-22 bizhub 500/420/360 (Phase 3)To empty the dust box of FS-511
0Even when the punch dust box is full, the message is not displayed. 
Before using punch mode, perform the following procedure to check if 
the punch dust box, if needed. 
0The punch dust box is not disposable. Be sure to return it to its original 
position.
1Slide the finisher to the left.
– Holding the finisher handle on the 
top, slide the finisher to the left 
until it stops.
2Open the finisher right door FN7....

Supplies & Handling11
bizhub 500/420/360 (Phase 3) 11-23
4Empty the punch dust box.
5Return the punch dust box, then 
close the finisher right door [FN7].
6Slide the finisher to the right to return 
it to its original position.
Downloaded From ManualsPrinter.com Manuals 

11Supplies & Handling
11-24 bizhub 500/420/360 (Phase 3)To empty the dust box of PU-501
1Open the finisher front door.
2Pull out the punch dust box.
3Empty the punch dust box.
4Return the punch dust box, then 
close the finisher front door.
– Firmly reinstall the punch dust 
box.
Downloaded From ManualsPrinter.com Manuals 

12Troubleshooting
Downloaded From ManualsPrinter.com Manuals 

Downloaded From ManualsPrinter.com Manuals