JBL Synthesis Sdp-5 Manual

Introduction
SDP-5
ix
NORSK
VIKTIG INFORMASJON OM SIKKERHET
•Ta vare på denne veiledningen for senere bruk.
•Følg alle anvisningene og advarslene som er angitt på apparatet.
•Apparatet skal alltid anvendes med korrekt spenning. Produktbeskrivelsen inneholder
spesifikasjoner for strømkrav. Vær oppmerksom på at det ved ulike driftsspenninger kan
være nødvendig å bruke en annen ledning- og/eller støpseltype.
•Apparatet skal ikke monteres i skap uten ventilasjon, eller direkte over varmeproduserende
utstyr,...

Introduction
JBL Synthesis
x
Unpacking and Inspection
After unpacking the unit, save all packing materials in case the unit
ever needs to be shipped. Thoroughly inspect the modules and
packing materials for signs of damage. Report any damage to the
carrier at once; report equipment malfunction to the dealer.
Auspacken und Überprüfung
Bewahren Sie nach dem Auspacken des Geräts das
Verpackungsmaterial für den Fall auf, dass Sie das Gerät wieder
versenden müssen. Überprüfen Sie die Module und die...

1
Getting Started
About the SDP-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Highlights • Product Registration
Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Remote Control Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 

Getting Started
JBL Synthesis
1-2With four floating-point SHARC™ digital signal processing (DSP)
engines, the SDP-5 boasts enormous processing power. These
powerful processors perform custom processing such as LOGIC7
decoding, bass enhancement, dialog enhancement, auto azimuth,
5-speaker enhancement, bass management, high-precision digital
crossovers, and audio controls. These features are available at
sample rates up to 96kHz, with 24-bit resolution to retain top
performance from all sources. In...

Getting Started
SDP-5
1-3 Complementing its audio performance, the SDP-5 features two
broadcast-quality video switchers. A wide-bandwidth component
video switcher accepts analog component or RGB video signals,
while a composite and S-video switcher accepts high-quality NTSC,
PAL, or SECAM video signals. The component video switcher can
pass High-Definition TV (HDTV) signals, as well as Standard-
Definition TV signals. Both switchers are designed to pass video
signals without alteration or...

Getting Started
JBL Synthesis
1-4
Do Not . . .•Place the SDP-5 on a thick rug or carpet or cover the SDP-5
with a cloth, as this might prevent proper cooling.
•Place the SDP-5 on a windowsill or in another location in which
it will be exposed to direct sunlight.
•Obstruct the front panel IR receiver window shown on page
2-3. The remote control must be in line of sight with the IR
receiver for proper operation. Refer to page 2-9 for more
information about remote control operation considerations....

Getting Started
SDP-5
1-5REMOTE CONTROL BATTERY INSTALLATIONThe remote control requires two AA batteries that should be replaced as needed. It is recommended to use Alkaline batteries, which last longer
without leaking. When the batteries are low on power, the remote control enters a low-voltage condition that prevents it from operating the
SDP-5. When this occurs, follow the instructions below to replace the batteries. Normal operation will resume when the new batteries are
installed.  
To replace the...

2
Basic Operation
Front Panel Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Rear Panel Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Remote Control Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Operation Considerations • MAIN MENU • Menu Navigation • Menu Item Selection •
Command Bank Activation • Command Matrix
Understanding the Zones . . . . . . . . . . . . . . . . . . . . . . ....

Basic Operation
JBL Synthesis
2-21. Standby Button
Activates and deactivates standby mode when the SDP-5 is
powered on with the rear panel power switch (2-5). The
standby button performs no function when the SDP-5 is
powered off with the rear panel power switch.
When standby mode is activated, pressing the standby button
deactivates standby mode and activates the SDP-5, including
all zones that were activated during the previous operating
session. When standby mode is deactivated, pressing the
FRONT...

a remote control command is received. A red LED lights when
the A/D converters are overloading. And, a blue LED lights
when the SDP-5 is powered on and activated – even if the
FRONT PANEL DISPLAY menu STATUS parameter is set to
ALWAYS OFF (3-52).
4. Volume Knob
Adjusts volume level in the Main Zone or Zone 2.
Note:When SDP-5 output levels have been properly
calibrated (3-39), the +0dB volume level settingcorresponds to THX reference levels (75dB).
To use the volume knob to adjust Main Zone volume level:...